RightAngle NewHeights RECTANGULAR 3-LEG WORKSTATION Manuals

6703 ZINSER ST., SCHOFIELD, WI 54476 PHONE: 800.298.4351 FAX: 866.882.9475 www.raproducts.com K&A MANUFACTURING ON THE WORKSURFACE AS SHOWN. ALIGN THE HOLES IN THE 7/32" HEX HEAD DRIVER BIT OR 16 #2 SQUARE HEAD DRIVER BIT WITH THE HELP OF AN ASSISTANT, PLACE (4) STAR WASHERS ON A PROTECTED SURFACE WITH THE WORKSURFACE SUPPORTS WITH THE PILOT HOLES IN THE WORKSURFACE. SUPPORT SHOULD BE ATTACHED RESTING ON THE FEET OF THE COLUMN THE MOTOR WIRES MUST FACE THE INSIDE OF THE WORKSTATION. STEP 2: LEVEL 4 SPECIAL EXCEPTION: ON WORKSTATIONS INTO EACH END OF THE CROSS SUPPORT AT 4" ABOVE THE BOTTOM OF THE TOOLS REQUIRED FOR ASSEMBLY: WORKSURFACE SUPPORTS AND FULLY TIGHTEN ALL THE SOCKET SCREWS CORDLESS DRILL #2 PHILLIPS HEAD DRIVER BIT OR VERSION DATED: 5/10/13 PAGE 1 OF 3 PILOT HOLES FACING UP. PLACE THE LEFT HAND COLUMN ASSEMBLY 10 9 . INSERT AN END CAP ON (4) SOCKET SCREWS INSTRUCTION # 52778 INSERT (2) SHORTY PLUGS 10 THE RIGHT HAND COLUMN ASSEMBLY . INSERT THESE THROUGH THE HOLES AT THE ENDS AND 15 11 3 OF THE CROSS SUPPORT TAPE MEASURE 16 2 . PLACE (2) LOCK WASHERS INTO THE ACCESS HOLES AT THE CENTER OF , 14 HARDWARE PACK # THE CROSS SUPPPORT. ON (2) LOW HEAD SOCKET SCREWS STEP 4: 15 ASSEMBLIES TO ALLOW FOR CLEARANCE OF THE EQUIPMENT. , AND THE CENTER COLUMN . INSERT THESE THROUGH THE HOLES AT THE CENTER OF THE CROSS SUPPORT. THREAD ALL (6) SOCKETSCREWS INTO ON WHICH THE LifeBalance™ STATION IS BEING INSTALLED, THE CROSS 5 THE HOLES IN THE T-SLOT PLATES THAT ARE PRE-INSTALLED IN THE SLOTS IN THE COLUMNS. SEE DETAIL A. DO NOT FULLY TIGHTEN. . SEE THE DETAIL AT LEFT. STEP 3: ASSEMBLY ALLEN WRENCH PROVIDED 16 3/16" HEX HEAD DRIVER BIT LEVEL THE CROSS SUPPORT NewHeights™ RECTANGULAR 3-LEG WORKSTATION ASSEMBLY INSTRUCTIONS: STEP 1: LAY THE WORKSURFACE 1 ITEM # PART # DESCRIPTION QTY. 1 VARIES WORKSURFACE 1 2 VARIES NewHeights LEFT HAND COLUMN ASSY 1 3 VARIES NewHeights RIGHT HAND COLUMN ASSY 1 4 VARIES NewHeights CENTER COLUMN ASSY 1 5 800411 NewHeights/HOVER END CAP 2 6 50285 NewHeights HAND SWITCH 1 7 51951 WIRE MANAGEMENT J 3 8 51708 M5 x 18mm SQ/PH/WSHR HEAD WOOD SCREW 29 9 52477 3/8 INTERIOR TOOTH STAR WASHER 4 10 52470 3/8-16 x 3/8 BUTTON HEAD SOCKET SCREW 4 11 52059 5/8" SHORTY PLUG 2 12 50298 NewHeights CONTROL BOX 1 13 52498 7/32" ALLEN WRENCH 1 14 52425 3/8 x 1/2 x 1/8 HIGH COLLAR LOCK WASHER 2 15 52424 3/8-16 X 1/2 LOW HEAD SOCKET SCREW 2 16 800532 NewHeights 96" CROSS SUPPORT RECTANGULAR 3-LEG (91" ACTUAL) 1 15 14 9 1 2 4 3 16 WORKSURFACE SUPPORT STEPS 1-4 11 5 10 DETAIL A T-SLOT PLATE PRE-INSTALLED LOCATING THE CROSS SUPPORT (SEE EXCEPTION IN STEP 3) 16 4.00