Saab R5 SUPREME AIS Manuals

OPERATION & INSTALLATION MANUAL Saab TransponderTech R5 SOLID AIS System

R5 SUPREME NAV System Operator Short Instruction 7000 118-369 A1 This quick user guide serves as a complement to the standard manual with P/N: 7000 118-301 found on the documentation CD. This guide is designed to give immediate access to essential information when operating the system on a daily basis. Please visit our web-site for the latest news regarding this and other ship borne products. Our web-site also contains contact information to our dealers and service stations world-wide and much more. www.saabgroup.com/transpondertech Saab TransponderTech AB R 5 S U P R E M E N A V SYSTEM MODES Important: The R5 SUPREME Navigation System is offered in GPS and DGPS configuration. In addition, the R5 CDU can be installed using different system modes. Mainly:  Navigation System – Standalone or in network  Combined AIS & Navigation System This short instruction covers Navigation System functions only. GENERAL OPERATION SYSTEM NAVIGATION The R5 CDU is equipped with a resistive touch screen to be used for system navigation. The system can also be navigated using the keypad. Use the Arrow keys to navigate the system views. Press ENTER  to open a view. Press ESC to go back. CHANGING PARAMETERS Many views contain parameters that can be edited. To edit a parameter, press the parameter value or select it by using the ARROW KEYPAD and press ENTER . Press BACKSPACE  button to delete characters. Press ENTER  to accept input after editing a parameter. Press ESC to undo changes. Press the Save button to save and exit a view. Data can be entered to the system in the following ways: 1. Numbers: A virtual numerical keypad will be shown for numerical parameters. 2. Text: A virtual keyboard will be shown for textual parameters. 3. Selection List: Parameters with fixed values are displayed in a drop-down list, shown when the parameter value is pressed. Select one of the listed values. 4. Selection List and numeric input: In some views it is possible to select items in a list of predefined values. It may also possible to enter a custom number. To do this, select the Numerical Input choice and input a numerical value using the virtual numerical keypad shown. DO NOT TURN OFF THE SYSTEM WITHIN 2 SECONDS OF A PARAMETER CHANGE!

R5 SOLID Installation Short Instruction 7000 118-201 A3 RECOMMENDED PHYSICAL LOCATION Please consult the complete system manual P/N: 7000 118-200 for physical location aspects of the Transponder units and the VHF and GPS antennas. SYSTEM MODE Important: The R5 SOLID can operate in two different system modes, Class A mode (default) and Inland mode. Inland mode is currently only applicable to European river going vessels. Set correct mode in: Main Menu Config System Settings System Mode Instruction only applicable to Inland AIS installations will be in brown print. R 5 S O L I D A I S This quick installation guide serves as a complement to the standard manuals found on the documentation CD. It is designed to give immediate access to essential information when executing an installation and a functionality test. Installation of the R5 Solid AIS System should always be carefully planned and executed by skilled personnel. Please visit our website for the latest news regarding this and our other shipborne products. Our website contains contact information to our dealers and service stations worldwide and much more. www.saabgroup.com/transpondertech For the complete manual set please see the included documentation CD. Physical R5 Solid Size W x H x D: 238x87x173 (mm) Gimbal Mount Size W x H x D: 252x95x65 (mm) Power Input 24 VDC (Max 30 VDC) Power Consumption: 17W (0.7A @ 24VDC) Required power on current: 4A GPS Receiver (AIS internal) Receiver: 50 CH Frequency: L1 (1575.42 MHz) Update Rate: 2 Hz Position accuracy (SA off) Position <2.0 m DGPS (CEP, 50%) Position <2.5 m GPS (CEP, 50%) Antenna feeding: 5 VDC Electrical Interfaces RS 422 Port Default speed (bps) Pilot In/Out 38400 ECDIS In/Out 38400 LR In/Out 9600 Sensor 1 In 4800 Sensor 2 In 4800 Sensor 3 In 4800 RS 232 Port Default speed (bps) RS232 In/Out 38400 Signal connector: 26 pin HD-SUB (M) RS-232 connector: 9 pin D-SUB (M) Power connector: 4 pin ConXall (M) GPS 50 ohm antenna connector TNC female VHF 50 ohm antenna connector BNC female Chassis GND screw size: M6 Cables (recommended) VHF and GPS RG214/U Sensors e.g. Gyro RFE-HFI 2x2x0.75 mm2 VHF Transceiver Frequency 156-163 MHz Output power 1/12.5 W Channel bandwidth 25 kHz Bit Rate 9600 bps Intervals between position reports 1-180 s Modulation FM-GMSK/GFSK Transmitter 1 Receivers 3 Transceiver Sensitivity <-107 dBm Environmental data Protected environment (IEC 60945) Operating temperature -15 °C to 55 °C Compass safe distance 60 cm to standard magnetic compass 45 cm to steering magnetic compass The R5 Solid AIS System is compliant with the following Standards IMO Performance Standard for AIS (MSC 74(69) Annex 3) ITU-R M. 1371-4 ITU-R M. 825-3 ITU-R M. 1084-3 IEC 61993-2 Edition 1 IEC 61162-1/2 Edition 4 (NMEA 0183, Version 4.0) IEC 61108-1 Edition 2 IEC 60945 Edition 4 IEC 62288 Edition 1 IALA Guidelines on AIS Specifications subject to change without notice

