Sony CDX-M770 - Fm/am Compact Disc Player Manuals

® LIMITED WARRANTY (U.S. Only) Sony Electronics Inc. (“Sony”) warrants this product against defects in material or workmanship for the time periods and as set forth below. Pursuant to this Limited Warranty, Sony will, at its option, (i) repair the product using new or refurbished parts or (ii) replace the product with a new or refurbished product. For purposes of this Limited Warranty, “refurbished” means a product or part that has been returned to its original specifications. In the event of a defect, these are your exclusive remedies. Labor: For a period of one (1) year from the original date of purchase of the product (“Labor Warranty”), Sony will, at its option, repair or replace with new or refurbished product, product determined to be defective. If Sony elects to replace the product after this Labor Warranty has expired but while the Parts Warranty below is still in effect, it will do so for the applicable labor charge. Parts: For a period of one (1) year from the original date of purchase of product (“Parts Warranty”), Sony will supply new or refurbished replacement parts in exchange for parts determined to be defective. This Limited Warranty covers only the hardware components packaged with the Product. It does not cover technical assistance for hardware or software usage and it does not cover any software products whether or not contained in the Product; any such software is provided “AS IS” unless expressly provided for in any enclosed software Limited Warranty. Please refer to the End User License Agreements included with the Product for your rights and obligations with respect to the software. Instructions: To obtain warranty service, you must deliver the product, freight prepaid, in either its original packaging or packaging affording an equal degree of protection to the Sony authorized service facility specified. It is your responsibility to backup any data, software or other materials you may have stored or pre- served on your unit. It is likely that such data, software, or other materials will be lost or reformatted during service and Sony will not be responsible for any such damage or loss. A dated purchase receipt is required. For specific instructions on how to obtain warranty service for your product, Visit Sony’s Web Site: www.sony.com/service Or call the Sony Customer Information Service Center 1-800-222-SONY(7669) For an accessory or part not available from your authorized dealer, call: 1-800-488-SONY (7669) Repair / Replacement Warranty: This Limited Warranty shall apply to any repair, replacement part or replace- ment product for the remainder of the original Limited Warranty period or for ninety (90) days, whichever is longer. Any parts or product replaced under this Limited Warranty will become the property of Sony. This Limited Warranty only covers product issues caused by defects in material or workmanship during ordinary consumer use; it does not cover product issues caused by any other reason, including but not limited to product issues due to commercial use, acts of God, misuse, limitations of technology, or modification of or to any part of the Sony product. This Limited Warranty does not cover Sony products sold AS IS or WITH ALL FAULTS or consumables (such as fuses or batteries). This Limited Warranty is invalid if the factory-applied serial number has been altered or removed from the product. This Limited Warranty is valid only in the United States. LIMITATION ON DAMAGES: SONY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. DURATION OF IMPLIED WARRANTIES: EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This Limited Warranty gives you specific legal rights and you may have other rights which vary from state to state. Car Audio 3-272-643-01 Printed in Japan

Operating Instructions Manual de instrucciones Bruksanvisning Manual de instruções Oδηγίες Λειτυργίας Инструкция по эксплуатации For installation and connections, see the supplied installation/connections manual. Para obtener información sobre la instalación y las conexiones, consulte el manual de instalación/conexiones suministrado. Vi hänvisar till det medföljande häftet angående montering/anslutningar. Para a instalação e as ligações, consulte o manual de instalação/ligações fornecido. Για την εγκατάσταση και τις συνδέσεις, δείτε τ συνδευτικ εγειρίδι Εγκατάσταση/Συνδέσεις. Перед установкой и подсоединениями прочитайте прилагаемую инструкцию по установке и подсоединению. © 2001 Sony Corporation GB ES SE PT GR RU 3-230-448-21 (1) FM/MW/LW Compact-/Mini- Disc Player FM/MW/LW Compact Disc Player CDX-M770 CDX-M670 FM/MW/LW Mini Disc Player MDX-M690

Operating Instructions Mode d’emploi Manual de instrucciones Owner’s Record The model and serial numbers are located on the bottom of the unit. Record these numbers in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. CDX-M770/M670/M620 Serial No. CDX-M770 CDX-M670 CDX-M620 For installation and connections, see the supplied installation/connections manual. En ce qui concerne l’installation et les connexions, consulter le manuel d’installation/raccordement fourni. Para obtener información sobre la instalación y las conexiones, consulte el manual de instalación/conexiones suministrado. © 2001 Sony Corporation 3-230-446-11 (1) US FR ES FM/AM Compact Disc Player

