Sony CDX-M9900 Operating Instructions (primary manual) Manuals

AUDIO OUT FRONT SUB OUT AUDIO OUT REAR VIDEO IN ©2004 Sony Corporation Printed in Korea CDX-M9900 3-265-746-31 (1) Installation/Connections 安裝／線路連接 FM/MW/LW Compact Disc Player 3 2 Equipment used in illustrations (not supplied) 插圖中的裝置（非附送） Rear speaker 後揚聲器 Front speaker 前揚聲器 Active subwoofer 有源超低音揚聲器 5 4 CD/MD changer CD/MD 換碟機 × 4 1 B VIDEO IN BUS AUDIO IN/AUX IN* BUS CONTROL IN VIDEO IN BUS AUDIO IN/AUX IN*1 BUS CONTROL IN Source selector*2 音源選擇器*2 XA-C30 *1 Use the AUX-IN selector XA-300 (not supplied) when you want to connect the audio outputs of a DVD player to the BUS AUDIO IN/AUX IN terminal. *2 not supplied *1 若您想要將DVD播放機的音頻 輸出連接至BUS AUDIO IN/AUX IN端子，則使用AUX-IN選擇器 XA-300（不附帶）。 *2 非附送 A × 2 Power amplifier 功率放大器 6 Catch DVD player DVX-11A DVD 播放機 DVX-11A 7 2 1 Rotary commander RM-X4S 旋轉式控制器 RM-X4S Cautions •This unit is designed for negative earth 12 V DC operation only. •Do not get the leads under a screw, or caught in moving parts (e.g., seat railing). •Before making connections, turn the car ignition off to avoid short circuits. •Connect the yellow and red power input leads only after all other leads have been connected. •Run all earth leads to a common earth point. •Be sure to insulate any loose unconnected leads with electrical tape for safety. Notes on the power supply lead (yellow) •When connecting this unit in combination with other stereo components, the connected car circuit’s rating must be higher than the sum of each component’s fuse. •When no car circuits are rated high enough, connect the unit directly to the battery. Parts Iist (1) •The numbers in the list are keyed to those in the instructions. •The bracket 1 is attached to the unit before shipping. Before mounting the unit, use the release keys 8 to remove the bracket 1 from the unit. For details, see “Removing the bracket (5)” on the reverse side of the sheet. • Keep the release keys 8 for future use as they are also necessary if you remove the unit from your car. Caution Handle the bracket 1 carefully to avoid injuring your fingers. Note Before installing, make sure that the catches on both sides of the bracket 1 are bent inwards 2 mm. If the catches are straight or bent outwards, the unit will not be installed securely and may spring out. Connection example (2) Notes (2-A) • Be sure to connect the black earth lead before connecting the amplifier. • If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be deactivated. Tip (2-B- ) For connecting two or more CD/MD changers, the source selector XA-C30 (optional) is necessary. Connection diagram (3) 1 To a metal surface of the car First connect the black earth lead, then connect the orange/white striped, yellow, and red power input leads. 2 To the power aerial control lead or power supply lead of aerial booster amplifier Notes • It is not necessary to connect this lead if there is no power aerial or aerial booster, or with a manually-operated telescopic aerial. • When your car has a built-in FM/MW/LW aerial in the rear/side glass, see “Notes on the control and power supply leads.” 3 To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit. 4 To the interface cable of a car telephone 5 To a car’s illumination signal Be sure to connect the black earth lead to a metal surface of the car first. 6 To the +12 V power terminal which is energised in the accessory position of the ignition key switch Notes • If there is no accessory position, connect to the +12 V power (battery) terminal which is energised at all times. Be sure to connect the black earth lead to a metal surface of the car first. • When your car has a built-in FM/MW/LW aerial in the rear/side glass, see “Notes on the control and power supply leads.” 7 To the +12 V power terminal which is energised at all times Be sure to connect the black earth lead to a metal surface of the car first. 8 To the parking brake switch cord 1 8 9 * Use the AUX-IN selector XA- 300 (not supplied) when you want to connect the audio outputs of a DVD player to the BUS AUDIO IN/ AUX IN terminal. * 若您想要將D V D 播放機的音頻 輸出連接至BUS AUDIO IN/AUX IN端子，則使用AUX-IN選擇器 XA-300（不附帶）。

