Sealey AK2946 Manuals

Portable and lightweight torch with piezoelectric start. Features adjustable heating control ranging up to 450°C (approximately). Removable solder tip transforms torch into burning flame heat source. Supplied with a variety of nozzles for various applications including a flameless heat source adaptor. Safety cap for storage. Sponge cleaning tray and small roll of solder wire. Suitable for heating, soldering and shrinking. Powered by Butane (lighter fluid). AK2946 Kit comprises: Butane Solder Torch, Soldering Head with 3 Solder Tips, Spanner for solder tips, Curved deflector plate, Hot Knife, Sponge, Safety Cap. Thank you for purchasing a Sealey Product. Manufactured to a high standard this tool will, if used according to these instructions and properly maintained, give years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE. INSTRUCTIONS FOR: BUTANE SOLDERING/HEATING TORCH KIT MODEL: AK2946 1. SAFETY INSTRUCTIONS 3. OPERATING INSTRUCTIONS AK2946 - 1 - 18/06/07 ! WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using the torch. " Familiarise yourself with the application and limitations, as well as the potential hazards, peculiar to the torch. " Butane gas is highly flammable, so keep an appropriate fire extinguisher close to hand. ! WARNING! Use and handle the butane gas (lighter fuel) in accordance with the instructions supplied with the fuel. " Keep the work area clean, uncluttered and ensure there is adequate ventilation and lighting. " Keep children and unauthorised persons away from the working area. " Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain and/or tie back long hair. " Point the torch away from yourself and others when igniting flame. " Keep hands and body clear of the torch head when operating as it becomes very hot. " Secure unstable workpiece with a clamp, vice or other adequate holding device. # DO NOT get the torch wet. # DO NOT use torch where there are flammable liquids, solids or gases such as paint solvents and including waste wiping or cleaning rags etc. # DO NOT use the torch for any purpose other than for which it is designed. # DO NOT use accessories other than those supplied with the torch. ! WARNING! DO NOT touch the torch head during, or immediately after, use. Allow the torch to cool naturally before handling it or returning it to its storage case. # DO NOT cool the torch in water. # DO NOT point the torch at yourself, others, or animals. # DO NOT operate the torch when you are tired, or under the influence of alcohol, drugs or intoxicating medication. # DO NOT allow untrained persons to operate the torch. # DO NOT operate the torch if any parts are damaged or missing as this may cause failure and/or personal injury. # DO NOT touch the workpiece close to the heated area as it will be very hot. Allow to cool. # DO NOT leave the torch, after use, until it has cooled. " When work is complete, allow the torch to cool. Clean the torch and accessories, return to case and store in a safe, dry childproof location. # DO NOT store in direct sunlight or where the temperature could exceed 104OF/40OC ! WARNING! Failure to use the torch correctly may result in fire, damage and/or personal injury. $ DANGER! The flame is invisible in sunlight - be extremely cautious. ! WARNING! Ensure you have read and understood the safety instructions in Section 1 before using the torch. Note: The torch is supplied without butane gas. Before use it must be fuelled as follows: 3.1. TO FUEL THE TORCH 3.1.1. Use only high quality butane gas (lighter fuel) to fill the torch. 3.1.2. Ensure the ‘On/Off’ switch is in the ‘Off’ position. See fig.3, ‘Gas On/Off Switch’. 3.1.3. Follow the instructions on the butane fuel can. 3.1.4. Apply the can filler tip to the torch base filler valve (fig.1). Use a pumping action for best filling results. 3.1.5. Once full, allow gas in the torch to stand and stabilise for a few minutes before use. fig. 1 2. INTRODUCTION fig. 2