L R AUDIO OUT FRONT AUDIO OUT REAR BUS AUDIO 1 3 5 7 2 4 6 8 5 7 4 6 8 Sony Corporation © 2001 Printed in Korea 3-230-449-11 (1) 1 3 4 2 6 8 Equipment used in illustrations (not supplied) In Abbildungen dargestellte Geräte (nicht mitgeliefert) Appareils utilisés dans les illustrations (non fournis) Apparecchiatura utilizzata nelle illustrazioni (non in dotazione) Apparatuur gebruikt voor illustratiedoeleinden (niet meegeleverd) Rear speaker Hecklautsprecher Haut-parleur arrière Diffusori posteriori Achterluidspreker Front speaker Frontlautsprecher Haut-parleur avant Diffusori anteriori Voorluidspreker 1 CD/MD changer CD/MD-Wechsler Changeur de CD/MD Cambia CD/MD CD/MD-wisselaar Rotary commander RM-X4S Joystick RM-X4S Satellite de commande RM-X4S Telecomando a rotazione RM-X4S Bedieningssatelliet RM-X4S Power amplifier Endverstärker Amplificateur de puissance Amplificatore di potenza Eindversterker × 2 5 7 2 A B 3 Cautions •This unit is designed for negative earth 12 V DC operation only. •Do not get the wires under a screw, or caught in moving parts (e.g. seat railing). •Before making connections, turn the car ignition off to avoid short circuits. •Connect the power connecting cord 8 to the unit and speakers before connecting it to the auxiliary power connector. •Run all earth wires to a common earth point. •Be sure to insulate any loose unconnected wires with electrical tape for safety. Notes on the power supply cord (yellow) •When connecting this unit in combination with other stereo components, the connected car circuit’s rating must be higher than the sum of each component’s fuse. •When no car circuits are rated high enough, connect the unit directly to the battery. Parts list (1) The numbers in the list are keyed to those in the instructions. For the use of release key qs, see the supplied operating instructions. Caution Handle the bracket 1 carefully to avoid injuring your fingers. Connection example (2) Notes (2-A) • Be sure to connect the earth cord before connecting the amplifier. • If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be deactivated. Tip (2-B- ) For connecting two or more CD/MD changers, the source selector XA-C30 (optional) is necessary. Connection diagram (3) A To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit. B To the interface cable of a car telephone Warning If you have a power aerial without a relay box, connecting this unit with the supplied power connecting cord 8 may damage the aerial. Notes on the control leads • The power aerial control lead (blue) supplies +12 V DC when you turn on the tuner or when you activate the AF (Alternative Frequency), TA (Traffic Announcement) function. • When your car has built-in FM/MW/LW aerial in the rear/side glass, connect the power aerial control lead (blue) or the accessory power input lead (red) to the power terminal of the existing aerial booster. For details, consult your dealer. • A power aerial without a relay box cannot be used with this unit. Memory hold connection When the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. Notes on speaker connection • Before connecting the speakers, turn the unit off. • Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. • Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker. • Do not connect the earth lead of this unit to the negative (–) terminal of the speaker. • Do not attempt to connect the speakers in parallel. • Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. • To avoid a malfunction, do not use the built-in speaker wires installed in your car if the unit shares a common negative (–) lead for the right and left speakers. • Do not connect the unit’s speaker cords to each other. Précautions •Cet appareil est conçu pour fonctionner sur courant continu de 12 V avec masse négative. •Evitez de fixer des vis sur les câbles ou de coincer ceux-ci dans des pièces mobiles (par exemple, armature de siège). •Avant d’effectuer des raccordements, éteignez le moteur pour éviter les courts-circuits. •Branchez le cordon d’alimention 8 sur l’appareil et les haut-parleurs avant de le brancher sur le connecteur d’alimentation auxiliaire. •Rassemblez tous les fils de terre en un point de masse commun. •Veillez à isoler avec du chatterton tout fil lâche non raccordé. Remarques sur le cordon d’alimentation (jaune) •Lorsque cet appareil est raccordé à d’autres éléments stéréo, la valeur nominale des circuits de la voiture raccordée doit être supérieure à la somme des fusibles de chaque élément. •Si aucun circuit de la voiture n’est assez puissant, raccordez directement l’appareil à la batterie. Liste des composants (1) Les numéros de l’illustration correspondent à ceux des instructions. Pour l’utilisation de la clé de déblocage qs, reportez-vous au mode d’emploi. Attention Manipulez précautionneusement le support 1 pour éviter de vous blesser aux doigts. Exemple de raccordement (2) Remarques (2-A) • Raccordez d’abord le fil de masse avant de raccorder l’amplificateur. • Si vous raccordez un amplificateur de puissance indépendant et que vous n’utilisez pas l’amplificateur intégré, le bip sonore est désactivé. Conseil (2-B- ) Dans le cas du raccordement de deux changeurs de CD/MD ou plus, le sélecteur de source XA-C30 (en option) est indispensable. Schéma de raccordement (3) A Au niveau du AMP REMOTE IN d’un amplificateur de puissance facultatif Ce raccordement existe seulement pour les amplificateurs. Le raccordement à tout autre système peut endommager l’appareil. B Vers le cordon de liaison d’un téléphone de voiture Avertissement Si vous disposez d’une antenne électrique sans boîtier de relais, le branchement de cet appareil au moyen du cordon d’alimentation fourni 8 risque d’endommager l’antenne. Remarques sur les fils de contrôle • Le fil de commande (bleu) de l’antenne électrique assure une alimentation de +12 V CC lorsque vous mettez le syntoniseur sous tension ou lorsque vous activez la fonction AF (fréquence secondaire) ou TA (informations routières). • Lorsque votre voiture est équipée d’une antenne FM/MW/LW intégrée dans la vitre arrière/latérale, raccordez la sortie de commande de l’antenne (bleu) ou l’entrée d’alimentation des accessoires (rouge) au bornier de l’amplificateur d’antenne existant. Pour plus de détails, consultez votre revendeur. • Une antenne électrique sans boitier de relais ne peut pas être utilisée avec cet appareil. Raccordement pour la conservation de la mémoire Lorsque le fil