Smartek NUBI 4.0 Manuals

NB40F2 REV 01 – Nov. 2018 - ENGLISH NUBI 4.0 Model: NB40F2 Power supply: 12VDC PIR: yes Thank you for purchasing NUBI 4.0, the intelligent smoke screen security device able to be connected to any burglar alarm system in new or existing systems. OPERATIONAL OVERVIEW The device is powered from 10VDC to 15VDC, usually supplied by the alarm control panel, the consumption is less than 1mW. NUBI 4.0 does not require any additional energy from the external power supply when the smoke cartridge is ignited, as this energy has already been stored on the motherboard. This ensures the ignition of the cartridge in any power condition and the guarantee of not having any overload on the power supply even in case of simultaneous triggering of many NUBI 4.0 devices. NUBI 4.0 efficiently protects volumes up to 100 m3. The smoke generated by NUBI 4.0 is based on incense and does not produce toxic atmosphere as tested according to the TLV-STEL directive EU 2017/164 and ACGIH. After use the room must be ventilated before staying there. NUBI 4.0 is activated through 3 inputs: one input drives the immediate emission of smoke, while the other two inputs realize a triple-consent logic to avoid false alarms. In this case, to trigger the emission of smoke, it is necessary that the state of the burglar system is armed, then within a time window of 15 minutes two other conditions occur: 1) The burglar system goes into alarm 2) The integrated NUBI 4.0 PIR sensor detects movement At the moment the second condition has been reach, the smoke will be emitted immediately. The inputs polarity and logic level can be easily configured using the DIP switches in order to interface NUBI 4.0 with any burglar panel. NUBI 4.0 has got two outputs to inform other devices about alarm state and the detection of the movement by the PIR. The output logic level can be reversed using DIP switches. The box opening is detected with a tamper switch, its clean contact can be connected to the burglar panel. An optional internal siren can be housed inside the box and plugged to the proper motherboard connector. The smoke cartridge works only once, the smoke emission, when triggered, can no longer be interrupted. The smoke cartridge replacement is very easy, each spare cartridge is provided with a special board soldered on its wires to be easily plugged on the proper motherboard connector. INSTALLATION NUBI 4.0 can be easily installed on the wall or even in a corner at a height between 150 and 250 cm. WARNING Do not insert any obstacle at a distance of less than 1.5 meters from the smoke outlet hole. The best performance is achieved when the jet of smoke coming out from NUBI 4.0 directly hits the floor, in this way the smoke will cool and spread better. After opening the top cover, remove the motherboard to fix the lower part of the box on the wall. 1 Motherboard rails 2 Cabling wire buttonhole 3 Internal siren fixing spacers 4 Internal siren sound outlet hole 5 Device fixing holes 6 Smoke cartridge supports

NB40S1 REV 01 – Nov. 2018 - ENGLISH NUBI 4.0 Model: NB40S1 Power supply: 12VDC PIR: NO Thank you for purchasing NUBI 4.0, the intelligent smoke screen security device able to be connected to any burglar alarm system in new or existing systems. OPERATIONAL OVERVIEW The device is powered from 10VDC to 15VDC, usually supplied by the alarm control panel, the consumption is less than 1mW. NUBI 4.0 does not require any additional energy from the external power supply when the smoke cartridge is ignited, as this energy has already been stored on the motherboard. This ensures the ignition of the cartridge in any power condition and the guarantee of not having any overload on the power supply even in case of simultaneous triggering of many NUBI 4.0 devices. NUBI 4.0 efficiently protects volumes up to 100 m3. The smoke generated by NUBI 4.0 is based on incense and does not produce toxic atmosphere as tested according to the TLV-STEL directive EU 2017/164 and ACGIH. After use the room must be ventilated before staying there. This version of NUBI 4.0 has no integrated PIR, it has only the input to trigger the immediate smoke delivery. The polarity of this input and its logic can be easily configured using DIP switches to interface NUBI 4.0 with anyburglar panel or command device. The box opening is detected with a tamper switch, its clean contact can be connected to the burglar panel. The smoke cartridge works only once, the smoke emission, when triggered, can no longer be interrupted. The smoke cartridge replacement is very easy, each spare cartridge is provided with a special board soldered on its wires to be easily plugged on the proper motherboard connector. INSTALLATION NUBI 4.0 can be easily installed on the wall or even in a corner at a height between 150 and 250 cm. WARNING Do not insert any obstacle at a distance of less than 1.5 meters from the smoke outlet hole. The best performance is achieved when the jet of smoke coming out from NUBI 4.0 directly hits the floor, in this way the smoke will cool and spread better. After opening the top cover, remove the motherboard to fix the lower part of the box on the wall. 1 Motherboard rails 2 Cabling wire buttonhole 3 Internal siren fixing spacers 4 Internal siren sound outlet hole 5 Device fixing holes 6 Smoke cartridge supports

