RUPTELA HCV5 Series Manuals

Main Support no.: +370 5 2045030 Polish Support no.: +48 22 2092532 Ukrainian Support no.: +380 947 107319 Web: www.ruptela.lt Email: [email protected] Contacts: Connection Instructions Tracking devices and LLS (RS485 Digital Fuel level Sensor) LLS Configuration It is very important to configure your LLS correctly before connecting it to the tracking device. Key points for the configuration: ❖ The LLS Baud rate value has to be set to 19200 ❖ The LLS must be configured to send data only upon request from the tracking device ❖ LLS data output should be binary, 10 or 12 bits Connecting the LLS to the Tracking Devices LLS (20160, RS485) should be connected to the tracking device as follows (see the pictures below): Advanced Family devices:

Main Support no.: +370 5 2045030 Polish Support no.: +48 22 2092532 Ukrainian Support no.: +380 947 107319 Web: www.ruptela.lt Email: [email protected] Contacts: Connection Instructions Tracking Devices and LLS (RS232 Digital Fuel Level Sensor) LLS Configuration It is very important to configure your LLS correctly before connecting it to the tracking device. Key points for the configuration: ❖ The LLS Baud rate value has to be set to 19200. ❖ The LLS must be configured to send data only upon request from the tracking device. ❖ LLS data output should be binary, 10 or 12 bits. Connecting the LLS to the Tracking Devices LLS (20160, RS232) should be connected to the tracking device as follows (see the pictures below): Advanced Family devices:

www.ruptela.com [email protected] | +370 5 2045030 1 Tachograph Solution Quick Start Guide Q HCV5 This quick start guide is only for the direct connection. For connection via the front interface, please refer to the user manual. Make sure that you have: • A vehicle with one of the following tachographs: o Siemens VDO 1381 (versions higher than 1.3A) o Stoneridge SE5000 (versions higher than 7.0) o EFAS-4 or newer • A computer with Windows 7/8/10 • An internet connection (or a predownloaded Device Center) • A USB A to USB micro (Type B) cable • A tachograph harness (recommended) Device overview Indication LEDs Opening handles Grooves for zip-ties GNSS antenna port 16 Pin port Micro USB port Audio port 14 Pin port Indication LED patterns LED Pattern Description GNSS Once every second Accurate signal Once every 0.4 seconds No signal Cellular Once every 4 seconds Connected to network and internet Once every second Connected to network, no internet Once every 0.2 seconds No signal Always on Link with the server is open Peripherals Always off No devices connected Once every 5 seconds One device connected Twice every 5 seconds Two devices connected Three times every 5 seconds Three devices connected All Once every 5 seconds Sleep mode

www.ruptela.com [email protected] | +370 5 2045030 1 HCV5/LCV5 Quick Start Guide Q Make sure that you have: • A computer with Windows 7/8/10 • An internet connection (or a predownloaded Device Center) • A USB A to USB micro (Type B) cable • Tools for installation and wire connection: a panel removing tool, a wrench, a crimp terminal, zip-ties (or double-sided tape) Device overview Indication LEDs Opening handles Grooves for zip-ties GNSS antenna port 16 Pin port Micro USB port Audio port 14 Pin port 14 Pin cable pinout No. Pin Wire color Description 1 +BAT Red Power supply (9- 32 V) 2 DOUT1 Purple Digital output 1 3 1W Data Green/Yellow 1-Wire data 4 DIN3 Pink Digital input 3 5 DIN4 Yellow Digital input 4 6 CAN2-L Blue CAN Low 7 K-Line Brown K-Line 8 GND Black Ground 9 DOUT2 Orange Digital output 2 10 1W+5V Red/Yellow 1-Wire power 11 AIN2 Green Analogue input 2 12 AIN1 Grey Analogue input 1 13 CAN2-H White CAN High 14 SW CAN Green/White Single-Wire CAN 16 Pin cable pinout No. Pin Wire color Description 1 PortC-485 A White/Brown RS485 line A 2 PortA-RS232 TX Green/Brown PortA RS232 TX 3 PortB-RS232 TX Pink/Green PortB RS232 TX 4 DIN1 Yellow/Black Digital input 1 5 DIN2 Pink/Black Digital input 2 6 AIN4 White/Green Analogue input 4 7 CAN1-L Blue/Red CAN Low 8 GND Black Ground 9 PortC-485 B Yellow/Brown RS485 line B 10 PortA-RS232 RX Blue/Yellow PortA RS232 RX 11 PortB-RS232 RX Red/Cyan PortB RS232 RX 12 DOUT3 White/Purple Digital output 3 13 DOUT4 White/Orange Digital output 4 14 AIN3 White/Grey Analogue input 3 15 CAN1-H White/Red CAN High 16 1W+5V Red/ Yellow 1-Wire power

www.ruptela.com [email protected] | +370 5 2045030 1 OBD Solution Quick Start Guide Q HCV5 LCV5 Make sure that you have: • An OBD2 standard compatible vehicle • A computer with Windows 7/8/10 • An internet connection (or a predownloaded Device Center) • A USB A to USB micro (Type B) cable • An OBD2 harness (recommended) Device overview Indication LEDs Opening handles Grooves for zip-ties GNSS antenna port 16 Pin port Micro USB port Audio port 14 Pin port Indication LED patterns LED Pattern Description GNSS Once every second Accurate signal Once every 0.4 seconds No signal Cellular Once every 4 seconds Connected to network and internet Once every second Connected to network, no internet Once every 0.2 seconds No signal Always on Link with the server is open Peripherals Always off No devices connected Once every 5 seconds One device connected Twice every 5 seconds Two devices connected Three times every 5 seconds Three devices connected All Once every 5 seconds Sleep mode

HCV5 User Manual v1.0 2020-07-16