d’entrée d’alimentation jaune est raccordé, le circuit de la mémoire est alimenté en permanence même si la clé de contact est sur la position d’arrêt. Remarques sur le raccordement des haut-parleurs • Avant de raccorder les haut-parleurs, mettez l’appareil hors tension. • Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms avec une capacité de manipulation adéquate pour éviter de les endommager. • Ne raccordez pas les bornes du système de haut- parleurs au châssis de la voiture et ne raccordez pas les bornes du haut-parleur droit à celles du haut-parleur gauche. • Ne raccordez pas le câble de masse de cet appareil à la borne négative (–) de l’enceinte. • N’essayez pas de raccorder les haut-parleurs en parallèle. • Raccordez uniquement des haut-parleurs passifs. Le raccordement de haut-parleurs actifs (avec amplificateurs intégrés) aux bornes des haut- parleurs peut endommager l’appareil. • Pour éviter tout dysfonctionnement, n’utilisez pas les fils des haut-parleurs intégrés installés dans votre voiture si l’appareil partage un fil négatif commun (–) pour les haut-parleurs droit et gauche. • Ne raccordez pas entre eux les cordons des haut- parleurs de l’appareil. Vorsicht • Dieses Gerät ist ausschließlich für den Betrieb bei 12 V Gleichstrom (negative Erdung) bestimmt. • Achten Sie darauf, daß die Kabel nicht unter einer Schraube oder zwischen beweglichen Teilen wie z. B. in einer Sitzschiene eingeklemmt werden. • Schalten Sie, bevor Sie irgendwelche Anschlüsse vornehmen, die Zündung des Fahrzeugs aus, um Kurzschlüsse zu vermeiden. • Verbinden Sie das Stromversorgungskabel 8 mit dem Gerät und den Lautsprechern, bevor Sie es mit dem Hilfsstromanschluß verbinden. • Schließen Sie alle Erdungskabel an einen gemeinsamen Massepunkt an. • Aus Sicherheitsgründen müssen alle losen, nicht angeschlossenen Drähte mit Isolierband abisoliert werden. Hinweise zum Stromversorgungskabel (gelb) • Wenn Sie dieses Gerät zusammen mit anderen Stereokomponenten anschließen, muß der Autostromkreis, an den die Geräte angeschlossen sind, eine höhere Leistung aufweisen als die Summe der Sicherungen der einzelnen Komponenten. • Wenn kein Autostromkreis eine so hohe Leistung aufweist, schließen Sie das Gerät direkt an die Batterie an. Teileliste (1) Die Nummern in der Liste sind dieselben wie im Erläuterungstext. Wie Sie den Löseschlüssel qs verwenden, schlagen Sie bitte in der mitgelieferten Bedienungsanleitung nach. Vorsicht Seien Sie beim Umgang mit der Halterung 1 vorsichtig, damit Sie sich nicht die Hände verletzen. Anschlußbeispiel (2) Hinweise (2-A) • Schließen Sie unbedingt zuerst das Massekabel an, bevor Sie den Verstärker anschließen. • Wenn Sie einen gesondert erhältlichen Endverstärker anschließen und den integrierten Verstärker nicht benutzen, wird der Signalton deaktiviert. Tip (2-B- ) Zum Anschließen von zwei oder mehr CD/MD- Wechslern wird der gesondert erhältliche Signalquellenwähler XA-C30 benötigt. Anschlußdiagramm (3) A An AMP REMOTE IN des gesondert erhältlichen Endverstärkers Dieser Anschluß ist ausschließlich für Verstärker gedacht. Schließen Sie nichts anderes daran an. Andernfalls kann das Gerät beschädigt werden. B An Schnittstellenkabel eines Autotelefons Warnung Wenn Sie eine Motorantenne ohne Relaiskästchen verwenden, kann durch Anschließen dieses Geräts mit dem mitgelieferten Stromversorgungskabel 8 die Antenne beschädigt werden. Hinweise zu den Steuerleitungen • Die Motorantennen-Steuerleitung (blau) liefert + 12 V Gleichstrom, wenn Sie den Tuner einschalten oder die AF- (Alternativfrequenzsuche) oder die TA- Funktion (Verkehrsdurchsagen) aktivieren. • Wenn das Fahrzeug mit einer in der Heck-/ Seitenfensterscheibe integrierten FM (UKW)/MW/ LW-Antenne ausgestattet ist, schließen Sie die Motorantennen-Steuerleitung (blau) oder die Zubehörstromversorgungsleitung (rot) an den Stromversorgungsanschluß des vorhandenen Antennenverstärkers an. Näheres dazu erfahren Sie bei Ihrem Händler. • Es kann nur eine Motorantenne mit Relaiskästchen angeschlossen werden. Stromversorgung des Speichers Wenn das gelbe Stromversorgungskabel angeschlossen ist, wird der Speicher stets (auch bei ausgeschalteter Zündung) mit Strom versorgt. Hinweise zum Lautsprecheranschluß • Schalten Sie das Gerät aus, bevor Sie die Lautsprecher anschließen. • Verwenden Sie Lautsprecher mit einer Impedanz zwischen 4 und 8 Ohm und ausreichender Belastbarkeit. Ansonsten können die Lautsprecher beschädigt werden. • Verbinden Sie die Lautsprecheranschlüsse nicht mit dem Wagenchassis, und verbinden Sie auch nicht die Anschlüsse des rechten mit denen des linken Lautsprechers. • Verbinden Sie die Masseleitung dieses Geräts nicht mit dem negativen (–) Lautsprecheranschluß. • Versuchen Sie nicht, Lautsprecher parallel anzuschließen. • An die Lautsprecheranschlüsse dieses Geräts dürfen nur Passivlautsprecher angeschlossen werden. Schließen Sie keine Aktivlautsprecher (Lautsprecher mit eingebauten Verstärkern) an, da diese sonst beschädigt werden können. • Um Fehlfunktionen zu vermeiden, verwenden Sie nicht die im Fahrzeug installierten, integrierten Lautsprecherleitungen, wenn am Ende eine gemeinsame negative (–) Leitung für den rechten und den linken Lautsprecher verwendet wird. • Verbinden Sie nicht die Lautsprecherkabel des Geräts miteinander. Let op! • Dit apparaat is ontworpen voor gebruik op gelijkstroom van een 12 Volts auto-accu, negatief geaard. • Zorg ervoor dat de draden niet onder een schroef of tussen bewegende onderdelen (b.v. zetelrail) terechtkomen. • Alvorens aansluitingen te verrichten moet u het contact afzetten om kortsluiting te vermijden. • Sluit het netsnoer 8 aan op het toestel en de luidsprekers vooraleer u het op de hulpvoedingsaansluiting aansluit. • Sluit alle aarddraden op een gemeenschappelijk aardpunt aan. • Voorzie niet aangesloten draden om veiligheidsredenen altijd van isolatietape. Opmerkingen bij de