Rosslare SA-23-B4 Manuals

AY-L23 and SA-23-B2/B4 Outdoor Long-Range RF Reader and Remote Controls Installation and Operation Manual 1 1. Introduction The AY-L23 is an outdoor long-range RF reader that acts as a receiver. It is compatible with Rosslare’s SA-23 wireless remote control transmitters:  SA-23-B2 – 2-Button Remote Control  SA-23-B4 – 4-Button Remote Control The AY-L23 reader and the remote controls are available in both G (433.92 MHz) and H (868.35 MHz) frequencies. The AY-L23 is not compatible with old remote controls such as: SA-26, SA-27, and SA-28. When the AY-L23 receives the a command signal from a SA-23-B2/B4 wireless transmitter, the AY-L23 outputs the ID to A_DATA0,A_DATA1 or B_DATA0,B_DATA1 to the attached controller and controls the function of the relay (open drain FET) A or B according to the SA-23-B2 remote’s command. The command signal consists of 3 parts:  ID (in Wiegand format)  ID output to A or B Wiegand Output according to the command in SA-23-B2  Relay Function A or B according to command in the SA-23-B2 Figure 1: AY-L23 and SA-23-B2/B4 AY-L23 SA-23-B2 SA-23-B4 2. Technical Specifications 2.1 AY-L23 Input Voltage 7 to 24 VDC Standby Current 26 mA (12 VDC) Maximum Operating Current 65 mA (12 VDC) Relay (FET, Open Drain) Current 200 mA (max voltage 40 V) Tamper Output Open collector, active Open, max. sink current is 16 mA Maximum Cable Distance to Controller 152 m (500 ft.) Wiegand Output Format Wiegand 26-Bit, 32-Bit, 34-Bit, 40-Bit (decided by remote) Frequencies G: 433.92 MHz H: 868.35 MHz Operating Temperature Range -31°C to 63°C (-25°F to 145°F) Operating Humidity Range 0 to 95% (non-condensing) Suitable for outdoor use (IP65) Dimensions (L x W x D) 145 x 43 x 20 mm (5.7 x 1.7 x 0.8 in.) 2.2 SA-23-B2/B4 Input Voltage 3 V Battery (CR 2450) Standby Current < 1 uA Max Operation Current 10 mA ID Format Programmed to Wiegand 26-Bit Frequencies G: 433.92 MHz (ASK) H: 868.35 MHz (ASK) Operating Temp. Range -31°C to 63°C (-25°F to 145°F) Operating Humidity 0 to 95% (non-condensing) Dimensions (L x W x D) 58 x 41 x 13.4 mm (2.3 x 1.6 x 0.5 in.) Weight AY-L23: 100.8 g (3.56 oz) SA-23: 21 g (0.74 oz) (without battery) 3. Mounting Instructions Determine an appropriate mounting position for the receiver. Do not mount the receiver near any source of wireless interference or on any metal surface. To mount the receiver: 1. Peel off the back of the self-stick mounting label template included with the unit and place at the desired mounting position. 2. Using the template as a guide, drill two holes (hole size is indicated on mounting template) for mounting the receiver to the surface. 3. Drill a 7/16” (10-mm) hole for the cable. 4. Remove the front case from the receiver. 5. Attach the receiver to the controller. (See wiring instructions) 6. Screw the receiver’s rear case onto its mounting location and return the front case onto the mounted rear case. The receiver is to be used with control panels whose power supply is UL Listed Class 2 or equivalent.