SICK RFU630-041 Series Manuals

Q U I C K S T A R T e n 1 About this document The purpose of this Quickstart is to allow you to commission the RFU630-041xx RFID read/write device (UHF) quickly and easily and to achieve initial read results with transponders. The Quickstart is valid for the regional radio variants listed in the “Device overview” section: see Device overview, page 7. In the following, the Quickstart refers to the RFU630-041xx (UHF) RFID read/write device simply as “device”. If variants are to be differentiated in the regional assignment, the respective device name RFU630-041xx is specified (xx = regional assignment). The Quickstart describes the commissioning process for an application with one device in an ambient temperature range 0 °C to +60 °C. Commissioning is carried out as an example for the RFU630-04100 device vari‐ ant (Europe region and other countries if necessary, see Device overview, page 7. The basis is the basic parameter setting of the device. The optional CDB650-204 connection module handles the industrial-standard signal distribu‐ tion for the device. Other connection modules are available. All rights reserved. Subject to change without notice. Supplementary documents Information, such as application examples and downloads of associated docu‐ ments (e.g. operating instructions) and software, can be found on the SICK prod‐ uct page on the Internet at: www.sick.com/RFU63x. For an overview see Sources for obtaining more information, page 8 in this Quickstart. More detailed information on mounting and electrically installing the device as a stand-alone unit than provided in this Quickstart is available in the RFU630-041xx RFID read/write device (UHF) operating instructions. The operating instructions add the following information to the Quickstart: • Requirements and notes for mounting and electrical installation at operating ambient temperatures below 0 °C • For applications in widely distributed systems: Notes on the suppression of ground potential equalizing currents 2 Safety information • This chapter is dedicated to the safety of commissioning personnel and the operator of the system in which the device is integrated. • Read this Quickstart carefully to familiarize yourself with the device and its functions before commissioning the device. The Quickstart is considered a part of the device and must be kept in an accessible location in the immedi‐ ate vicinity of the device at all times! • The radiated power of the external antenna(s) used must not exceed the maximum value permitted for each specific country, see Technical data, page 5 and see Device overview, page 7. Electromagnetic radiation WARNING Health hazard as a result of high-frequency electromagnetic radiation! The RFU630-04100 (Europa/South Africa region and possibly other countries) is designed for operation in accordance with ETSI EN 302208. During opera‐ tion with the external RFA630-x00 antenna(s), the human exposure regulations covered by EN 50364 must be observed. b Limit human exposure to electromagnetic fields. Suitable safety dis‐ tances must be maintained during both short-term and long-term work in the radiation range of the external antenna(s). Minimum distances to be maintained between the antenna and the human body during long-term transmission according to ETSI: ° 30 cm at maximum antenna radiation power of 2 W ERP ° 15 cm at reduced radiation power of 1 W ERP ° 10 cm at radiation power of 0.5 W ERP The RFU630-04101 (USA/Canada region and possibly other countries) satis‐ fies the limit values of the FCC for exposure to radiation in an uncontrolled environment. b During operation with external RFA630-x01 antenna(s), a safety distance of at least 30 cm must be maintained between the antenna and the human body. Complete region assignment of the RFU630-041xx see Device overview, page 7. Prerequisites for enclosure rating IP • To comply with the IP67 enclosure rating in operation, the following require‐ ments must be met. If this is not done, the device does not fulfill any speci‐ fied IP enclosure rating. ° The side cover for both the USB female connector and the microSD card slot must be screwed tight to the device. Recommended tightening torque for the cover screws: 40 Ncm ± 5 Ncm. ° The SICK cables plugged into the M12 and TNC connections must be screwed tight. ° Any electrical connections that are not being used must be fitted with protective caps or plugs that are screwed tight (as in the delivery condi‐ tion). ° Any electrical connections for external antennas (TNC reverse) that are not being used must be fitted with screw-on protective caps (as in the delivery condition). ° Only operate the device without a cover for a short period while insert‐ ing or removing the memory card or temporarily using the USB inter‐ face. During this time, protect the device against moisture and dust. • Opening the screws of the device housing will invalidate any warranty claims against SICK AG. For further warranty provisions, see the General Terms and Conditions of SICK AG, e.g. on the delivery note of the device. Standard IP technology NOTE SICK uses standard IP technology in its products. The emphasis is placed on availability of products and services. SICK always assumes the following prerequisites: • The customer ensures the integrity and confidentiality of the data and rights affected by its own use of the aforementioned products. • In all cases, the customer implements the appropriate security measures, such as network separation, firewalls, virus protection, and patch management. 