voedingskabel (geel) • Wanneer u dit toestel aansluit samen met andere componenten, moet het vermogen van de aangesloten autostroomkring groter zijn dan de som van de zekeringen van elke component afzonderlijk. • Wanneer het vermogen ontoereikend is, moet u het toestel rechtstreeks aansluiten op de batterij. Onderdelenlijst (1) De nummers in de afbeelding verwijzen naar die in de montage-aanwijzingen. Raadpleeg de meegeleverde gebruiksaanwijzing om de speciale sleutel te bedienen qs. Voorzichtig Houd de beugel 1 voorzichtig vast zodat u uw vingers niet verwondt. Voorbeeldaansluitingen (2) Opmerkingen (2-A) • Sluit eerst de massakabel aan alvorens de versterker aan te sluiten. • Als u een los verkrijgbare vermogensversterker aansluit en de ingebouwde versterker niet gebruikt, is de pieptoon uitgeschakeld. Tip (2-B- ) Om twee of meer CD/MD-wisselaars aan te sluiten, hebt u de geluidsbronkiezer XA-C30 (optioneel) nodig. Aansluitschema (3) A Naar AMP REMOTE IN van een los verkrijgbare vermogensversterker Deze aansluiting is alleen bedoeld voor versterkers. Door een ander systeem aan te sluiten kan het toestel worden beschadigd. B Naar het interface-snoer van een autotelefoon Opgelet Indien u een elektrische antenne heeft zonder relaiskast, kan het aansluiten van deze eenheid met het bijgeleverde netsnoer 8 de antenne beschadigen. Opmerking betreffende de aansluitsnoeren • De voedingskabel (blauw) van de elektrisch bediende antenne levert +12V gelijkstroom wanneer u de tuner aanschakelt of de functie AF (Alternative Frequency) of TA (Traffic Announcement) activeert. • Wanneer uw auto is uitgerust met een FM/MW/ LW-antenne in de achterruit/voorruit, moet u de antennevoedingskabel (blauw) of de hulpvoedingskabel (rood) aansluiten op de voedingsingang van de bestaande antenneversterker. Raadpleeg uw dealer voor meer details. • Met dit apparaat is het niet mogelijk een automatische antenne zonder relaishuis te gebruiken. Instandhouden van het geheugen Zolang de gele stroomdraad is aangesloten, blijft de stroomvoorziening van het geheugen intact, ook wanneer het contact van de auto wordt uitgeschakeld. Opmerkingen betreffende het aansluiten van de luidsprekers • Zorg dat het apparaat is uitgeschakeld, alvorens de luidsprekers aan te sluiten. • Gebruik luidsprekers met een impedantie van 4 tot 8 Ohm en let op dat die het vermogen van de versterker kunnen verwerken. Als dit wordt verzuimd, kunnen de luidsprekers ernstig beschadigd raken. • Verbind in geen geval de aansluitingen van de luidsprekers met het chassis van de auto en sluit de aansluitingen van de rechter en linker luidspreker niet op elkaar aan. • Verbind de massakabel van dit toestel niet met de negatieve (–) aansluiting van de luidspreker. • Probeer nooit de luidsprekers parallel aan te sluiten. • Sluit geen actieve luidsprekers (met ingebouwde versterkers) aan op de luidspreker-aansluiting van dit apparaat. Dit zal leiden tot beschadiging van de actieve luidsprekers. Sluit dus altijd uitsluitend luidsprekers zonder ingebouwde versterker aan. • Om defecten te vermijden mag u de bestaande luidsprekerbedrading in uw auto niet gebruiken wanneer er een gemeenschappelijke negatieve (–) draad is voor de rechter en linker luidsprekers. • Verbind de luidsprekerdraden niet met elkaar. Attenzione • Questo apparecchio è stato progettato per l’uso solo a 12 V CC con massa negativa. • Evitare che i cavi rimangano bloccati da una vite o incastrati nelle parti mobili (ad esempio nelle guide scorrevoli dei sedili). • Prima di effettuare i collegamenti, spegnere il motore dell’automobile onde evitare di causare cortocircuiti. • Collegare il cavo di collegamento dell’alimentazione 8 all’apparecchio e ai diffusori prima di collegarlo al connettore di alimentazione ausiliare. • Portare tutti i cavi di massa a un punto di massa comune. • Per sicurezza, assicurarsi di isolare qualsiasi cavo non collegato mediante apposito nastro. Note sul cavo di alimentazione (giallo) • Se questo apparecchio viene collegato con altri componenti stereo, la potenza nominale dei circuiti dell’automobile deve essere superiore a quella prodotta dalla somma dei fusibili di ciascun componente. • Se la potenza nominale dei circuiti dell’automobile non è sufficiente, collegare l’apparecchio direttamente alla batteria. Elenco dei componenti (1) I numeri nella lista corrispondono a quelli riportati nelle istruzioni. Per informazioni sull’utilizzo del tasto di rilascio qs, vedere le istruzioni per l’uso in dotazione. Attenzione Maneggiare la staffa 1 con cautela per evitare di ferirsi le mani. Esempi di collegamento (2) Note (2-A) • Assicurarsi di collegare il cavo di terra prima di collegare l’apparecchio all’amplificatore. • Se si collega un amplificatore di potenza opzionale e non si utilizza l’amplificatore incorporato, il segnale acustico verrà disattivato. Suggerimento (2-B- ) Per collegare due o più cambia CD/MD, si deve utilizzare il selettore di fonte XA-C30 (opzionale). Schema di collegamento (3) A A AMP REMOTE IN di un amplificatore di potenza opzionale Questo collegamento è riservato esclusivamente agli amplificatori. Non collegare un tipo di sistema diverso onde evitare di causare danni all’apparecchio. B Al cavo interfaccia di un telefono per auto Avvertenza Quando si collega l’apparecchio con il cavo di alimentazione in dotazione 8, si potrebbe danneggiare l’antenna elettrica se questa non ha la scatola di relè. Note sui cavi di controllo • Il cavo di controllo dell’antenna elettrica (blu) fornisce corrente continua +12 V CC quando si accende il sintonizzatore o quando si attiva la funzione AF (frequenza alternativa) o TA (notiziario sul traffico). • Se l’automobile è dotata di antenna FM/MW/LW incorporata nel vetro posteriore/laterale, collegare il cavo (blu) di controllo dell’antenna elettrica o il cavo (rosso) di ingresso dell’alimentazione opzionale al terminale di alimentazione