RS 219-765 Manuals

Note: Please read all relevant sections of this instruction leaflet before installing and/or operating the cleaner. The RS range of ultrasonic cleaning tanks provides the user with a complete range of functions and capacities for both light and heavy duty applications throughout industry. Features Super sealing 'O' rings. Recessed ventilation. Sealed membrane keypad (digital models). Over temperature thermostat (heated models). Operating level line. Quick disconnect drain (on 5.71 litres and above). Pour spout (on models below 5.71 litres). Non-skid feet. Integral handles. All models are supplied complete with lids. Solid and perforated insert trays are available for all models as extras. WARNING Do not place parts or containers directly on the bottom of the cleaning tanks; use a tray or wire to suspend items. Do not allow the solution to drop below the operating level line (one inch from the top) with the cleaner on. Do not ever use alcohol, gasoline or flammable solutions. Doing so could cause a fire or explosion. Use only water- based solutions. Do not ever use mineral acids or bleaches. These could damage the tank. To avoid electrical shock: Do unplug from power source before filling or emptying the tank. Do keep the control panel and the area around the cleaner clean and dry - wipe up solution which spills over the tank brim. Water and high voltage can cause electrical shock. Do not operate the cleaner without proper grounding. Do not remove the grounding prong on the line cord plug. Do not disassemble your cleaner - high voltage inside the cleaner is dangerous. Do not immerse the cleaner in water. To prevent personal and/or property damage: Do operate the cleaner with a vented cover or no cover. Do use water-based solutions. Do not ever use alcohol, gasoline or flammable solutions. Doing so could cause a fire or explosion and will void your warranty. Use only water-based solutions. Do not ever use mineral acids or bleaches. These could damage the tank. Do not touch the stainless steel tank or cleaning solution - they may be hot. Do not allow fluid temperature to exceed 70¡C (160¡F). Do not place your fingers or hands into the tank while the cleaner is operating. Doing so may cause discomfort and possible skin irritation. Avoid contact with solutions and provide adequate ventilation. To prevent damage to the cleaner: Do change your solution regularly. Do not cover vents on the cover. Do not operate the cleaner dry. Do not place parts or containers directly on the bottom of the cleaning tank; use a tray or wire to suspend items. Failure to comply may cause transducer damage and will void your warranty. Do not allow the solution to drop below the operating level line (one inch from the top) with heat or ultrasonics on. Failure to comply may cause transducer and/or heater damage and will void your warranty. If warm water is added to the tank, do not allow temperature to exceed 70¡C. Failure to comply with these warnings will void your warranty. Before using your ultrasonic cleaner, please read and thoroughly understand these warnings. Failure to follow them may result in serious personal injury or property damage. Installing your cleaner Check the plate on the back of the cleaner for correct power requirements. Position your cleaner within easy reach of a standard grounded electrical outlet. Do not place the cleaner on a circuit which could become overloaded. If your cleaner does not operate correctly, first refer to the troubleshooting section for possible causes. Operating your mechanical timer cleaner. RS stock no. 219-765 Before you start cleaning Note: If this is the first time you are running the cleaner, or if you have changed cleaning solution, you must degas the solution. If not, skip to 'Cleaning items". Degassing Cleaning items Note: To stop ultrasonics at any time, turn the TIMER to zero. Ultrasonic Cleaning Tanks Stock No. 219-765, 219-771, 219-787, 219-793, 219-800 and 219-816 Step 1 Action Select your cleaning solution. 3 Add cleaning solution to the tank water. 4 Plug the cleaner into a grounded outlet. 2 Allowing for the volume of the parts you will be cleaning and cleaning solution, fill the tank with warm tap water to the operating level line (one inch from the top). Step 1 Action Turn the TIMER to 5-10 and let the cleaner run to allow the solution to "degas". ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