Sealey CD2013.V2 Manuals

INSTRUCTIONS FOR: CONVECTOR HEATER 2000W MODEL No's: CD2013.V2 1.2 GENERAL SAFETY  WARNING! Disconnect the heater from the mains power supply before carrying out any servicing or maintenance.  Disconnect the heater from the power supply before handling or cleaning.  Maintain the heater in good order and clean condition for best and safest performance.  Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.  Ensure there is adequate lighting and keep the immediate area in front of the outlet grille clear.  Only use the heater standing on its feet in the upright position.  DO NOT allow any untrained or incompetent persons to use the heater. Ensure they are familiar with the controls and hazards of the heater.  DO NOT let power lead hang over an edge (i.e. table), or touch a hot surface, lie in heater hot air flow, or run under a carpet.  DO NOT touch the outlet grille (top) of the heater during and immediately after use as it will be hot.  DO NOT place the heater near items that may be damaged by heat.  DO NOT allow children to touch or to operate the heater.  DO NOT place heater too close to yourself or any object, allow the air to circulate freely.  DO NOT use the heater for any purpose other than for which it is designed.  DO NOT use heater on very deep pile carpets.  DO NOT use the heater out of doors. This heater is designed for indoor use only.  DO NOT use heater if the power cord, plug or the heater is damaged, or if the heater has become wet.  DO NOT use in bathroom, shower room, or in any wet or damp environments or where there is high condensation.  DO NOT operate the heater when you are tired or under the influence of alcohol, drugs or intoxicating medication.  DO NOT allow the heater to get wet as this may result in an electric shock and personal injury.  DO NOT insert or allow objects to enter any openings of heater as this may cause an electric shock,a fire or damage to heater. 1.1. ELECTRICAL SAFETY  WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following: You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer. You must also read and understand the following instructions concerning electrical safety. 1.1.1. The Electricity at Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year. 1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician. 1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2. and use a Portable Appliance Tester. 1.1.4. Ensure that cables are always protected against short circuit and overload. 1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that none is loose. 1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply to be used and that the plug is fitted with the correct fuse - see fuse rating at right. 1.1.7. DO NOT pull or carry the appliance by the power cable. 1.1.8. DO NOT pull the plug from the socket by the cable. 1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty item repaired or replaced by a qualified electrician. When an ASTA/BS approved UK 3 pin plug is damaged, cut the cable just above the plug and dispose of the plug safely. Fit a new plug according to the following instructions (UK only). a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’. b) Connect the BROWN live wire to the live terminal ‘L’. c) Connect the BLUE neutral wire to the neutral terminal ‘N’. d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulation extends beyond the cable restraint and that the restraint is tight. 1.1.10. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that the capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use of 2.5mm² section cable. REPLACEMENT FUSE RATING:13A IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE. Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions and maintained properly, give you years of trouble free performance. Refer to Instruction Manual Warning: Hot Surface Indoor Use Only 1. SAFETY Original Language Version CD2013.V2 Issue: 1 - 25/07/17 © Jack Sealey Limited