del preamplificatore dell’antenna esistente. Per ulteriori informazioni, consultare il proprio fornitore. • Non è possibile usare un’antenna elettrica senza scatola a relè con questo apparecchio. Collegamento per la conservazione della memoria Quando il cavo di ingresso alimentazione giallo è collegato, viene sempre fornita alimentazione al circuito di memoria anche quando la chiavetta a accensione è spenta. Note sul collegamento dei diffusori • Prima di collegare i diffusori spegnere l’apparecchio. • Usare diffusori di impedenza compresa tra 4 e 8 ohm e con capacità di potenza adeguata, altrimenti i diffusori potrebbero venir danneggiati. • Non collegare i terminali del sistema diffusori al telaio dell’auto e non collegare i terminali del diffusore destro a quelli del diffusore sinistro. • Non collegare il cavo di terra di questo apparecchio al terminale negativo (–) del diffusore. • Non collegare i diffusori in parallelo. • Non collegare alcun diffusore attivo (con amplificatore incorporato) ai terminali dei diffusori dell’apparecchio perché si potrebbero danneggiare i diffusori attivi. Assicurarsi di collegare diffusori passivi a questi terminali. • Per evitare problemi di funzionamento, non utilizzare i cavi dei diffusori incorporati installati nell’automobile se il terminale dell’apparecchio condivide un cavo comune negativo (–) per i diffusori destro e sinistro. • Non collegare fra loro i cavi dei diffusori dell’apparecchio. AUDIO OUT FRONT AUDIO OUT REAR BUS AUDIO IN BUS CONTROL IN BUS AUDIO IN BUS CONTROL IN continuous power supply permanente Stromversorgung alimentation continue alimentazione continua continu voeding power aerial control Motorantenne antenne électrique comando dell’antenna elettrica automatische antenne switched illumination power supply geschaltete Beleuchtungsstromversorgung alimentation de l’éclairage commuté alimentazione a illuminazione commutata geschakelde verlichting stroomvoorziening 7 8 Red Rot Rouge Rosso Rood Black Schwarz Noir Nero Zwart switched power supply geschaltete Stromversorgung alimentation commutée alimentazione commutata geschakelde voeding earth Masse masse terra aarding Source selector (not supplied) Signalquellenwähler (nicht mitgeliefert) Sélecteur de source (non fourni) Selettore di fonte (non in dotazione) Geluidsbronkiezer (niet bijgeleverd) XA-C30 Supplied with the CD/MD changer Mit dem CD/MD-Wechsler geliefert Fourni avec le changeur de CD/MD In dotazione con il cambia CD/MD Geleverd met de CD/MD-wisselaar Supplied with XA-C30 Mit dem XA-C30 geliefert Fourni avec le XA-C30 In dotazione con il modello XA-C30 Geleverd met de XA-C30 *2 *2 6 from car aerial*1 von Autoantenne*1 de l’antenne de la voiture*1 dall’antenna dell’auto*1 van een auto-antenne*1 Fuse (10 A) Sicherung (10 A) Fusible (10 A) Fusibile (10 A) Zekering (10 A) 8 AUDIO OUT REAR BUS AUDIO IN AUDIO OUT FRONT REMOTE IN BUS CONTROL IN AMP REM Max. supply current 0.3 A max. Versorgungsstrom 0,3 A Courant max. fourni 0,3 A Alimentazione massima fornita 0,3 A Max. voedingsstroom 0,3 A Light blue Hellblau Bleu ciel Azzurro Hemelsblauw Blue/white striped Blau-weiß gestreift Rayé bleu/blanc A strisce blu e bianche Blauw/wit gestreept 1 2 3 4 Speaker, Rear, Right Lautsprecher hinten rechts haut-parleur, arrière, droit Diffusore, posteriore, destro Luidspreker, achter, rechts Speaker, Rear, Right Lautsprecher hinten rechts haut-parleur, arrière, droit Diffusore, posteriore, destro Luidspreker, achter, rechts Speaker, Front, Right Lautsprecher vorne rechts haut-parleur, avant, droit Diffusore, anteriore, destro Luidspreker, voor, rechts Speaker, Front, Right Lautsprecher vorne rechts haut-parleur, avant, droit Diffusore, anteriore, destro Luidspreker, voor, rechts 5 6 7 8 Speaker, Front, Left Lautsprecher vorne links haut-parleur, avant, gauche Diffusore, anteriore, sinistro Luidspreker, voor, links Speaker, Front, Left Lautsprecher vorne links haut-parleur, avant, gauche Diffusore, anteriore, sinistro Luidspreker, voor, links Speaker, Rear, Left Lautsprecher hinten links haut-parleur, arrière, gauche Diffusore, posteriore, sinistro Luidspreker, achter, links Speaker, Rear, Left Lautsprecher hinten links haut-parleur, arrière, gauche Diffusore, posteriore, sinistro Luidspreker, achter, links Purple Violett Mauve Viola Paars Negative polarity positions 2, 4, 6, and 8 have striped cords. An den negativ gepolten Positionen (2, 4, 6 und 8) befinden sich gestreifte Adern. Les positions de polarité négative 2, 4, 6 et 8 sont dotées de cordons rayés. Le posizioni a polarità negativa 2, 4, 6 e 8 hanno cavi rigati. De negatieve posities 2, 4, 6 en 8 hebben gestreepte kabels. Green Grün Vert Verde Groen White Weiß Blanc Bianco Wit Grey Grau Gris Grigio Grijs + – + – + – + – *1 Note for the aerial connecting If your car aerial is an ISO (International Organisation for Standardisation) type, use the supplied adaptor 6 to connect it. First connect the car aerial to the supplied adaptor, then connect it to the aerial jack of the master unit. *2 RCA pin cord (not supplied) *3 CDX-M770 only *4 Auxiliary equipment such as portable DVD player DVP-FX1 (not supplied) *5 supplied with the auxialiry equipment *6 Be sure to match the colour-coded code for audio to the appropriate jacks from the unit. *7 CDX-M670,MDX-M690 only *8 Insert with the cord upwards *1 Hinweis zum Anschließen der Antenne Wenn Ihre Fahrzeugantenne der ISO-Norm (ISO = International Organization for Standardization - Internationale Normungsgemeinschaft) entspricht, schließen Sie sie mit Hilfe des mitgelieferten Adapters 6 an. Verbinden Sie zuerst die Fahrzeugantenne mit dem mitgelieferten Adapter, und verbinden Sie diesen dann mit der Antennenbuchse des Hauptgeräts. *2 Cinchkabel (nicht mitgeliefert) *3 nur CDX-M770 *4 Zusätzliche Geräte wie z. B. der tragbare DVD-Player DVP- FX1 *5 mit den Zusatzgeräten mitgeliefert *6 Achten Sie