Sarabec Crescendo 60 Manuals

crescendo 60 Personal Listening System a Operating Instructions Introduction Thank you for choosing the Crescendo 60 personal listening system. Before using the system, please read these operating instructions to benefit from all the capabilities of the system and it will give you many hours of reliable listening performance. The Crescendo 60 will help you to communicate with confidence. It is a battery powered amplifier that can receive sound from various sources, and then amplify that sound to the way you like to listen. The Crescendo 60 has a wide-ranging tone control that can boost the high and low frequencies according to your hearing needs. There are options enabling you to use the system with or without a hearing aid. Precautions WARNING The sound input from this system can be very high: Switch off before changing the batteries or plugging or unplugging any accessories. The manufacturer cannot be held responsible for damage caused by not using the Crescendo 60 in accordance with these safety precautions. Do not open the casing of the Crescendo 60 except to change batteries or operate the mode switch. No user-serviceable parts can be found inside. Ensure mains powered equipment is switched off before connecting to the Crescendo 60. Do not expose the Crescendo 60 to rain or any other forms of moisture. Do not expose the Crescendo 60 to direct sunlight or extreme heat such as radiators. Only AA batteries of the type specified can be used. Do not mix old and new batteries. Use rechargeable batteries in accordance with the instructions supplied with them. If the Crescendo 60 is not to be used for a long time, remove the batteries. Product Overview INPUT MODE SWITCH � Rotary Volume control. � Rotary Tone control. � Belt clip. � Neck cord. � Uses 2 X AA alkaline batteries giving over 60 hours of use with a headset � Rechargeable batteries can be used. � Battery life will depend on battery capacity. � Power On/Low battery light � Input selection mode switch (Microphone, Aux, T/Loop) MICROPHONE SOCKET HEADPHONE SOCKET VOLUME CONTROL TONE CONTROL POWER ON LIGHT Inserting Batteries The unit uses 2 AA alkaline batteries (LR6 or AA). Remove belt clip if fitted (see below). Remove the battery cover located on the rear of the amplifier by pressing in the clip on the end of the unit and lifting the cover upward. Press on clip and lift up to release battery cover Insert the two batteries according to the symbol shown in the battery compartments. Replace the battery cover. Basic Operation The Crescendo 60 is delivered set for microphone use. Insert batteries as above. With the amplifier switched off, check volume control is turned to left until click felt. Control will point upwards and power light will be off. Plug a microphone into the microphone socket with the microphone symbol. Plug either headphones or neck loop (for hearing aid users with loop facility) into the headphone socket with the headphone symbol. Wear the headphones or neck loop. Switch the amplifier on. Turn the volume control clockwise past the “click”. A green LED will light up to indicate the amplifier is on. When colour changes to red the batteries are coming to the end of their useful life. Adjust the volume to suit your listening level and the tone control to boost the high or low tones to adjust clarity. When finished turn the amplifier off by turning the volume control anti-clockwise until it “clicks”. The green LED will go out.

crescendo 60 Personal Listening System a Operating Instructions Introduction Thank you for choosing the Crescendo 60 personal listening system. Before using the system, please read these operating instructions to benefit from all the capabilities of the system and it will give you many hours of reliable listening performance. The Crescendo 60 will help you to communicate with confidence. It is a battery powered amplifier that can receive sound from various sources, and then amplify that sound to the way you like to listen. The Crescendo 60 has a wide-ranging tone control that can boost the high and low frequencies according to your hearing needs. There are options enabling you to use the system with or without a hearing aid. Precautions WARNING The sound input from this system can be very high: Switch off before changing the batteries or plugging or unplugging any accessories. The manufacturer cannot be held responsible for damage caused by not using the Crescendo 60 in accordance with these safety precautions. Do not open the casing of the Crescendo 60 except to change batteries or operate the mode switch. No user-serviceable parts can be found inside. Ensure mains powered equipment is switched off before connecting to the Crescendo 60. Do not expose the Crescendo 60 to rain or any other forms of moisture. Do not expose the Crescendo 60 to direct sunlight or extreme heat such as radiators. Only AA batteries of the type specified can be used. Do not mix old and new batteries. Use rechargeable batteries in accordance with the instructions supplied with them. If the Crescendo 60 is not to be used for a long time, remove the batteries. Product Overview INPUT MODE SWITCH � Rotary Volume control. � Rotary Tone control. � Belt clip. � Neck cord. � Uses 2 X AA alkaline batteries giving over 60 hours of use with a headset � Rechargeable batteries can be used. � Battery life will depend on battery capacity. � Power On/Low battery light � Input selection mode switch (Microphone, Aux, T/Loop) MICROPHONE SOCKET HEADPHONE SOCKET VOLUME CONTROL TONE CONTROL POWER ON LIGHT Inserting Batteries The unit uses 2 AA alkaline batteries (LR6 or AA). Remove belt clip if fitted (see below). Remove the battery cover located on the rear of the amplifier by pressing in the clip on the end of the unit and lifting the cover upward. Press on clip and lift up to release battery cover Insert the two batteries according to the symbol shown in the battery compartments. Replace the battery cover. Basic Operation The Crescendo 60 is delivered set for microphone use. Insert batteries as above. With the amplifier switched off, check volume control is turned to left until click felt. Control will point upwards and power light will be off. Plug a microphone into the microphone socket with the microphone symbol. Plug either headphones or neck loop (for hearing aid users with loop facility) into the headphone socket with the headphone symbol. Wear the headphones or neck loop. Switch the amplifier on. Turn the volume control clockwise past the “click”. A green LED will light up to indicate the amplifier is on. When colour changes to red the batteries are coming to the end of their useful life. Adjust the volume to suit your listening level and the tone control to boost the high or low tones to adjust clarity. When finished turn the amplifier off by turning the volume control anti-clockwise until it “clicks”. The green LED will go out.

DE EN Operation Instructions FR Mode d’emploi NL Gebruiksaanwijzing Hörverstärker Amplificateur d’écoute Personal Listening System Hoorversterker Seite 2 Pagina 50 Page 34 Page 18 IT Istruzioni per l’uso ES Instrucciones de operación Amplificatore Sistema de comunicación personal Página 82 Pagina 66 Bedienungsanleitung »Crescendo 60«