SimplyShade Concrete Mount Kit Manuals

Concrete In-Ground Wood I n s t r u c t i o n M a n u a l Mount Kits 1 Please remove all contents from the package, inspect and review check list. CAUTION: To reduce personal injury and damage to your mount kit or umbrella, read and follow this instruction manual. Save information for future reference. Concrete Mount Kit check list: A - Adapter Plate (8.5” diameter) B - Screw Anchors 3/8” x 3” (4) A B C B A D In-Ground Fitting Kit check list: A - Adapter Plate (8.5” diameter) B - In-Ground Fitting C - Stem Bolts (4) D - Allen Wrench Wooden Deck Mount Kit check list: A - Adapter Plate B - Base Plate C - Round Countersunk Bolts (4)-- D - Allen Wrench B A MOUNT KIT CHECK LIST C D At least 6” thick Rotating Hub AMK Adapter Plate Hub Bolts & Washers Screw Anchors 2 Concrete Mount Kit includes: A - Adapter Plate (8.5” diameter) B - Screw Anchors 3/8” x 3” (4) CONCRETE MOUNT KIT S T E P 1 Bolt Adapter Plate Bolt the adapter plate (countersunk holes faced down) to an existing concrete slab (or through no thicker than 1” pavers or tiles adhered to a concrete slab) using the supplied screw anchors. Use a 5/16” drill bit for holes. S T E P 2 Attach Rotating Hub to Adapter Plate Attach rotating hub to adapter plate using the hub bolts that came with your umbrella. S T E P 3 Attach Umbrella Slide frame over the newly mounted rotating hub. See your umbrella instruction manual for further assistance. You are now ready to operate your umbrella! REMOVAL: To remove your umbrella for seasonal storage or to move it to another base plate or in-ground fitting, see your umbrella Instruction Manual for further assistance on how to remove umbrella. A B 3 IN-GROUND MOUNT KIT S T E P 1 Preparation The in-ground fitting should or can be built into newly poured concrete. For a perfect flush mount, set the plate of the fitting 3/8” below the final surface grade. When you add the 3/8” thick adapter plate to the fitting plate, the adapter plate will be flush with the concrete. S T E P 2 Bolt Adapter Plate Once installed and the concrete has cured, bolt the adapter plate (countersunk holes face up) to the top of the in-ground fitting using the four (4) stem bolts and allen wrench. Insert the stem bolts downward through the countersunk holes in the adapter plate and screw them into the threaded holes in the top of the in-ground fitting. Make sure they are very tight. S T E P 3 Attach Rotating Hub Attach rotating hub to adapter plate using the hub bolts that came with your umbrella. S T E P 4 Attach Umbrella Slide frame over the newly mounted rotating hub. See your umbrella instruction manual for further assistance. You are now ready to operate your umbrella! IMPORTANT: When concreting the in-ground fitting in place, make sure not to get slurry in the screw threads. Either apply tape over the holes on both sides of the fitting or place the stem bolts in the threads and withdraw them when the concrete is set. Make sure that the in-ground fitting is perfectly level. Allow the concrete to cure for the appropriate cure time for your area before installing the umbrella onto the fitting. REMOVAL: To remove your umbrella for seasonal storage or to move it to another base plate or in-ground fitting, see your umbrella Instruction Manual for further assistance on how to remove umbrella. C B Ground Level Concrete Footing Flare at bottom 1.0m or 3’4” In-Ground Fitting AMK Adapter Plate Ground Stem Bolts Rotating Hub Hub Bolts & Washers Hole Diameter 500mm or 21” - 24” A D In-Ground Fitting Kit includes: A - Adapter Plate (8.5” diameter) C - Stem Bolts (4) B - In-Ground Fitting D - Allen Wrench