darauf, das farbcodierte Audiokabel mit den richtigen Buchsen am Gerät zu verbinden. *7 nur CDX-M670 und MDX-M690 *8 Mit dem kabel nach oben einsetzen! *1 Remarque sur le raccordement de l’antenne Si votre antenne de voiture est de type ISO (organisation internationale de normalisation), utilisez l’adaptateur fourni 6 pour la raccorder. Raccordez d’abord l’antenne de voiture à l’adaptateur fourni et, ensuite, à la prise d’antenne de l’appareil principal. *2 Cordon à broche RCA (non fourni) *3 CDX-M770 uniquement *4 Equipement auxiliaire en option tel que le lecteur portable DVD DVP-FX1 *5 fourni avec l’équipement auxiliaire *6 Veillez à faire correspondre le code couleur audio aux fiches de l’appareil. *7 CDX-M670,MDX-M690 uniquement *8 Insérez avec le câble vers le haut from the car’s speaker connector vom Lautsprecheranschluß des Fahrzeugs du connecteur de haut-parleur de la voiture dal connettore del diffusore dell’auto van de autoluidsprekerstekker from the car’s power connector vom Stromanschluß des Fahrzeugs du connecteur d’alimentation de la voiture dal connettore di alimentazione dell’auto van de autovoedingsstekker A ATT B Source selector* Signalquellenwähler* Sélecteur de source* Selettore di fonte* Geluidsbronkiezer* * not supplied nicht mitgeliefert non fournis non in dotazione niet bijgeleverd See “Power Connection diagram” on the reverse side for details. Näheres dazu finden Sie im “Stromanschlußdiagramm”. Blättern Sie dazu bitte um. Voir le “Schéma de connexion d’alimentation” au verso pour plus de détails. Per ulteriori informazioni, vedere “Diagramma dei collegamenti di alimentazione” che si trova sul retro. Zie “Voedingsaansluitschema” op de achterkant voor meer details. Positions 1, 2 and 3 do not have pins. An Position 1, 2 und 3 befinden sich keine Stifte. Les positions 1, 2 et 3 ne comportent pas de broches. Le posizioni 1, 2 e 3 non hanno piedini. De posities 1, 2 en 3 hebben geen pins. *8 Active subwoofer Haut-parleur d’extrêmes- graves actif Aktiver Tiefsttöner Actieve subwoofer Subwoofer attivo SUB OUT DAB tuner unit* Syntoniseur DAB* DAB-Tunereinheit* DAB tuner* Sintonizzatore DAB* XT-100DAB SUB OUT (MONO) *2 9* qa* 0* qs Installation/Connections Installation/Anschluß Installation/Connexions Installazione/Collegamenti Montage/Aansluitingen FM/MW/LW Compact Disc Player CDX-M770 CDX-M670 FM/MW/LW Mini Disc Player MDX-M690 Yellow Gelb Jaune Giallo Geel Blue Blau Bleu Blu Blauw Orange/White Orange-weiß gestreift Rayé orange/ blanc Arancione/ bianco Oranje/wit 4 5 6 AUX-IN (AUDIO)*6 × 2 * supplied with CDX-M770 only * nur mit dem CDX-M770 mitgeliefert * fourni avec le modèle CDX-M770 uniquement * in dotazione solo con il modello CDX-M770 * alleen meegeleverd met CDX-M770 *5 *4 *1 Nota per il collegamento dell’antenna Se la vostra antenna della macchina è di tipo ISO (International Organization Standardization), utilizzare l’adattatore 6 in dotazione per collegarla. Collegare prima l’antenna della macchina all’adattatore in dotazione, quindi collegarla alla presa dell’antenna dell’apparecchio principale. *2 Cavo a piedini RCA (non in dotazione) *3 solo CDX-M770 *4 Apparecchio opzionale ausiliario quale il lettore DVD portatile DVP-FX1 *5 in dotazione con l’apparecchio ausiliario *6 Assicurarsi che i cavi differenziati in base al colore per l’audio corrispondano alle prese appropriate dell’apparecchio. *7 solo CDX-M670,MDX-M690 *8 Inserire con il cavo rivolto verso l’alto *1 Opmerking bij de antenne-aansluiting Indien uw wagen is uitgerust met een antenne van het type ISO (International Organisation for Standardization), moet u die aansluiten met behulp van de meegeleverde adaptor 6. Sluit eerst de auto-antenne aan op de meegeleverde adaptor en vervolgens de antennestekker op het hoofdtoestel. *2 Tulpstekkersnoer (niet bijgeleverd) *3 alleen CDX-M770 *4 Los verkrijgbare apparatuur zoals de draagbare DVD- speler DVP-FX1 *5 meegeleverd met de los verkrijgbare apparatuur *6 Zorg ervoor dat de kleurcode voor audio overeenkomt met de betreffende aansluitingen op het toestel. *7 alleen CDX-M670, MDX-M690 *8 Inbrengen met het snoer naar boven CDX-M770 is equipped with wireless rotary commander RM-X5S. Das Modell CDX-M770 ist mit dem drahtlosen Joystick RM-X5S ausgestattet. Le CDX-M770 est équipé du satellite de commande RM-X5S. Il modello CDX-M770 è dotato del telecomando a rotazione senza filo RM-X5S. De CDX-M770 is uitgerust met de draadloze bedieningssatelliet RM-X5S. *3 *7

Operating Instructions Manual de instrucciones Bruksanvisning Manual de instruções Oδηγίες Λειτυργίας Инструкция по эксплуатации For installation and connections, see the supplied installation/connections manual. Para obtener información sobre la instalación y las conexiones, consulte el manual de instalación/conexiones suministrado. Vi hänvisar till det medföljande häftet angående montering/anslutningar. Para a instalação e as ligações, consulte o manual de instalação/ligações fornecido. Για την εγκατάσταση και τις συνδέσεις, δείτε τ συνδευτικ εγειρίδι Εγκατάσταση/Συνδέσεις. Перед установкой и подсоединениями прочитайте прилагаемую инструкцию по установке и подсоединению. © 2001 Sony Corporation GB ES SE PT GR RU 3-230-448-21 (1) FM/MW/LW Compact-/Mini- Disc Player FM/MW/LW Compact Disc Player CDX-M770 CDX-M670 FM/MW/LW Mini Disc Player MDX-M690

