Sealey SA1002 Manuals

MINI AIR RATCHET WRENCH 3/8” SQ. DRIVE MODEL NO: SA1002 Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE. 1. SAFETY 9 Follow all workshop safety rules, regulations, and conditions when using wrench. ‰ WARNING! Disconnect from air supply before changing accessories or servicing. ‰ WARNING! DO NOT use wrench if damaged or thought to be faulty. Contact Service Agent. ‰ WARNING! Check correct air pressure is maintained and not exceeded. We recommend 80psi. 9 Maintain the wrench in good condition and replace any damaged or worn parts. Use genuine parts only. Un-authorised parts may be dangerous and will invalidate the warranty. 9 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure. 9 Wear approved safety eye/face shield, ear defenders and hand protection. 9 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes. 9 Keep children and non essential persons away from the working area. 8 DO NOT use the wrench for a task it is not designed to perform. 8 DO NOT use wrench unless you have been instructed in its use by a qualified person. 8 DO NOT carry the wrench by the air hose, or yank the hose from the air supply. 8 DO NOT operate wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication. 8 DO NOT carry wrench with your hand on power trigger, in order to avoid unintentional starting. 8 DO NOT direct air from the air hose at yourself or others. 9 When not in use disconnect from air supply and store in a safe, dry, childproof location. ‰ WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be applied by the operator. 2. i INTRODUCTION Textured finish to ensure a good grip. Mini design for working in confined areas, ideal for working around engines where space is limited. Fitted with a twist reverse action and trigger operated power control. Features rear exhaust with baffle for reduced noise level. Suitable for professional workshop use. 3. i SPECIFICATION Model No:.................................................................. SA1002 Drive:.......................................................................... 3/8”Sq Maximum Torque:..........................................................34Nm Free Speed:................................................................420rpm Air Consumption:............................... ..........................8.5cfm Operating Pressure:....................................................... 80psi Inlet Size:...................................................................1/4”BSP Length:...................................................................... ..120mm Noise Power:..................................................................91dB Noise Pressure:..............................................................80dB Vibration:................................................................. 0.996m/s² Uncertainty:............................................................. 0.594m/s² 4. AIR SUPPLY 4.1. AIR SUPPLY (Recommended hook-up procedure is shown in fig.2.) 4.1.1. Ensure wrench air valve (or trigger) is in the “off” position before connecting to the air supply. 4.1.2. You will require an air pressure of 80psi, and an air flow according to specification. ‰ WARNING! Ensure the air supply is clean and does not exceed 80psi while operating the wrench. Too high an air pressure and/or unclean air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury. 4.1.3. Drain the compressor air tank daily. Water in the air line will damage the wrench. 4.1.4. Clean compressor air inlet filter weekly. Original Language Version © Jack Sealey Limited Refer to instruction manual Wear protective gloves Wear eye protection Wear face mask Wear ear protection SA1002 Issue 2 (3) 13/01/20