Portable and lightweight torch with piezoelectric start. Features adjustable heating control ranging up to 450°C (approximately). Removable solder tip transforms torch into burning flame heat source. Supplied with a variety of nozzles for various applications including a flameless heat source adaptor. Safety cap for storage. Sponge cleaning tray and small roll of solder wire. Suitable for heating, soldering and shrinking. Powered by Butane (lighter fluid). Kit comprises: Butane Solder Torch, Soldering Head with 3 Solder Tips, Spanner for Solder Tips, Curved Deflector Plate, Hot Knife, Sponge and Safety Cap. Thank you for purchasing a Sealey Product. Manufactured to a high standard this tool will, if used according to these instructions and properly maintained, give years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE. INSTRUCTIONS FOR: BUTANE SOLDERING/HEATING TORCH KIT MODEL No: AK2946 1. SAFETY INSTRUCTIONS 3. OPERATING INSTRUCTIONS � WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using the torch.  Familiarise yourself with the application and limitations, as well as the potential hazards, peculiar to the torch.  Butane gas is highly flammable, so keep an appropriate fire extinguisher close to hand.  WARNING! Use and handle the butane gas (lighter fuel) in accordance with the instructions supplied with the fuel.  Keep the work area clean, uncluttered and ensure there is adequate ventilation and lighting.  Keep children and unauthorised persons away from the working area.  Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain and/or tie back long hair.  Point the torch away from yourself and others when igniting flame.  Keep hands and body clear of the torch head when operating as it becomes very hot.  Secure unstable workpiece with a clamp, vice or other adequate holding device.  DO NOT get the torch wet.  DO NOT use torch where there are flammable liquids, solids or gases such as paint solvents and including waste wiping or cleaning rags etc.  DO NOT use the torch for any purpose other than for which it is designed.  DO NOT use accessories other than those supplied with the torch.  WARNING! DO NOT touch the torch head during, or immediately after, use. Allow the torch to cool naturally before handling it or returning it to its storage case.  DO NOT cool the torch in water.  DO NOT point the torch at yourself, others, or animals.  DO NOT operate the torch when you are tired, or under the influence of alcohol, drugs or intoxicating medication.  DO NOT allow untrained persons to operate the torch.  DO NOT operate the torch if any parts are damaged or missing as this may cause failure and/or personal injury.  DO NOT touch the workpiece close to the heated area as it will be very hot. Allow to cool.  DO NOT leave the torch, after use, until it has cooled.  When work is complete, allow the torch to cool. Clean the torch and accessories, return to case and store in a safe, dry childproof location.  DO NOT store in direct sunlight or where the temperature could exceed 104°F/40°C  WARNING! Failure to use the torch correctly may result in fire, damage and/or personal injury. � DANGER! The flame is invisible in sunlight - be extremely cautious.  WARNING! Ensure you have read and understood the safety instructions in Section 1 before using the torch. Note: The torch is supplied without butane gas. Before use it must be fuelled as follows: 3.1. TO FUEL THE TORCH 3.1.1. Use only high quality butane gas (lighter fuel) to fill the torch. 3.1.2. Ensure the ‘On/Off’ switch is in the ‘Off’ position. See fig.3, ‘Gas On/Off Switch’. 3.1.3. Follow the instructions on the butane fuel can. 3.1.4. Apply the can filler tip to the torch base filler valve (fig.1). Use a pumping action for best filling results. 3.1.5. Once full, allow gas in the torch to stand and stabilise for a few minutes before use. Note: Before refilling, ensure that the filler valve and the probe on the can of lighter fluid are clean and free from dirt and debris. Check that the correct filling adaptor is fitted to the lighter fluid refill can. Ensure that the torch and the can of lighter fluid is at room temperature before commencing refill. Lighter fluid is highly flammable – refill in a well ventilated place, away from any sources of ignition. Fill in conjunction with the operating and safety instructions found on the can of lighter fluid. If any spillages occur during the refilling process, allow plenty of time for escaped gas to evaporate before allowing sources of ignition in the vicinity. Once full, check the torch for leaks by listening for a hissing noise. If the hissing persists, do not ignite and remove the torch to a well ventilated area until the gas has escaped – do not allow any ignition in the vicinity of the tool. fig.1 2. INTRODUCTION fig.2 Original Language Version AK2946 Issue: 2 - 09/08/11