1 Ver 1.1 2003. 10 Model Name Using Similar Mechanism CDX-M700R/M750 CD Drive Mechanism Type MG-383V-121//K Optical Pick-up Name KSS-720A SERVICE MANUAL US Model AEP Model UK Model E Model CDX-M770 • The tuner and CD sections have no adjustments. AUDIO POWER SPECIFICATIONS (US MODEL) POWER OUTPUT AND TOTAL HARMONIC DISTORTION 23.2 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 5% total harmonic distortion. CD player section Signal-to-noise ratio 90 dB Frequency response 10 – 20,000 Hz Wow and flutter Below measurable limit Laser Diode Properties (US model) Material GaAlAs Wavelength 780 nm Emission Duration Continuous Laser output power Less than 44.6 µW* * This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block. Tuner section FM Tuning range 87.5 – 107.9 MHz (US model) 87.5 – 108.0 MHz (AEP, UK, E model) Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Usable sensitivity 8 dBf Selectivity 75 dB at 400 kHz Signal-to-noise ratio 66 dB (stereo), 72 dB (mono) Harmonic distortion at 1 kHz 0.6% (stereo), 0.3% (mono) Separation 35 dB at 1 kHz Frequency response 30 – 15,000 Hz AM (US model) Tuning range 530 – 1,710 kHz Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity 30 µV SPECIFICATIONS MW/LW (AEP, UK, E model) Tuning range MW: 531 – 1,602 kHz LW: 153 – 279 kHz Aerial terminal External aerial connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity MW: 30 µV LW: 40 µV Power amplifier section Outputs Speaker outputs (sure seal connectors) Speaker impedance 4 – 8 ohms Maximum power output 52 W × 4 (at 4 ohms) General Outputs Audio outputs (front/rear) Subwoofer output (mono) Power antenna relay control lead (US model) Power aerial relay control lead (AEP, UK, E model) Power amplifier control lead FM/AM COMPACT DISC PLAYER US Model FM/MW/LW COMPACT DISC PLAYER AEP, UK, E Model – Continued on next page – Sony Corporation e Vehicle Company Published by Sony Engineering Corporation 9-873-504-12 2003J04-1 © 2003. 10

Operating Instructions XM Satellite Radio Receiver XT-XM1 Sony Corporation © 2002 Printed in Japan Owner’s Record The model number is located on the bottom and serial number also on the bottom. Record the serial number in the space provide below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. XT-XM1 Serial No. XM Radio ID You need to subscribe for XMTM Satellite Radio Service to listen to the radio broadcast. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. 3-243-168-11 (1) If you have any questions or problem concerning this product, consult your nearest Sony dealer. If you have any questions or problem concerning the XM Satellite radio service including the broadcast, consult XM. The XM Radio ID (XM-ID) is required when consulting XM. It is located on the bottom of the main unit, and you can also check it in the display of this unit (see “Displaying the XM Radio ID”). Welcome! Thank you for purchasing the Sony XM Satellite Radio Receiver. The receiver allows you to: •Receive XM Satellite Radio programming (with subscription) by connecting a Sony master unit* compatible with the Sony BUS system. •Connect and use an optional CD or MD changer. •Receive up to 100 channels of XM programming. •Display channel name, artist name, and song title for most XM channels. •Store up to 20 favorite XM channels. •Search XM channels by category. * Some master units may not be connected to this receiver. (For details, please consult your nearest Sony dealer.) Introducing XMTM Satellite Radio There’s a world beyond AM and FM. XM Satellite Radio. Up to 100 channels. Coast-to- Coast Coverage. Digital quality sound. With many commercial-free music channels. Plus, the best sports, comedy, talk, news and entertainment, including USA Today, Discovery Radio, NASCAR, Sesame Workshop, CNNfn and CNN/SI. Questions? Visit www.xmradio.com. The future is waiting. How to Subscribe Listeners can subscribe by visiting XM on the Web at www.xmradio.com or by calling XM’s Listener Care at (800)852-9696. Customers should have their Radio ID ready; it is located on the bottom of the main unit, and you can also check it in the display of this unit (see “Displaying the XM Radio ID”). Technology. It is prohibited to copy, decompile, disassemble, reverse engineer or manipulate any technology incorporated in receivers compatible with the XM Satellite Radio system. Furthermore, the AMBE® voice compression software included in this product is protected by intellectual property rights including patent rights, copyrights, and trade secrets of Digital Voice Systems, Inc. The user of this or any other software contained in an XM Radio is explicitly prohibited from attempting to copy, decompile, reverse engineer, or disassemble the object code, or in any other way convert the object code into human-readableform. The software is licensed solely for use within this product. Getting Started Resetting the master unit Before operating the XM receiver for the first time, reset the master unit. If the unit is not reset in this manner, it may not function properly. For details on how to reset it, refer to the operating instructions of the master unit. Caution For the following master units, press the Repeat (REP) button of the master unit for two seconds after turning the XM on and select “setup 2.” Without this procedure, the master unit will not display tuning-in information from the receiver correctly. Except for the following master units, “setup 1” is selected in the factory settings. CDX-C8050X CDX-C800REC* CDX-M750 CDX-M650 CDX-M610 CDX-M600 MDX-C8500X XR-M550 * You may observe flickering in parts of the display while performing operations. This is not malfunction. Note Resetting the master unit will erase the clock setting and some stored contents of the master unit. Using category search to locate channels Each XM channel is associated with a category that describes the type of music or programming that is played on the channel. Examples of categories include “rock,” “jazz,” “news,” and so on. Users unfamiliar with XM’s programming may use the radio’s search-by-category function to select channels. 1 Press the Repeat (REP) button to enter category search mode. The category of the current channel is displayed. With some master units, the Repeat button is only equipped on the remote control. 2 Press the Disc/Preset buttons repeatedly until you find the desired category. 