RightAngle NewHeights Electric Height Adjustable Workstation Manuals

4 3 1 2 4 YOU MAY HAVE (2) JOINER PLATES PAGE 1 OF 4 HARDWARE PACK # 52226 PLUS CENTER LEG BRACKET HARDWARE SURFACES VERSION DATED: 10/8/12 4 SURFACES WITH (8) WOOD SCREWS HOLES ARE PROVIDED FOR THE JOINER PLATE(S). ATTACH THEM TO THE WORK- AND 3" FROM THE EDGE(S) OF THE WORKSURFACES. NO PILOT 1 LEVEL ALIGN THE HOLES IN THE U-CHANNEL(S) WITH THE PILOT HOLES IN THE WORK- TAPE MEASURE SURFACE(S) ALLEN WRENCH (PROVIDED) 1 7/32" HEX HEAD DRIVER BID OR #2 SQUARE HEAD DRIVER BIT (OPT) #2 PHILLIPS HEAD DRIVER BIT CORDLESS DRILL . ATTACH THE U-CHANNEL(S) TO THE WORKSURFACE(S) WITH TOOLS REQUIRED FOR ASSEMBLY: ON THE SEAM BETWEEN THE WORK- (10) WOOD SCREWS NewHeights™ 3-LEG ELECTRIC HEIGHT ADJUSTABLE WORKSTATION ASSEMBLY 4 INSTRUCTIONS: STEP 1: ON THE 42" U-CHANNEL OR (12) WOOD SCREWS ON LAY THE WORKSURFACE(S) 1 ON A PROTECTED SURFACE WITH THE THE 54" U-CHANNEL. DO NOT OVER-TIGHTEN THE SCREWS. USE A LOW TORQUE PILOT HOLES FACING UP. IF YOUR WORKSTATION HAS U-CHANNEL(S) 2 SETTING ON THE DRILL. AND JOINER PLATE(S) 3 STEP 3: , ATTACH THEM AS FOLLOWS. IF NOT, PROCEED TO STEP 4. STEP 2: CENTER THE JOINER PLATE(S) U-CHANNELS 2 3 ARE INCLUDED ON 72" AND LARGER WORKSTATIONS. IN EACH JOINER PLATE. INSTRUCTION # 52746 ITEM # PART # DESCRIPTION QTY 1 VARIES WORKSURFACE(S) VARIES 2 VARIES 42" OR 54" U-CHANNEL * VARIES 3 800382 35UP 3x5 JOINER PLATE VARIES 4 51708 M5 x 18mm SQ/PH/WSHR HEAD WOOD SCREW VARIES 5 VARIES NewHeights COLUMN ASSY LH 1 6 VARIES NewHeights COLUMN ASSY 12" 3-LEGGED CENTER 1 7 VARIES NewHeights COLUMN ASSY RH 1 8 VARIES NewHeights 3-LEG CROSS SUPPORT BRACKET 1 9 VARIES NewHeights CROSS SUPPORT 3-LEG 2 10 VARIES 3/8 INTERIOR TOOTH STAR WASHER VARIES 11 VARIES 3/8-16 x 3/8 BUTTON HEAD SOCKET SCREW VARIES 12 800411 NewHeights/HOVER END CAP 4 13 50285 NewHeights HAND SWITCH 2 15 51951 WIRE MANAGEMENT J ** VARIES 16 52498 7/32" ALLEN WRENCH 1 6703 ZINSER ST., SCHOFIELD, WI 54476 PHONE: 800.298.4351 FAX: 866.882.9475 www.raproducts.com K&A MANUFACTURING ** USED INSTEAD OF U-CHANNELS ON SMALLER WORKSTATIONS DO NOT OPERATE THE UNIT UNTIL IT IS FULLY ASSEMBLED * USED ONLY ON 72" 3-LEG WORKSTATIONS READ ALL THE INSTRUCTIONS BEFORE BEGINNING STEPS 1-3

6703 ZINSER ST., SCHOFIELD, WI 54476 PHONE: 800.298.4351 FAX: 866.882.9475 www.raproducts.com VERSION DATED: 10/30/14 K&A MANUFACTURING M2 PAGE 1 OF 2 THE HOOKS MUST LOCK ONTO THE TABS AT THE CORD CONNECTION. FOLLOW THE RESET PROCEDURES ON PAGE 2. M1 ARE VISIBLE. STEP 7: WIRING DIAGRAM LH COLUMN RE-CONNECT THE CORDS TO THE CONTROL BOX AND THE CORD TAILS COMING OUT OF THE COLUMNS. INSTRUCTIONS TO REPLACE CORDS ON NewHeights WORKSTATIONS: STEP 1: UNPLUG THE POWER CORD FOR THE CONTROL BOX. STEP 2: DISCONNECT THE LEFT AND RIGHT HAND COLUMN CORDS FROM THE CONTROL BOX. STEP 3:DISCONNECT THE CORDS FROM THE SHORT CORD TAILS COMING OUT OF THE RIGHT AND LEFT HAND COLUMNS. STEP 4: DISCONNECT THE CORD FRON THE CENTER LEG IF YOU HAVE A 3-LEG WORKSTATION. STEP 5: REMOVE THE OLD CORDS FROM THE WIRE MANAGEMENT J-CHANNELS OR U-CHANNEL. STEP 6: RUN THE NEW CORDS THROUGH THE WIRE MANAGEMENT COMPONENTS. PLACE THE EXCESS CORD IN THE WIRE MANAGEMENT, NOTE: CROSS SUPPORT NOT SHOWN ON THIS VIEW SO OTHER COMPONENTS M3 BOTTOM VIEW OF WIRE RUNS THIS END GOES COLUMN RH LEFT COLUMN WIRE RIGHT COLUMN WIRE HAND SWITCH WIRE HAND SWITCH DISCONNECT DISCONNECT TO CONTROL BOX HS INSTRUCTION # 53088 TO COLUMNS THIS END GOES THIS SMALL TAB MUST GO UNDER THE LOCK ON THE MOTOR CORD SWITCH HAND CENTER COLUMN (3-LEG)