NB40PP2UX REV 01 – March 2020 - ENGLISH NUBI 4.0 – PLUG & PLAY Thank you for purchasing NUBI 4.0, the wireless, intelligent and Plug & Play security smoke screen device. It can be used with any anti-theft system, coupling the device to an internal siren. WE RECOMMEND THAT YOU READ THE ENTIRE MANUAL BEFORE PROCEEDING TO PRODUCT INSTALLATION. 1. OVERVIEW The device is self-powered with a 3.6 V AA size lithium battery supplied with the product; in a not excessively noisy environment it lasts up to 10 years. When the battery is running low, the device will beep every 8 hours. NUBI 4.0 drives a XAFER S25 smoke canister, which effectively protects volumes up to 100 m3. The smoke generated is suitable for indoor use, it is based on incense and does not produce a toxic atmosphere as tested according to the directive TLV-STEL EU 2017/164 and ACGIH. After use, the room must be adequately ventilated before staying there. NUBI 4.0 Plug&Play works completely wireless, does not need any connections with the existing anti-theft system but it is alert when it hears the sound of the internal siren of the system. The coupling operation with the siren, to be performed during installation, learns the sound in digital form. Sounds different from that of the specific coupled siren will not produce any effect, even the sound of the siren itself, but installed in a position other than the coupling one, will not activate NUBI 4.0. NUBI 4.0 is normally in "sleep mode" with the smoke supply inhibited. When NUBI 4.0 decodes a sound corresponding to that of the coupled siren, it switches to "active state" and as soon as it detects movement with its infrared sensor, it triggers the emission of smoke. It is possible to extend for 5 or 10 minutes the duration of the "active state" of NUBI 4.0 even after the siren has stopped sounding (see chapter 5. CONFIGURATION). For the first 20 minutes after the siren coupling operation, or after inserting the power supply battery, smoke emission is inhibited to allow functional control of the device. The smoke canister is disposable, the smoke emission, when activated, can no longer be interrupted. NUBI 4.0 is a family of products, in addition to the Plug&Play version, other models are available to be connected to the alarm control unit via inputs and outputs. They are available with 12V or battery power supply, with or without built-in infrared sensor. For more information, visit the website www.smarteksrl.it. 2. POSITIONING NUBI 4.0 can be easily installed on the wall or even in a corner at a height between 150 and 250 cm. WARNING Do not insert any obstacle at a distance of less than 1.5 meters from the smoke outlet hole. The best performance is achieved when the jet of smoke coming out from NUBI 4.0 directly hits the floor, in this way the smoke will cool and spread better. NUBI 4.0 Plug & Play must be installed in the same room where an internal siren of the alarm system is located. Do not pair NUBI 4.0 with sirens located in other rooms that are separated with doors that can sometimes be open and sometimes closed. Do not place NUBI 4.0 in particularly noisy places, as well as near strong sound sources, such as television or speakers. Strong and continuous sound sources will reduce battery life. NUBI 4.0 works when it is reached by a siren sound level ranging from 85 to 103 DB. Indicatively, the distance between NUBI 4.0 and the siren should be between 0.5 and 3m, but this parameter strongly depends on each siren. Being able to choose, it is always preferable to keep the siren as close as possible to NUBI 4.0. To obtain maximum immunity to anomalies due to ambient sound reflections, it is recommended to install the siren and NUBI 4.0 at a height greater than 2 meters. Before drilling the wall to permanently fix NUBI 4.0, we recommend carrying out the sound test described in the chapter 14. SOUND CHECK. 3. CONTENT The package contains N. 1 NUBI 4.0 Plug & Play device in plastic container resistant to high temperatures, complete with electronic board and infrared sensor. N. 1 3.6V lithium battery in stylus format N. 1 permanent magnet for programming. The smoke canister XAFER S25 is not included, but must be purchased separately.