Smartenit IoTeMtr 3017 Manuals

© 2020 Compacta International, Ltd.—Rev 0.1 05/28/2020 IoTeMtr and Smartenit are trademarks of Compacta International, Ltd Zigbee is a registered trademark of the zigbee alliance Quick Start Guide Technical Support [email protected] Wireless Six-Channel Energy Meter IoTeMtr Models #3017, 3017W and 3017L About this Product Use the IoTeMtr to measure the characteristics of two 3-phase cir- cuits or six single or split phase circuits, including voltage, frequency, current, power and active/reactive energy imported or exported. The device interfaces wirelessly within IoT/Home Automation net- works where it can be controlled and monitored by automation hubs or cloud services. In order to measure energy, the device requires voltage and current inputs plus the supply voltage to power the unit itself. This guide shows how to connect the input voltage and current measurement transformers (CTs). Install with the tips and suggestions below to get the benefits of the Internet of Things through your automation controller. Electrical Installation For indoor installation only as supplied. When installing outdoors, it is imperative to use a suitable enclo- sure, and to observe all water-tight precautions to ensure the life and safety of the device. When wiring the AC voltage input connector, use a suitable breaker and beware of the dangerous voltages present. Installation recommended to be done by trained personnel only. Follow the diagrams below to connect the device to the electrical panel based on the type of circuits to be moni- tored. The 3 CTs for each circuit MUST be the same cur- rent rating (e.g. 30A, 50A, 100A) © 2020 Compacta International, Ltd.—Rev 0.1 05/28/2020 IoTeMtr and Smartenit are trademarks of Compacta International, Ltd Zigbee is a registered trademark of the zigbee alliance Quick Start Guide Technical Support [email protected] © 2020 Compacta International, Ltd.—Rev 0.1 05/28/2020 IoTeMtr and Smartenit are trademarks of Compacta International, Ltd Zigbee is a registered trademark of the zigbee alliance Quick Start Guide Technical Support [email protected] Setup 1) Setup Operation Mode 1. Tap pushbutton two times then hold it for 3 seconds. LED will go off indicating device is now in Mode configuration 2. Now tap the number of times to select the desired mode using the table on the right. The LED will then blink the number of times tapped to confirm the selection. 2) Setup CT connected to each channel 1. Tap four times then hold pushbutton for 3 seconds. LED will turn off indicating device is in CT configuration 2. Use the table on the right to select the channel(s) to be config- ured. The LED will then blink the number of times tapped to confirm the selection 3. Use the table below to select the type of CT connected to the selected channel. LED will then blink the number of tapped times to confirm selection. SET Pushbutton Functionality Operation Pushbutton Device Behavior Leave Network Tap 13 times Status LED will begin fast blinking Close Permit Join Press and hold for 3 seconds when de- vice is in open per- mit join Status LED will stop flashing Soft Reset (Reboot Device) Tap 10 times Request Firmware Update (OTA) Tap 6 times Restore Factory Set- tings Tap 9 times Setup Operation Mode and CT gain See below See below Status LED Indications Pattern Indication Fast Flashing Searching for network Solid Joined to network Flash once per second Open permit join Short blip, pause-0.5 secs Binding to Endpoint 1 (On/Off) 2 blips per second Disconnected from net- work Taps Mode 1 Single-Phase—6 Channels (default) 2 Split Phase—6 Channels 3 3 Phase—2 Channels Taps Channel Selected 1-6 Select channel 1-6* 7 Select all channels * If device is in 3-Phase mode, select cha- nel 1 or 2, or 7 for both channels Taps CT Selected Taps CT Selected Taps CT Selected 1 10A 4 40A 7 100A 2 20A 5 50A 8 200A 3 30A (Default) 6 60A 9 400A © 2020 Compacta International, Ltd.—Rev 0.1 05/28/2020 IoTeMtr and Smartenit are trademarks of Compacta International, Ltd Zigbee is a registered trademark of the zigbee alliance Quick Start Guide Technical Support [email protected] Setup (Cont.) 1) Factory Reset (Restore Factory Settings) While powering the device, press the SET button and release it once the device powers up. Alternatively, if the device is already joined to a Zigbee network, quickly tap the SET button 13 times. The Status LED will go out for 1 second and then begin flashing rapidly. The IoTeMtr will then search for an open Zigbee network to join. 2) Joining device to a Zigbee network 1. Set network controller to discover devices (Open Permit Join) 2. As the IoTeMtr joins, the Status LED blinking rate will slow until it stays solid, indicating it has fully joined the Zigbee network. 3) Binding to be controlled by other devices To allow On/Off control by another device, tap the SET button once quickly and within 1/2 second press and hold it for 3 seconds. The Status LED will blink per the pattern described in the Status LED Indications table above. 4) Allowing other devices to join Zigbee network (Open Permit Join) As a Zigbee “Router”, the IoTeMtr can also be put in discovery mode to permit other devices to join the Zigbee network. Do note that ultimately the network manager device will decide whether to allow the new device to fully join. Assuming the IoTeMtr is already in a Zigbee network, it can open the network for other devices to join as follows: 1. Press and hold the SET button for 6 seconds. The STATUS LED will blink once per second and the net- work will be open for joining for up to 4 minutes 2. Permit-join can be stopped by pressing and holding the SET button for 3 seconds. The LED will stop blinking.