Operating Instructions Bedienungsanleitung Mode d’emploi Istruzioni per l’uso Gebruiksaanwijzing 3-265-745-21 (1) Wichtig! Bitte nehmen Sie sich etwas Zeit, um den Geräte-Pass vollständig auszufüllen. Dieser befindet sich auf der hinteren Umschlagseite dieser Bedienungsanleitung. Si dichiara che l’apparecchio è stato fabbricato in conformità all’art. 2, Comma 1 del D.M. 28.08. 1995 n. 548. CDX-M9900 For installation and connections, see the supplied installation/connections manual. Zur Installation und zum Anschluss siehe die mitgelieferte Installations-/Anschlussanleitung. En ce qui concerne l’installation et les connexions, consulter le manuel d’installation/ raccordement fourni. Per l’installazione e i collegamenti, fare riferimento al manuale di istruzioni per l’installazione e i collegamenti in dotazione. Zie voor het monteren en aansluiten van het apparaat de bijgeleverde handleiding "Installatie en aansluitingen". © 2004 Sony Corporation NL IT FR DE GB FM/MW/LW Compact Disc Player FM/MW/LW Compact Disc Player

Operating Instructions Mode d’emploi US FR 3-265-745-11 (1) Owner’s Record The model and serial numbers are located on the bottom of the unit. Record these numbers in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. CDX-M9900 Serial No. CDX-M9900 For installation and connections, see the supplied installation/connections manual. En ce qui concerne l’installation et les connexions, consulter le manuel d’installation/ raccordement fourni. © 2004 Sony Corporation FM/AM Compact Disc Player

5 7 4 8 1 3 5 7 2 4 6 8 A B C AMP REM ATT 6 SUB OUT BUS AUDIO IN/ AUX IN*9 BUS CONTROL IN REMOTE IN AUDIO OUT REAR VIDEO IN AUDIO OUT FRONT *1 RCA pin cord (not supplied) *2 Auxiliary equipment such as portable DVD player (not supplied) *3 Supplied with the auxiliary equipment *4 Be sure to match the colour-coded cord for audio to the appropriate jacks from the unit. If you connect an optional CD/MD unit, you cannot use AUX IN terminal. *5 Supplied with XA-C30 *6 Supplied with the CD/MD changer *7 Insert with the cord upwards *8 Be sure to match the colour-coded cord for audio and visual to the appropriate jacks from the unit. *9 BUS AUDIO IN and AUX IN are automatically switched depending on the equipment connected. *10 Note for the aerial connecting If your car aerial is an ISO (International Organisation for Standardisation) type, use the supplied adaptor 5 to connect it. First connect the car aerial to the supplied adaptor, then connect it to the aerial jack of the master unit. *11 For details on connecting to the parking brake switch cord, and attaching the tap 7, see “Connecting the parking brake cord (4)” on the reverse side. AUDIO OUT FRONT SUB OUT AUDIO OUT REAR VIDEO IN VIDEO IN BUS AUDIO IN/AUX IN*1 BUS CONTROL IN Source selector (not supplied) Signalquellenwähler (nicht mitgeliefert) Sélecteur de source (non fourni) Selettore di fonte (non in dotazione) Geluidsbronkiezer (niet bijgeleverd) XA-C30 5 from car aerial *10 von Autoantenne *10 de l’antenne de la voiture *10 dall’antenna dell’auto *10 van een auto-antenne *10 Fuse (10 A) Sicherung (10 A) Fusible (10 A) Fusibile (10 A) Zekering (10 A) 6 Light blue Hellblau Bleu ciel Azzurro Lichtblauw Blue/white striped Blauweiß gestreift Rayé bleu/blanc Rigato blu e bianco Blauw/wit gestreept Max. supply current 0.3 A max. Versorgungsstrom 0,3 A Courant d’alimentation maximum 0,3 A Alimentazione massima fornita 0,3 A Max. voedingsstroom 0,3 A Let op! •Dit apparaat is ontworpen voor gebruik op gelijkstroom van een 12 Volts auto-accu, negatief geaard. •Zorg ervoor dat de draden niet onder een schroef of tussen bewegende onderdelen (b.v. zetelrail) terechtkomen. •Alvorens