R5 SUPREME AIS Installation Short Instruction 7000 118-363 C1 R 5 S U P R E M E A I S RECOMMENDED PHYSICAL LOCATION Please consult the complete system manual P/N: 7000 118-300 for physical location and mounting aspects of the system units and the VHF and GPS antennas. SYSTEM MODE Important: The R5 SUPREME CDU can be set up to operate in different system modes, AIS, Navigation or a Combined AIS and Navigation mode. This short instruction deals with AIS functions only. If Navigation system functions are activated, additional setup will be necessary. This quick installation guide serves as a complement to the standard manuals found on the documentation CD. It is designed to give immediate access to essential information when executing an installation and a functionality test. Installation of the R5 SUPREME AIS Transponder System should always be carefully planned and executed by skilled personnel. Please visit our web-site, saab.com, for the latest news regarding this and other Saab products. AIS equipment is currently found under : saab.com/security/maritime-traffic- management/traffic-management/ Our product pages also contains contact information to our dealers and service stations world-wide and much more Physical R5 SUPREME AIS Transponder Size W x H x D: 227x77x192 [mm] R5 SUPREME CDU Size W x H x D: 255x140x84 [mm] Gimbal Mount Size W x H x D: 295x170x84 [mm] Power R5 SUPREME AIS Transponder Input 12/24 VDC (Max 30 VDC) Power Consumption: 20W (60W peak) R5 SUPREME CDU Input 12/24 VDC (Max 30 VDC) Power Consumption: 13W GPS Receiver (AIS internal) Receiver: 50 CH Frequency: L1 (1575.42 MHz) Update Rate: 2 Hz Position accuracy (SA off) Position <2.5 m GPS (CEP, 50%) Antenna feeding: 5 VDC Electrical Interfaces R5 SUPREME AIS Transponder RS 422 Port Default speed (bps) Pilot In/Out 38400 ECDIS In/Out 38400 LR In/Out 9600 Sensor 1 In/Out 4800 Sensor 2 In/Out 4800 Sensor 3 In/Out 4800 Note: RTCM-104 corrections are accepted on any of the ports above, Signal connector RS422: 26 pin HD-SUB (M) Signal connector I/O: 26 pin HD-SUB (F) Ethernet connector: RJ45 Power connector: 4 pin ConXall (M) GPS 50 ohm antenna connector TNC female VHF 50 ohm antenna connector BNC female R5 SUPREME CDU RS 422 Port Default speed (bps) CDU Pilot In/Out 38400 Ethernet connector: RJ45 Power connector: 4 pin ConXall (M) Cables (recommended) VHF and GPS RG214/U Sensors e.g. Gyro RFE-HFI 2x2x0.75 mm2 Ethernet Cable CAT-5 VHF Transceiver Frequency 156-163 MHz Output power 1/12.5 W Channel bandwidth 25 kHz Bit Rate 9600 bps Intervals between position reports 1-180 s Modulation FM-GMSK/GFSK Transmitter 1 Receivers 3 Transceiver Sensitivity <-107 dBm Environmental data Protected environment (IEC 60945) Operating temperature -15 °C to 55 °C Compass safe distance R5 SUPREME AIS Transponder 65 cm to standard magnetic compass 40 cm to steering magnetic compass R5 SUPREME CDU 75 cm to standard magnetic compass 50 cm to steering magnetic compass The R5 SUPREME AIS Transponder System is compliant with the following Standards IMO Performance Standard for AIS (MSC 74(69) Annex 3) ITU-R M. 1371-5 ITU-R M. 825-3 ITU-R M. 1084-5 IEC 61993-2 Edition 2 IEC 61162-1/2 Edition 4/1 (NMEA 0183, Version 4.0) IEC 61108-1 Edition 2 IEC 60945 Edition 4 IEC 62288 Edition 2 IALA Guidelines on AIS Specifications subject to change without notice