BUTANE HEATING / SOLDERING TORCH KIT MODEL NO: AK2946 Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE. 1. SAFETYi � WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment. � WARNING! Always wear approved eye or face protection when operating the torch. � WARNING! Butane gas is extremely flammable, handle with care. � WARNING! Always point the torch away from the eyes, body or flammable objects when igniting and during operation. � WARNING! Ensure the Gas Controller Knob is firmly closed and the flame completely extinguished after use. � WARNING! DO NOT puncture the cartridge or dispose of in a fire. � Use only specified gas (Sealey Gas Charger Butane SCS035S) 8 DO NOT use the torch in an area where paint fumes, solvents or other flammable solids, liquids or gases pose a potential hazard. 9 Keep flammable material away from the torch when operating. Flammable waste, such as wiping or cleaning rags, must be placed in a closed metal container and disposed of correctly. 8 DO NOT operate the torch when you are tired or under the influence of alcohol, drugs or intoxicating medication. 8 DO NOT hold the workpiece by hand. Use clamps or a vice (not included) to secure the workpiece. 8 DO NOT operate the torch if any parts are damaged or missing as this may cause failure and/or possible personal injury. 8 DO NOT touch the workpiece close to the heated area as it will be very hot. Allow to cool. 8 DO NOT touch the burner tube during or immediately after use as it will be very hot. Allow to cool. 8 DO NOT leave the torch operating unattended. 8 DO NOT allow children to operate the torch. 9 Disconnect the gas cartridge when not in use. Store cartridge away from direct sunlight in a safe, dry, childproof area, where the temperature will not exceed 40°C (104°F). 9 After use, allow the torch to cool before storing it. IMPORTANT! Observe cautions on the gas refill cartridge label. 2. INTRODUCTION Portable and lightweight torch with piezoelectric start. Features adjustable heating control ranging up to 450°C (approximately). Removable solder tip transforms torch into burning flame heat source. Includes a variety of nozzles for various applications including a flameless heat source adaptor. Safety cap for storage. Sponge cleaning tray and small roll of solder wire. Suitable for heating, soldering and shrinking. Powered by Butane (lighter fuel). Supplied in storage case. 3. SPECIFICATION Model No.:................................................................AK2946 Sealey Gas Charger Butane .................................. SCS035S Contents: Deflector, soldering head, soldering tips (small, medium, large), hot knife, spanner. 4. OPERATION � WARNING! Ensure you have read and understood the safety instructions in Section 1 before using the torch. NOTE: The torch is supplied without butane gas. Before use it must be fuelled as follows: 4.1. TO FUEL THE TORCH 4.1.1. Use only high quality butane gas (lighter fuel) to fill the torch. 4.1.2. Ensure the ‘On/Off’ switch is in the ‘Off’ position. See fig.3, ‘Gas On/Off Switch’. 4.1.3. Follow the instructions on the butane fuel can. 4.1.4. Apply the can filler tip to the torch base filler valve (fig.1). Use a pumping action for best filling results. 4.1.5. Once full, allow gas in the torch to stand and stabilise for a few minutes before use. NOTE: Before refilling, ensure that the filler valve and the probe on the can of lighter fluid are clean and free from dirt and debris. Check that the correct filling adaptor is fitted to the lighter fluid refill can. Ensure that the torch and the can of lighter fluid is at room temperature before commencing refill. Lighter fluid is highly flammable – refill in a well ventilated place, away from any sources of ignition. Fill in conjunction with the operating and safety instructions found on the can of lighter fluid. If any spillages occur during the refilling process, allow plenty of time for escaped gas to evaporate before allowing sources of ignition in the vicinity. AK2946 Issue 3 (H, F) 28/05/19 Original Language Version © Jack Sealey Limited Refer to instruction manual Wear protective gloves Wear eye protection Warning: hot surfaces