aansluitingen te verrichten moet u het contact uitzetten om kortsluiting te vermijden. •Sluit het netsnoer 6 aan op het apparaat en de luidsprekers voordat u dit op de hulpvoedingsaansluiting aansluit. •Sluit alle aarddraden op een gemeenschappelijk aardpunt aan. •Voorzie niet aangesloten draden om veiligheidsredenen altijd van isolatietape. Opmerkingen bij de voedingskabel (geel) •Wanneer u dit apparaat aansluit samen met andere componenten, moet het vermogen van de aangesloten autostroomkring groter zijn dan de som van de zekeringen van elke component afzonderlijk. •Wanneer het vermogen onvoldoende is, moet u het apparaat rechtstreeks aansluiten op de accu. Onderdelenlijst (1) •De nummers in de afbeelding verwijzen naar die in de montage- aanwijzingen. •De beugel 1 en de beschermende rand 4 worden bevestigd op het apparaat voordat dit wordt verzonden. Voordat u het apparaat plaatst, moet u de ontgrendelingssleutels 8 gebruiken om de beugel 1 en de beschermende rand 4 te verwijderen van het apparaat. Zie "De beschermende rand en de beugel verwijderen (5)" aan de achterzijde van dit vel voor meer informatie. •Bewaar de ontgrendelingssleutels 8 voor toekomstig gebruik omdat u deze ook nodig hebt om het apparaat uit de auto te verwijderen. Let op Houd de beugel 1 voorzichtig vast zodat u uw vingers niet verwondt. Opmerking Voordat u het apparaat installeert, moet u de grepen aan beide zijden van de beugel 1 2 mm naar binnen buigen. Als de grepen recht zijn of naar buiten gebogen, kan het apparaat niet goed worden bevestigd en kan dit losschieten. Voorbeeldaansluitingen (2) Opmerkingen (2-A) • Sluit eerst de aardingskabel aan alvorens de versterker aan te sluiten. • Wanneer u een optionele eindversterker aansluit en de ingebouwde versterker niet gebruikt, wordt de pieptoon uitgeschakeld. Tip (2-B- ) Om twee of meer CD/MD-wisselaars aan te sluiten, hebt u de geluidsbronkiezer XA-C30 (optioneel) nodig. Aansluitschema (3) A Naar AMP REMOTE IN van een optionele eindversterker Deze aansluiting is alleen bedoeld voor versterkers. Door een ander systeem aan te sluiten kan het apparaat worden beschadigd. B Naar het interface-snoer van een autotelefoon C Naar het schakelsnoer van de parkeerrem Let op Indien u een elektrische antenne hebt zonder relaisdoos, kan het aansluiten van deze eenheid met het bijgeleverde netsnoer 6 de antenne beschadigen. Opmerkingen betreffende de aansluitsnoeren • De antennevoedingskabel (blauw) levert +12 V gelijkstroom wanneer u de tuner inschakelt of de AF (Alternative Frequency) of TA (Traffic Announcement) functie activeert. • Wanneer uw auto is uitgerust met een FM/MW/LW-antenne in de achterruit/voorruit, moet u de antennevoedingskabel (blauw) of de hulpvoedingskabel (rood) aansluiten op de voedingsingang van de bestaande antenneversterker. Raadpleeg uw dealer voor meer details. • Met dit apparaat is het niet mogelijk een automatische antenne zonder relaisdoos te gebruiken. Instandhouden van het geheugen Zolang de gele stroomdraad is aangesloten, blijft de stroomvoorziening van het geheugen intact, ook wanneer het contact van de auto wordt uitgeschakeld. Opmerkingen betreffende het aansluiten van de luidsprekers • Zorg dat het apparaat is uitgeschakeld, alvorens de luidsprekers aan te sluiten. • Gebruik luidsprekers met een impedantie van 4 tot 8 Ohm en let op dat die het vermogen van de versterker kunnen verwerken. Als dit wordt verzuimd, kunnen de luidsprekers ernstig beschadigd raken. • Verbind in geen geval de aansluitingen van de luidsprekers met het chassis van de auto en sluit de aansluitingen van de rechter- en linkerluidspreker niet op elkaar aan. • Verbind de aardingskabel van dit apparaat niet met de negatieve (–) aansluiting van de luidspreker. • Probeer nooit de luidsprekers parallel aan te sluiten. • Sluit geen actieve luidsprekers (met ingebouwde versterkers) aan op de luidspreker-aansluiting van dit apparaat. Dit