R5 SUPREME AIS Operator Short Instruction 7000 118-364 A1 This quick user guide serves as a complement to the standard manual with P/N: 7000 118-300 found on the documentation CD. This guide is designed to give immediate access to essential information when operating the system on a daily basis. Please visit our web-site for the latest news regarding this and other ship borne products. Our web-site also contains contact information to our dealers and service stations world-wide and much more. www.saabgroup.com/transpondertech Saab TransponderTech AB R 5 S U P R E M E A I S SYSTEM MODES Important: The R5 SUPREME AIS Transponder System can be set up to operate in different system modes, AIS, Navigation or a Combined AIS and Navigation mode. This short instruction deals with AIS functions only. If Navigation system functions are activated, additional symbols and menus will be available. GENERAL OPERATION SYSTEM NAVIGATION The R5 SUPREME CDU is equipped with a resistive touch screen as well as a keypad to be used for operation of the system. When using the Arrow keys to navigate the system views, selected items will be highlighted by an orange frame. Press ENTER to open a view. Press to go back. CHANGING PARAMETERS Many views contain parameters that can be edited. To edit a parameter, press the parameter value or select it by using the ARROW KEYPAD and press ENTER . Changes will not take effect immediately. Press Save on screen button after editing parameters to save and exit the view. Press Back on screen button to cancel changes. Data can be entered to the system in the following ways: 1. Text / Numbers: A virtual keyboard/keypad will popup when editing text or number fields. Press characters on screen directly, or use Arrow keys to highlight and press ENTER key to input a character. Press VIRTUAL KEYPAD ENTER key to accept new input after editing. Press ESC to undo changes. 2. Selection List: Parameters with fixed values are displayed in a drop-down list, shown when the parameter value is pressed. Select one of the listed values. 3. Selection List and numeric input: In views like the Send AIS Message it is possible to select a target MMSI in a list of predefined values based on received targets MMSI. It is also possible to enter any MMSI number. To do this, select the Numerical Input choice and input a numerical value using the virtual numerical keypad shown. DO NOT TURN OFF TRANSPONDER POWER WITHIN 2 SECONDS OF A PARAMETER CHANGE!

OPERATION & INSTALLATION MANUAL Saab TransponderTech R5 SUPREME AIS Transponder System

SYSTEM MODES Important: The R5 SUPREME CDU can be set up to operate in different system modes, AIS, Navigation or a Combined AIS and Navigation mode. This short instruction deals with AIS functions only. If Navigation system functions are activated, additional symbols and menus will be available. GENERAL OPERATION SYSTEM NAVIGATION The R5 SUPREME CDU is equipped with a resistive touch screen as well as a keypad to be used for operation of the system. When using the Arrow keys to navigate the system views, selected items will be highlighted by an orange frame. Press ENTER to open a view. Press to go back. CHANGING PARAMETERS Many views contain parameters that can be edited. To edit a parameter, press the parameter value or select it by using the ARROW KEYPAD and press ENTER . Changes will not take effect immediately. Press Save on screen button after editing parameters to save and exit the view. Press Back on screen button to cancel changes. Data can be entered to the system in the following ways: 1. Text / Numbers: A virtual keyboard/keypad will popup when editing text or number fields. Press characters on screen directly, or use Arrow keys to highlight and press ENTER key to input a character. Press VIRTUAL KEYPAD ENTER key to accept new input after editing. Press ESC to undo changes. 2. Selection List: Parameters with fixed values are displayed in a drop-down list, shown when the parameter value is pressed. Select one of the listed values. 3. Selection List and numeric input: In views like the Send AIS Message it is possible to select a target MMSI in a list of predefined values based on received targets MMSI. It is also possible to enter any MMSI number. To do this, select the Numerical Input choice and input a numerical value using the virtual numerical keypad shown. DO NOT TURN OFF TRANSPONDER POWER WITHIN 2 SECONDS OF A PARAMETER CHANGE! This quick user guide serves as a complement to the standard manual with P/N: 7000 118-300 found on the documentation CD. This guide is designed to give immediate access to essential information when operating the system on a daily basis. Please visit our web-site, saab.com, for the latest news regarding this and other Saab products. AIS equipment is currently found under : saab.com/security/maritime-traffic- management/traffic-management/ Our product pages also contains contact information to our dealers and service stations world-wide and much more