2.1 Intended use The RFU630-041xx is an intelligent RFID read/write device (UHF) from the RFU63x product family. The stationary device automatically identifies wireless- based data cards (transponders) on stationary and moving objects. The device also supports data card management. The device is a compact read and write unit that uses a maximum of 4 external antennas to process all current, passive transponders in accordance with ISO/IEC 18000-6C and EPCglobal UHFC1G2 in the regionally-dependent UHF car‐ rier frequency range. The device does not contain any integrated antennas. Intelligent process logic enables processing either as a stand-alone solution or as part of a group in a network. The device sends the read results to a higher-level computer via its host interface. The computer coordinates further processing. The device receives corresponding commands for data card management (write, read, etc.) via its host interface. Device variants refer to the region assignment (operating permit and carrier fre‐ quency range), see Device overview, page 7. NOTE The device approval was granted for a specific region. The region assignment cannot be changed. • Only use the device in the region and the country for which it has been approved. • When reselling the device, inform the buyer of the fixed region assign‐ ment. • Should the device be passed on to a third party, these operating instruc‐ tions and the Quickstart should be handed over with it. • For country-specific particulars to consider when operating the device, see Operational restrictions, page 7. Intended use of the device also includes compliance with all information in this Quickstart. 3 Device description 3.1 Device view Dimensional drawing of the RFU63x-041xx, unit: mm (inch), decimal separator: period: A Dimensions of the threaded mounting holes of the RFU630-041xx, unit: mm (inch), decimal separator: period: B 3.2 Status displays Figure 1: Status indicators on the first display level Status displays Advertisement LED Color Status Ready Lights up Green The device is ready for use. Lights up Red The device is not ready for use: hardware fault 8015215/10QY/2019-09-02/en RFU630-041xx | SICK 1 8015215/10QY/2019-09-02 www.sick.com RFU630-041xx SICK AG Erwin-Sick-Straße 1 D-79183 Waldkirch

Q U I C K S T A R T e n 1 About this document The purpose of this Quickstart is to allow you to commission the RFU630-041xx RFID read/write device (UHF) quickly and easily and to achieve initial read results with transponders. The Quick Start Guide is valid for all the regional radio device variants listed: see Device overview, page 7. In the following, the Quick Start Guide refers to the RFU630-041xx (UHF) RFID read/write device simply as “device”. If variants are to be differentiated in the regional assignment, the respective device name RFU630-041xx is specified (xx = regional assignment). The Quickstart describes the commissioning process for an application with one device in an ambient temperature range 0 °C to +60 °C. Commissioning is carried out as an example for the RFU630-04100 device vari‐ ant (Europe region and other countries if necessary, see Device overview, page 7). The basis is the basic parameter setting of the device. The optional CDB650-204 connection module handles the industrial-standard signal distribu‐ tion for the device. Other connection modules are available. All rights reserved. Subject to change without notice. Supplementary documents Information, such as application examples and downloads of associated docu‐ ments (e.g. operating instructions) and software, can be found on the SICK prod‐ uct page on the Internet at: www.sick.com/RFU63x. For an overview see Sources for obtaining more information, page 8 in this Quickstart. More detailed information on mounting and electrically installing the device as a stand-alone unit than provided in this Quickstart is available in the RFU63x / 65x RFID read/write device (UHF) operating instructions. The operating instructions add the following information to the Quick Start Guide: • Requirements and notes for mounting and electrical installation at operating ambient temperatures below 0 °C • For applications in widely distributed systems: Notes on the suppression of ground potential equalizing currents • Electrical wiring plans for the CDB650-204 and CDM420-0006 connection modules in relation to the connected device 2 Safety information • This chapter is dedicated to the safety of commissioning personnel and the operator of the system in which the device is integrated. • Read this Quickstart carefully to familiarize yourself with the device and its functions before commissioning the device. The Quickstart is considered a part of the device and must be kept in an accessible location in the immedi‐ ate vicinity of the device at all times! • The