zal leiden tot beschadiging van de actieve luidsprekers. Sluit dus altijd uitsluitend luidsprekers zonder ingebouwde versterker aan. • Om defecten te vermijden mag u de bestaande luidsprekerbedrading in uw auto niet gebruiken wanneer er een gemeenschappelijke negatieve (–) draad is voor de rechter- en linkerluidsprekers. • Verbind de luidsprekerdraden niet met elkaar. Opmerking over aansluiten Als de luidspreker en versterker niet correct zijn aangesloten, wordt "Failure" in het display weergegeven. In dit geval moet u zorgen dat de luidspreker en versterker correct zijn aangesloten. Attenzione •Questo apparecchio è stato progettato per l’uso solo a 12 V CC con massa negativa. •Evitare che i cavi rimangano bloccati da una vite o incastrati nelle parti mobili (ad esempio nelle guide scorrevoli dei sedili). •Prima di effettuare i collegamenti, spegnere il motore dell’automobile onde evitare di causare cortocircuiti. •Collegare il cavo di collegamento dell’alimentazione 6 all’apparecchio e ai diffusori prima di collegarlo al connettore di alimentazione accessoria. •Portare tutti i cavi di massa a un punto di massa comune. •Per sicurezza, assicurarsi di isolare qualsiasi cavo non collegato utilizzando del nastro adesivo. Note sul cavo di alimentazione (giallo) •Se questo apparecchio viene collegato in combinazione con altri componenti stereo, la potenza nominale dei circuiti dell’automobile deve essere superiore a quella prodotta dalla somma dei fusibili di ciascun componente. •Se la potenza nominale dei circuiti dell’automobile non è sufficiente, collegare l’apparecchio direttamente alla batteria. Elenco dei componenti (1) •I numeri nella lista corrispondono a quelli riportati nelle istruzioni. •La staffa 1 e la cornice di protezione 4 vengono applicati all’unità in fabbrica. Prima di installare l’unità, utilizzare le chiavette di rilascio 8 per rimuovere la staffa 1 e la cornice di protezione 4 dall’apparecchio. Per ulteriori informazioni, vedere “Rimozione della staffa e della cornice di protezione (5)” sul lato opposto del foglio. •Conservare le chiavette di rilascio 8 per un uso futuro in quanto sono necessarie per rimuovere l’unità dall’auto. Attenzione Maneggiare la staffa 1 con cautela per evitare di ferirsi le mani. Nota Prima di installare l’unità, accertarsi di ripiegare i fermi presenti su entrambi i lati della staffa 1 verso l’interno di 2 mm. Se i fermi sono diritti o ripiegati verso l’esterno, l’apparecchio non verrà installato in modo sicuro e potrebbe fuoriuscire. Esempio di collegamento (2) Note (2-A) • Assicurarsi di collegare il cavo di terra prima di collegare l’amplificatore. • Se si effettua il collegamento di un amplificatore di potenza opzionale e l’amplificatore incorporato non viene utilizzato, il segnale acustico si disattiva. Suggerimento (2-B- ) Per collegare due o più cambia CD/MD, utilizzare, se necessario, il selettore di fonte XA-C30 (opzionale). Schema di collegamento (3) A A AMP REMOTE IN di un amplificatore di potenza opzionale Questo collegamento è riservato esclusivamente agli amplificatori. Non collegare un tipo di sistema diverso onde evitare di causare danni all’apparecchio. B Al cavo interfaccia di un telefono per auto C Al cavo di commutazione del freno a mano Avvertenza Se il presente apparecchio viene collegato con il cavo di collegamento dell’alimentazione in dotazione 6, è possibile che l’antenna elettrica venga danneggiata se questa non dispone di scatola a relè. Note sui cavi di controllo • Il cavo (blu) di controllo dell’antenna elettrica fornisce alimentazione pari a +12 V CC quando si attiva il sintonizzatore oppure la funzione TA (notiziario sul traffico) o AF (frequenza alternativa). • Se l’automobile è dotata di antenna FM/MW/LW incorporata nel vetro posteriore/laterale, collegare il cavo (blu) di controllo dell’antenna elettrica o il cavo (rosso) di ingresso dell’alimentazione accessoria al