SimplyShade UA38278RLD-LS Manuals

ITEM #0804782 MODEL #UA38278RLD-LS 9 FT UMBRELLA WITH LED LIGHTS 1 ATTACH YOUR RECEIPT HERE Serial Number Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-844-230-9904,8 a.m. – 8 p.m., EST, Monday - Friday. SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. Assemble on a soft, clean, non-abrasive surface to avoid scratching the metal finish or hurting the umbrella fabric. Always keep the umbrella in the closed position when not in use. Do not open the umbrella in high winds or windy conditions. Use a heavy or weighted umbrella base to stabilize the umbrella. This outdoor umbrella is designed and made for personal non-commercial use. It should not be used as a toy or a tool. Children under age of 16 should not be engaged in the assembly, removal or disassembly. Children under age of 10 should be supervised by a competent adult while using this umbrella. PREPARATION Before beginning to assemble the product, remove all parts from carton and make sure everything is present. Compare parts with package contents list. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Estimated Assembly Time: 10 minutes NO TOOLS REQUIRED PACKAGE CONTENTS D A C E B x1 AC Adapter Bottom Pole x1 Finial x1 Umbrella x1 Solar Panel NOTE: The Finial (D) contains two lithium batteries (2 x 2200mAh) . Do not attempt to open the Finial (D) when in use. Do not use the Umbrella (A) without the Finial (D) properly installed. AC Adapter Input: 100V~240V AC, Output: 4.2V DC x1 2 CARE AND MAINTENANCE Wash with mild soap and water; rinse with clean water and let air dry. Always let the umbrella dry completely before storing. Store the umbrella out of extreme weather or high winds. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reposition or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. CAUTION To prevent personal injury or damage, always take down the umbrella when not in use, during windy conditions or in rain. Do not operate or attempt to charge the umbrella when water is present so as to prevent damage to the electrical components. FEELING CONFIDENT? START YOUR NEXT PROJECT Visit www.lowes.com for more information. INSTALLATION OVERVIEW 1. 1 2 A C Carefully remove the umbrella and all contents from the box. Locate the Finial (D) and the Solar Panel (C). Separate the Plastic Cap (F) from the Finial (D) by twisting the Cap (F) counter-clockwise approximately 1/4 turn and pulling apart. With the Cap (F) removed from the top of the Finial (D), line the tabs on the bottom of the Solar Panel (C) up with the slots inside the top of the Finial (D). Insert the bottom of the Solar Panel (C) into the top of the Finial (D) and twist clockwise approximately 1/4 turn until it is secure. NOTE: To increase the lifespan of the Solar Panel (C) it is recommended it be removed and stored away when not in use for extended periods of time. Always install the Plastic Cap (F) onto the Finial (D) for protection when the solar panel is removed. With the Solar Panel (C) installed securely onto the top of the Finial (D), insert the threads on the bottom of the Finial (D) into the top of the Umbrella (A). Turn the Finial (D) clockwise to tighten the threads until the Finial (D) is secure on the Umbrella (A). Check to ensure that the Solar Panel (C) did not come loose in this process and is still securely on top of the Finial (D). D F C D D 3 3 A B 4 Push Button Tilt To open the Umbrella (A), turn the crank handle on the Umbrella (A) in a clockwise direction until the canopy opens all the way. With the canopy fully opened, simply push the button and manually tilt the canopy. To close the Umbrella (A), tilt the canopy back into a straight and up-right position. Turn the crank handle in a counter-clockwise direction . Insert and secure the Bottom Pole (B) into an umbrella base (sold separately). Insert Umbrella (A) into the Bottom Pole (B) ensuring that the push-pin on the Umbrella (A) pole snaps securely into the Bottom Pole (B). push- pin B 4 INSTALLATION OVERVIEW OPERATION OVERVIEW open