Sigtronics SE-2 Manuals

Model SE-2 Headset Instructions The SE-2 series headset is adjusted at the factory for immediate use with all Sigtronics emergency apparatus intercoms and radio adapters in emergency vehicles. The headset is equipped with a single plug and a coiled cord. The head strap is adjustable so you may custom fit the headset. Place the headset over your head and adjust the strap until minimum pressure is felt on the top of your head. For maximum noise attenuation, the clamping pressure of the head- band has been set at the factory. Releasing the clamping pressure by bending the headband is not advised, because loss of attenuation will result. The microphone boom is fully adjustable and will rotate 180 degrees for use on the left or right side of the head. The locking screw that secures the boom to the ear cup is factory set to insure the correct tension. Turning it will not change the tension, because the nut on the inside of the cup will turn as well. Microphone placement should be at the corner of the mouth, approximately ¼” from the lips. The exclusive thumb screw on the mic boom may be used to assure proper placement. When you first connect the headset, turn the volume control on the headset up to the full clockwise position, then adjust the listening volume with the audio control of either your radio or intercom as appropriate. If applicable, crew mem- bers should also turn their individual headset volumes up fully. Doing this allows for a full range of adjustment for each passenger, since those with the most acute hearing can turn their headset volume down, if necessary. continued on back… The headset parts may be cleaned with mild soap and water using a soft cloth. Then dry immediately. Caution: Do Not immerse any part of the headset in water or any other liquid. Be especially careful not to allow the microphone to become wet! Exposure to moisture may cause internal corrosion and failure and will void your manufacturers warranty. Cleaning will help the headset maintain its “like new” condition for many years. WINDSCREEN The microphone windscreen will reduce annoying wind noise and breath pops picked up by headset microphones. It also protects the microphone element from dirt and moisture. The windscreen should be washed regularly to maintain hygiene and avoid clogging. Wash in warm water and mild soap. Rinse thoroughly and make sure it is completely dry before putting it back on. To remove the windscreen, take out the screw that holds the microphone on the boom and grasp the windscreen lightly along its entire length and slip it off. Put the windscreen on the microphone by gently pulling from the open end. Do not pull it so tightly that it stretches against the end of the microphone. WARRANTY Your headset is covered by a limited two-year parts and labor warranty. Please see the enclosed warranty card for details. You may refer to the parts list on the reverse side, if you choose to replace parts yourself. The parts list describes parts for this particular headset only. Parts lists for other models are available on our Web Site or can be obtained by contacting Sigtronics Corporation. Sigtronics Corporation 178 East Arrow Highway San Dimas, CA 91773 Phone: 909 305-9399 E-mail: [email protected] Web Site: www.sigtronics.com S igtronics ® igtronics ® S …when it counts!

S igtronics ® igtronics ® S …when it counts! Sigtronics Corporation 178 East Arrow Highway San Dimas, CA 91773 Phone: 909 305-9399 E-mail: [email protected] Web Site: www.sigtronics.com Model SE-2 Headset Instructions The SE-2 series headset is adjusted at the factory for immediate use with all Sigtronics emergency apparatus intercoms and radio adapters in emergency vehicles. The headset is equipped with a single plug and a coiled cord. The head strap is adjustable so you may custom fit the headset. Place the headset over your head and adjust the strap until minimum pressure is felt on the top of your head. For maximum noise attenuation, the clamping pressure of the head- band has been set at the factory. Releasing the clamping pressure by bending the headband is not advised, because loss of attenuation will result. The microphone boom is fully adjustable and will rotate 180 degrees for use on the left or right side of the head. The locking screw that secures the boom to the ear cup is factory set to insure the correct tension. Turning it will not change the tension, because the nut on the inside of the cup will turn as well. Microphone placement should be at the corner of the mouth, approximately ¼” from the lips. The exclusive thumb screw on the mic boom may be used to assure proper placement. When you first connect the headset, turn the volume control on the headset up to the full clockwise position, then adjust the listening volume with the audio control of either your radio or intercom as appropriate. If applicable, crew mem- bers should also turn their individual headset volumes up fully. Doing this allows for a full range of adjustment for each passenger, since those with the most acute hearing can turn their headset volume down, if necessary. continued on back… The headset parts may be cleaned with mild soap and water using a soft cloth. Then dry immediately. Caution: Do Not immerse any part of the headset in water or any other liquid. Be especially careful not to allow the microphone to become wet! Exposure to moisture may cause internal corrosion and failure and will void your manufacturers warranty. Cleaning will help the headset maintain its “like new” condition for many years. WINDSCREEN The microphone windscreen will reduce annoying wind noise and breath pops picked up by headset microphones. It also protects the microphone element from dirt and moisture. The windscreen should be washed regularly to maintain hygiene and avoid clogging. Wash in warm water and mild soap. Rinse thoroughly and make sure it is completely dry before putting it back on. To remove the windscreen, take out the screw that holds the microphone on the boom and grasp the windscreen lightly along its entire length and slip it off. Put the windscreen on the microphone by gently pulling from the open end. Do not pull it so tightly that it stretches against the end of the microphone. WARRANTY Your headset is covered by a limited two-year parts and labor warranty. Please see the enclosed warranty card for details. You may refer to the parts list on the reverse side, if you choose to replace parts yourself. The parts list describes parts for this particular headset only. Parts lists for other models are available on our Web Site or can be obtained by contacting Sigtronics Corporation.