terminale di alimentazione del preamplificatore dell’antenna esistente. Per ulteriori informazioni, consultare il proprio fornitore. • Non è possibile usare un’antenna elettrica senza scatola a relè con questo apparecchio. Collegamento per la conservazione della memoria Quando il cavo di ingresso alimentazione giallo è collegato, viene sempre fornita alimentazione al circuito di memoria anche quando l’interruttore di accensione è spento. Note sul collegamento dei diffusori • Prima di collegare i diffusori spegnere l’apparecchio. • Usare diffusori di impedenza compresa tra 4 e 8 ohm e con capacità di potenza adeguata. Diversamente, i diffusori potrebbero venire danneggiati. • Non collegare i terminali del sistema diffusori al telaio dell’auto e non collegare i terminali del diffusore destro a quelli del diffusore sinistro. • Non collegare il cavo di terra di questo apparecchio al terminale negativo (–) del diffusore. • Non collegare i diffusori in parallelo. • Assicurarsi di collegare soltanto diffusori passivi, poiché il collegamento di diffusori attivi, dotati di amplificatori incorporati, ai terminali dei diffusori potrebbe danneggiare l’apparecchio. • Per evitare problemi di funzionamento, non utilizzare i cavi dei diffusori incorporati installati nell’automobile se l’apparecchio condivide un cavo comune negativo (–) per i diffusori destro e sinistro. • Non collegare fra loro i cavi dei diffusori dell’apparecchio. Nota sui collegamenti Se l’amplificatore e il diffusore non sono collegati correttamente, “Failure” viene visualizzato nel display. In tal caso, accertarsi che l’amplificatore e il diffusore siano collegati correttamente. Précautions •Cet appareil est conçu pour fonctionner sur un courant continu de 12 V avec masse négative. •Evitez de fixer des vis sur les câbles ou de coincer ceux-ci dans des pièces mobiles (par exemple, armature de siège). •Avant d’effectuer des raccordements, coupez le moteur pour éviter les courts-circuits. •Branchez le cordon d’alimention 6 sur l’appareil et les haut- parleurs avant de le brancher sur le connecteur d’alimentation auxiliaire. •Rassemblez tous les fils de terre en un point de masse commun. •Veillez à isoler tout fil ou câble non connecté avec du chatterton. Remarques sur le cordon d’alimentation (jaune) •Lorsque cet appareil est raccordé à d’autres éléments stéréo, la valeur nominale des circuits du véhicule raccordés doit être supérieure à la somme des fusibles de chaque élément. •Si aucun circuit de la voiture n’est assez puissant, raccordez directement l’appareil à la batterie. Liste des composants (1) •Les numéros de la liste correspondent à ceux des instructions. •Le support 1 et le tour de protection 4 sont fixés à l’appareil avant de quitter l’usine. Avant le montage de l’appareil, utilisez les clés de déblocage 8 pour détacher le support 1 et le tour de protection 4 de l’appareil. Pour de plus amples informations, reportez-vous à la section « Retrait du tour de protection et du support (5) » au verso. •Conservez les clés de déblocage 8 pour une utilisation ultérieure car vous en aurez également besoin pour retirer l’appareil de votre véhicule. Avertissements Manipulez le support 1 avec soin pour éviter de vous blesser aux doigts. Remarque Avant l’installation, assurez-vous que les loquets des deux côtés du support 1 sont bien pliés de 2 mm vers l’intérieur. Si les loquets sont droits ou pliés vers l’extérieur, l’appareil ne peut pas être fixé solidement et peut se détacher. Exemple de raccordement (2) Remarques (2-A) • Raccordez d’abord le fil de masse avant de connecter l’amplificateur. • Si vous raccordez un amplificateur de puissance en option et si vous n’utilisez pas l’amplificateur intégré, le bip sera désactivé. Conseil (2-B- ) Dans le cas du raccordement de deux changeurs de CD/MD ou plus, le sélecteur de source XA-C30 (en option) est indispensable. Schémas de raccordement (3) A Au niveau