Sealey ASC70 Manuals

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. WARNING! DO NOT OVERLOAD AXLE STANDS BEYOND RATED CAPACITY. OVERLOADING CAN CAUSE DAMAGE TO, OR FAILURE OF, THE AXLE STANDS. POSITION LOAD ON CENTRE OF SADDLE. ALWAYS USE STANDS IN PAIRS ON HARD LEVEL SURFACE CAPABLE OF SUSTAINING THE LOAD. USE OF STANDS ON OTHER THAN HARD LEVEL SURFACES CAN RESULT IN LOAD INSTABILITY AND POSSIBLE LOSS OF LOAD. DO NOT USE ON TARMACADAM. FAILURE TO FOLLOW THESE INSTRUCTIONS, MAY RESULT IN DAMAGE TO AXLE STANDS, LOSS OF LOAD RESULTING IN PROPERTY DAMAGE, SERIOUS PERSONAL INJURY OR LOSS OF LIFE. � Ensure the axle stands are assembled complete and all fixings are secured. DO NOT use if any component is damaged. � Raise the sprung assisted centre column of the axle stand and ensure the centre of the saddle is located under a structurally sound vehicle jacking point. Refer to the vehicle handbook for jacking points. � WARNING! Caution required when removing the centre column retaining pin; internal spring forces will be encountered. ▲ DANGER! Great care must be taken to ensure you lower the vehicle slowly and carefully onto the centres of all the axle stands simultaneously. Acheived using the fine adjusters.  Ensure that the vehicle and stands are stable before starting work.  DO NOT use on soft ground or tarmacadam. Use on horizontal concrete only. � Use a minimum of four stands to support and stabilise a vehicle, and a minimum of two additional stands for each additional axle.  DO NOT support more than the maximum capacity, as written on the axle stand, (i.e. 14 tonnes per pair etc.).  DO NOT apply side horizontal forces to the vehicle while supported by the stands.  DO NOT start the engine while the vehicle is supported by the stands. � Use only supplied attachments, restraints or adaptors supplied by the manufacturer. N.B. IN ORDER TO OBTAIN THE CAPACITIES SHOWN, THE VEHICLE MUST BE EVENLY SUPPORTED BY THE STANDS. Original Language Version ASC70 Issue: 1 - 01/12/15 Heavy-duty high level axle stand to safely support vehicle for extended period of time. Independently UK load tested. Supplied with three interchangeable crutches for even load support. Heavy gauge steel frame and welded construction give superior strength and safety. Features captive, spring assisted, multi-position pin load support and castors for easy manoeuvrability. Ideal for commercial vehicles. Sold as singles. Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ASC70 Capacity Each: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7tonne Capacity Pair: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14tonne Minimum Height:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1295mm Maximum Height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1905mm © Jack Sealey Limited 1. SAFETY INSTRUCTIONS FOR: HIGH LEVEL AXLE STAND 7TONNE CAPACITY - COMMERCIAL USE MODEL NO: ASC70 Refer to instruction manual 2. INTRODUCTION 3. SPECIFICATION 4. CONTENTS �� WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be applied by the operator. Item Description Qty 1 Central Column Sub Assembly 1-set 2a,b,c Saddles 1-set 3 Tripod Leg 3 4 Swivel Castor Sub Assembly 3 5 Cross Members 3 6 Bracket 3 7 Hexagon Screw M12 X 40 9 8 Hexagon Bolt M12 X 75 3 9 Hexagon Nut M12 12 10 Plain Washer Ø12 24 11 Spring Washer Ø12 12 a b c Item 2