radiated power of the external antenna(s) used must not exceed the maximum value permitted for each specific country, see Technical data, page 6 and Device overview, page 7. Electromagnetic radiation WARNING Health hazard as a result of high-frequency electromagnetic radiation! The RFU630-04100 device (Europa region and possibly other countries) is designed for operation in accordance with ETSI EN 302208. During operation with the external RFA630-x00 antennas (Europa region and possibly other countries), the human exposure regulations covered by EN 50364 must be observed. • Limit human exposure to electromagnetic fields. Suitable safety dis‐ tances must be maintained during both short-term and long-term work in the radiation range of the antennas. Minimum distances to be main‐ tained between the external antenna and the human body during long- term transmission: ° 30 cm at maximum antenna radiation power of 2 W ERP ° 15 cm at reduced radiation power of 1 W ERP ° 10 cm at radiation power of 0.5 W ERP The RFU630-04101 device (USA region and possibly other countries) satisfies the limit values of the FCC for exposure to radiation in an uncontrolled envi‐ ronment. • During operation with the external RFA630-x01 antennas (USA region and possibly other countries), a safety distance of at least 30 cm must be maintained between the antenna and the human body. Complete region assignment of the RFU630-041xx see Device overview, page 7. Conditions for specified enclosure rating • To ensure compliance with the IP67 enclosure rating of the device during operation, the following requirements must be met. If these requirements are not met, the device does not fulfill any specified enclosure rating. ° The joint side cover for the USB interface and the memory card slot is screwed tightly onto the device. Recommended tightening torque for the cover screws: 40 Ncm ± 5 Ncm. ° The cables plugged into the electrical M12 and TNC connections are screwed tight. ° Any unused M12 connections must be sealed with screw-on protective caps (for male connectors) or plugs (for female connectors) as sup‐ plied. ° Unused connections for external antennas must be sealed with metal screw-on protective caps as supplied. ° Only operate the device without a cover for a short period while insert‐ ing or removing the memory card or temporarily using the USB inter‐ face. During this time, protect the device against moisture and dust. • Opening the screws of the device housing will invalidate any warranty claims against SICK AG. For further warranty provisions, see the General Terms and Conditions of SICK AG, e.g. on the delivery note of the device. Standard IP technology NOTE SICK uses standard IP technology in its products. The emphasis is placed on availability of products and services. SICK always assumes the following prerequisites: • The customer ensures the integrity and confidentiality of the data and rights affected by its own use of the aforementioned products. • In all cases, the customer implements the appropriate security measures, such as network separation, firewalls, virus protection, and patch management. 2.1 Intended use The RFU630-041xx RFID read/write device is an intelligent 4Dpro sensor from the RFU6xx product family (UHF). Version (working range): Long Range. The stationary device automatically identifies wireless-based data cards (transponders) on stationary and moving objects. The device also supports data card management. The device is a compact read/write device that uses a maximum of 4 external antennas to process all current, passive transponders in accordance with ISO/IEC 18000-6C and EPCglobal UHFC1G2 in the regionally-dependent UHF car‐ rier frequency range. The device does not contain any integrated (internal) anten‐ nas. Intelligent process logic enables processing either as a stand-alone solution or as part of a group in a network. The device sends the read results to a higher-level computer via its host interface. The computer coordinates further processing of the data in the process. The device receives corresponding commands for data card management (write, read, etc.) via its host interface. Device variants refer to the region assignment, see Device overview, page 7. NOTE The device approval was granted for a specific region. The region assignment cannot be changed. • Only use the device in the region and the country for which it has been approved. • When reselling the device, inform the buyer of the fixed region assign‐ ment. • Should the device be passed on to a third party, these operating instruc‐ tions and the Quickstart should be handed over with it. • For country-specific particulars to consider when operating the device, see Operational restrictions, page 8 and see Connection of external UHF antennas, page 8. Intended use of the device also includes compliance with all information in this Quickstart and the supplementary RFU63x / 65x RFID read/write device (UHF) operating instructions. 8015215/Y737/2020-07-07/en RFU630-041xx | SICK 1 8015215/Y737/2020-07-07 www.sick.com RFU630-041xx SICK AG Erwin-Sick-Straße 1 D-79183 Waldkirch

T E C H N I C A L I N F O R M A T I O N RFU63x RFID WRITE/READ DEVICE (UHF)