Sealey RE2280 Manuals

INSTRUCTIONS FOR COIL Spring Compressor MODEL: RE2280 Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.  DANGER! Stop compressing the spring before the coil windings touch.  WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.  WARNING! Wear approved safety eye protection (standard spectacles are not adequate).  WARNING! Measure the outer diameter of the spring to be compressed and select the correct set of jaws to fit the spring.  DO NOT operate spring compressor if parts are damaged or missing as this may cause failure and/or personal injury.  DO NOT force the spring compressor to achieve a task it is not designed to perform.  DO NOT allow untrained persons to use the spring compressor.  Familiarise yourself with the applications, limitations and potential hazards of the spring compressor.  Maintain the spring compressor in good condition. Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.  Keep the work area clean, uncluttered and ensure there is adequate lighting.  Keep hands and body clear of the spring when operating the spring compressor.  Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.  Remove ill fitting clothes. Remove ties, watches, rings, other loose jewellery. Contain and/or tie back long hair.  Wear appropriate protective clothing.  When not in use clean and store the spring compressor in a safe, dry, childproof location. 2. TECHNICAL SPECIFICATION 1. SAFETY INSTRUCTIONS Maximum Spring Load:....................................1250kg Size/Suitability:.............................. (Ø80mm - 135mm) Jaw Opening:............................................115-300mm Drive:.......................................................... 19mm Hex 3. INTRODUCTION 3.1. Designed for use on wishbone suspension using access points in the rear suspension arm. Features two pairs of carefully shaped yokes that prevent the coil spring from bowing. Saves time over traditional methods of demounting springs. Fig.1 Original Language Version RE2280 Issue: 1 - 7/6/10 all-guides com

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE. 1. SAFETY ▲ DANGER! Stop compressing the spring before the coil windings touch. � WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment. � WARNING! Wear approved safety eye protection (standard spectacles are not adequate). � WARNING! Measure the outer diameter of the spring to be compressed and select the correct set of jaws to fit the spring. 8 DO NOT operate spring compressor if parts are damaged or missing as this may cause failure and/or personal injury. 8 DO NOT force the spring compressor to achieve a task it is not designed to perform. 8 DO NOT allow untrained persons to use the spring compressor. 9 Familiarise yourself with the applications, limitations and potential hazards of the spring compressor. 9 Maintain the spring compressor in good condition. 9 Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty. 9 Keep the work area clean, uncluttered and ensure there is adequate lighting. 9 Keep hands and body clear of the spring when operating the spring compressor. 9 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes. 9 Remove ill fitting clothes. Remove ties, watches, rings, other loose jewellery. Contain and/or tie back long hair. 9 Wear appropriate protective clothing. 9 When not in use clean and store the spring compressor in a safe, dry, childproof location. 2. INTRODucTION Designed for use on wishbone suspension using access points in the rear suspension arm. Features two pairs of carefully shaped yokes that prevent the coil spring from bowing. Saves time over traditional methods of demounting springs. 3. SpEcIFIcATION Model no: ............................................................RE2280.V2 Maximum Spring Load: .................................................1250kg Size/Suitability: ........................................... (Ø80mm - 135mm) Jaw Opening: .........................................................115-300mm Drive: ....................................................................... 19mm Hex Refer to instruction manual Wear eye protection Fig.1 RE2280.V2| Issue:1 09/01/17 Original Language Version © Jack Sealey Limited InStRUCtIOnS FOR: TElEScOpIc SpRING cOMpRESSOR WIShbONE SuSpENSION 1250KG MODEL nO: RE2280.V2