3 Press the Seek buttons repeatedly until you find the desired channel in that category. The display shows “CAT SRCH” to indicate that the radio is in category search mode. While in this mode, you will only be able to tune to channels in the selected category. You may use the Disc/Preset buttons to choose other categories. 4 To exit from category search mode and return to the normal mode, press the Repeat (REP) button. The radio automatically returns to the normal mode if there no key is pressed within 5 seconds. Storing favorite channels You can preset up to 20 channels. 1 Tune in a channel that you want to store. 2 Press the Shuffle (SHUF) button. The radio will show a list of presets, starting with preset number 1. The preset number will be shown if a channel has already been stored into the preset. With some master units, the Shuffle button is only equipped on the remote control. 3 Press the Disc/Preset button to select a preset number. With some master units, the Disc/Preset button is only equipped on the remote control. 4 Press the Disc/Preset + (Disc +) button for 2 seconds. The display shows “MEMORY” if the radio successfully stores the channel into the preset. The display shows “FAILURE” if the radio fails to store the channel into the preset. The radio automatically returns to the normal mode if there no key is pressed within 5 seconds. Receiving a stored channel • Press either Disc/Preset button to select the preset channel you want to listen to. • Press the Shuffle (SHUF) button. Press the Disc/Preset + (DISC +) button to select the preset channel and then press the SEEK + or SEEK – button to start. Displaying the XM Radio ID 1 During XM Satellite Radio reception, press the Seek button to select “CHANNEL 1.” 2 Press the “Seek – (down)” button. “RADIO ID” is indicated for 2 seconds and the XM Radio ID number is indicated for 10 seconds. These indications will be displayed alternately. To cancel the XM Radio ID display, press the Seek button to select a channel. Basic Operations Listening to a program The XM receiver is controlled by the master unit. Button locations vary with different master unit models. Please refer to the master unit instruction manuals. 1 To select XM: a. Press the Source button until “XM” is displayed. -or- b. Press the Source button until “MD” is displayed, then press the Mode button to select XM. For master units which can control more than one MD changer, press the Mode button repeatedly (the display will show “MD1,” “MD2,” etc.) until the receiver is found. 2 Press either Seek button to select the desired channel. Pressing and holding the Seek button will quickly step through the channels. Note “LOADING” is indicated while the receiver is reading the information. Display items The XM Satellite Radio information (Channel Name, Channel Number, Artist Name/Program Name and Song Title) is available on the display. Press the Display (DSPL) button. Each time you press the Display (DSPL) button, the item changes as follows: Channel Name t Channel Number t Artist Name/Program Name t Song Title t For MEX-5DI, press the ENTER button of the remote control to change the display item. Notes • While Artist Name/Program Name or Song Title is displayed, if you select a channel, Channel Name will be displayed for 2 to 3 seconds and then return to the previous display. • If there is no information about Artist Name/ Program Name or Song Title, “- - - -” will be displayed. • During XM Satellite Radio reception, Spectrum Analyzer, Dual Information, Motion Display function of the master unit cannot be operated. • The display indicates up to 8 characters. The characters on the display cannot be scrolled even when the Auto Scroll function of the master unit is set to on. • You cannot display the clock during XM Satellite Radio reception on a master unit whose clock display is shown by pressing the Display (DSPL) button. Additional Information Specifications Frequency 2332.5 – 2345.0 MHz Power requirements 12 V DC car battery (negative ground) Outputs BUS control output Audio output Inputs Antenna input (Satellite, Terrestrial) BUS control input Audio input Dimensions 224 × 37.8 × 160 mm (8 7/8 × 1 1/2 × 6 3/8 in.) (w/h/d) Mass Approx. 1.0 kg (2 lb. 4 oz.) Supplied accessories Parts for installation and connection (1 set) Design and specifications are subject to change without notice. Troubleshooting Should any problem persist after you have made the following checks, consult your nearest Sony dealer. Consult XM if you have any questions or problem concerning the broadcast service of the XM Satellite radio. The information on the display cannot be changed during XM Satellite Radio reception. •Refer to “Caution” in “Getting Started.” No sound. •Adjust the volume control of the master unit. •Cancel the attenuate function of the master unit. •The connecting cords are not connected properly. The sound is hampered by noises. Locate codes and cables such as an antenna code, a BUS cable, an RCA pin code, or a power code so as they do not interfere each other. The channels cannot be received. Check the connection of the receiver and the antenna. Advisory Message When a problem occurs with the receiver, an error message will be indicated on the display of the master unit. ANTENNA The antenna is not connected properly. t Check the connection of the receiver and the antenna. UPDATING You have not subscribed to XM, or the channel is not authorized. t You need to subscribe to XM. NO SIGNL XM signal is too weak. t Move to another area where your system can receive the signal. OFF AIR The channel is not broadcasted now. t Select another channel. LOADING The receiver is reading the channel information t Wait until the receiver completes receiving the information. “– – – –” or “CH – – –” •The channel to be tuned-in is void due to the change by the broadcast service, or the receiving condition is not good. •There is no text information or time information in the channel. This is not an error.