-
C O N T E N T S
2
-
2. Adjustments by menus
3
-
- Type : 23.5mm×15.7mmCCD
4
-
- CCD shift type
5
-
PC with processor better than Pentium III 450Mz
6
-
3. Names of Working Parts
7
-
Cable switch port
8
-
Battery cover &
9
-
4. Using the Button Functions
10
-
① Exposure bracket button
11
-
① Metering mode lever
12
-
■ Functions of buttons used during playback.
13
-
① MENU button
14
-
5. LCD Monitor Indications
15
-
1. Capture quality (Image file type)
18
-
6. Viewfinder Indications
19
-
11. EV compensation
20
-
7. LCD Panel Indications
21
-
1. GX-10 : FIG. 1
22
-
2. GX-10 : FIG. 2
23
-
3. GX-10 : FIG. 3
24
-
4. GX-10 : FIG. 4
25
-
4C3, 4D6, 4E7, 4F3, 4F5, 4G3, 4H4
34
-
DIGIMAX MASTER_RAW CONVERTER_GX-10
36
-
4. Turn on the camera.
39
-
7. The upgrade starts as shown.
46
-
Writing the new firmware.......
47
-
3) Light source adjustment for digital adjustment
56
-
3-3. Setup the master body and standard lens
57
-
⑨ Click the [Calibration Mode] button.↓
59
-
■ Adjustment process
60
-
Ⅰ. OPS Unit Adjustment
62
-
① Set the AF lever to MF.
63
-
⑦ The following menu displays.
64
-
≪ When the T100 was changed ≫
65
-
Ⅱ. Adjustment of the Single Reflex part
67
-
22-1. Compter setup
68
-
② Do the adjustment as the following steps.
69
-
[CCD POSITION ADJUST] adjustment
70
-
□Battery adapter for 76830
71
-
22-5. Closing procedure
72
-
1. BV adjust (brightness value)
73
-
⑧ Click the 2. EXPOSURE ADJUST-BV ADJUST menu
76
-
⑨ Select a type of EV tester.
77
-
The changed data saves on the camera.
80
-
2. AF adjustment
83
-
If the result is green, it is correct.
90
-
Click the "Start" button on the Fucos menu tab.
92
-
2-2. Checking the AF sensor position
95
-
⑥ Click the 'end' button to close the program.
104
-
3. Focus adjustment
105
-
The temperature is saved on the camera.
108
-
3-2. HORIZONTAL focus adjustment
109
-
“OK”를 클릭해 조정한다.
110
-
Click the 'START' button.
111
-
Click the 'Close' button to close the window.
113
-
3-3. VERTICAL focus adjustment
114
-
The adjustment is complete. Click the 'OK' button.
117
-
3-4. AF shift adjustment
119
-
③ The [afs] button displays on the tool bar.
120
-
■ Checking process
121
-
4. BATTERY LEVEL ADJUST
122
-
Ⅲ. Adjustment for OPS gain
123
-
⑦ Fix the camera with 2 screws
125
-
4) Adjustment process
127
-
16. Turn off the controller.
131
-
1：Set the product's own information
132
-
② Set the mode dial to M.
133
-
⑩ Executing the adjustment
137
-
※ Information: Error message
139
-
Ⅴ. Shutter speed adjust
140
-
2) Camera setup
141
-
Shutter speed table
146
-
4) Adjustment process (Converting value)
147
-
④ Adjustment window displays.
148
-
2. Adjusting the metering sensor position
156
-
④ Remove the glue that holds 0-J100.
157
-
1. The order of assembly and disassembly
162
-
■ The order of body disassembly
163
-
2. A301 (Top cover)
164
-
⑦ Discharging the main condensor of the strobe
165
-
3．A150 / 201 (Front cover / Rear cover)
167
-
⑧ Loose the screw and remove the lug plate
168
-
⑨ Two screws
169
-
5．0-T100 (Main circuit block)
170
-
⑪ Three screws↓
171
-
※ OPS / CCD block
172
-
④ Two TY screw
173
-
⑤ Lift the O201 to the front as shown
174
-
8. A350 (Main SW part)
175
-
9．0-T700 (Top right relay circuit)
176
-
⑤ Two screws
177
-
10．0-T750 (Left top relay circuit)
178
-
④ Three screws
179
-
11．0-Q200 (Storbe circuit)
180
-
■ The order of body assembly
181
-
① Viewfinder lens part (M301•L7•etc.)
182
-
② SI block (M51, 0-M52, M53, L11, L12, 0-O170etc.)
183
-
4. [Adjustment] SI-LED position
184
-
① Set the Focus lever to CAF
187
-
6. 0-Q200 (strobe Circuit)
188
-
7. 0-T750 (Left top relay circuit)
189
-
⑤ Fix the RAW button SW part with the DT (5x5)
190
-
8. 0-T700 (Right top relay circuit)
191
-
⑤ Four soldering points of the T71 PCB
192
-
9. A350 (Main SW part)
193
-
⑤ Arrange the lead wires with the BT (6X15).
194
-
10. O201 (LCD block)
195
-
11. 0-T970 (SD circuit block)
196
-
12. 0-T100 (Main circuit block)
197
-
13. 0-T770 (PZ circuit block)
199
-
⑤ Four lead wires
200
-
15. 0-A51 (Tripod holder)
201
-
17. [Adjustment] SR adjustment
203
-
[Cautions of the sealing assembly]
207
-
⑨ A150 …Set the Focus lever to MF.
209
-
③ Five lead wires
210
-
⑤ A173(TY screw 1.7x6.0, 2EA)
211
-
⑧ CNL-D1.7x5.5…Open the rubber
212
-
22. [Adjustment] Single Reflex part
213
-
23. [Adjustment] SR Gain adjustment
214
-
27. [Check] Function check (Final checking)
216
-
③ Select Tv8 (1/8 sec.)
217