de AMP REMOTE IN d’un amplificateur de puissance facultatif Ce raccordement existe seulement pour les amplificateurs. Le raccordement à tout autre système peut endommager l’appareil. B Vers le cordon de liaison d’un téléphone de voiture C Vers le cordon du capteur du frein à main Avertissement Si vous disposez d’une antenne électrique sans boîtier de relais, le branchement de cet appareil au moyen du cordon d’alimentation fourni 6 risque d’endommager l’antenne. Remarques sur les fils de commande • Le fil de commande (bleu) fournit du courant continu de +12 V lorsque vous mettez le tuner sous tension ou lorsque vous activez la fonction AF (fréquence alternative) ou TA (informations circulation). • Lorsque votre voiture est équipée d’une antenne FM/MW(PO)/ LW(GO) intégrée dans la vitre arrière/latérale, raccordez le fil de commande de l’antenne (bleu) ou l’entrée d’alimentation des accessoires (rouge) au bornier de l’amplificateur d’antenne existant. Pour plus de détails, consultez votre revendeur. • Une antenne électrique sans boîtier de relais ne peut pas être utilisée avec cet appareil. Raccordement pour la conservation de la mémoire Lorsque le fil d’entrée d’alimentation jaune est connecté, le circuit de la mémoire est alimenté en permanence même si la clé de contact est en position d’arrêt. Remarques sur le raccordement des haut-parleurs • Avant de raccorder les haut-parleurs, mettre l’appareil hors tension. • Utiliser des haut-parleurs ayant une impédance de 4 à 8 ohms et une capacité adéquate sous peine de les endommager. • Ne pas raccorder les bornes du système de haut-parleurs au châssis de la voiture et ne pas connecter les bornes du haut-parleur droit à celles du haut-parleur gauche. • Ne pas raccorder le câble de masse de cet appareil à la borne négative (–) du haut-parleur. • Ne pas tenter de raccorder les haut-parleurs en parallèle. • Ne pas connecter d’enceintes acoustiques actives (avec amplificateurs intégrés) aux bornes d’enceinte de cet appareil, pour éviter d’endommager l’appareil. Veiller à raccorder des enceintes passives uniquement. • Pour éviter tout dysfonctionnement, n’utilisez pas les fils des haut- parleurs intégrés installés dans votre voiture si l’appareil dispose d’un fil négatif commun (–) pour les haut-parleurs droit et gauche. • Ne raccordez pas entre eux les cordons des haut-parleurs de l’appareil. Remarque sur le raccordement Si les enceintes et l’amplificateur ne sont pas raccordés correctement, le message « Failure » s’affiche. Dans ce cas, assurez-vous que les enceintes et l’amplificateur sont raccordés correctement. Vorsicht •Dieses Gerät ist ausschließlich für den Betrieb bei 12 V Gleichstrom (negative Erdung) bestimmt. •Achten Sie darauf, dass die Kabel nicht unter einer Schraube oder zwischen beweglichen Teilen wie z. B. in einer Sitzschiene eingeklemmt werden. •Schalten Sie, bevor Sie irgendwelche Anschlüsse vornehmen, die Zündung des Fahrzeugs aus, um Kurzschlüsse zu vermeiden. •Verbinden Sie das Stromversorgungskabel 6 mit dem Gerät und den Lautsprechern, bevor Sie es mit dem Hilfsstromanschluss verbinden. •Schließen Sie alle Erdungskabel an einen gemeinsamen Massepunkt an. •Aus Sicherheitsgründen müssen alle losen, nicht angeschlossenen Drähte mit Isolierband abisoliert werden. Hinweise zum Stromversorgungskabel (gelb) • Wenn Sie dieses Gerät zusammen mit anderen Stereokomponenten anschließen, muss der Autostromkreis, an den die Geräte angeschlossen sind, eine höhere Leistung aufweisen als die Summe der Sicherungen der einzelnen Komponenten. •Wenn kein Autostromkreis eine so hohe Leistung aufweist, schließen Sie das Gerät direkt an die Batterie an. Teileliste (1) •Die Nummern in der Liste sind dieselben wie im Erläuterungstext. •Die Halterung 1 und die Schutzumrandung 4 werden vor dem Ausliefern am Gerät angebracht. Bevor Sie das Gerät montieren, nehmen Sie die Halterung 1 und die Schutzumrandung 4 mithilfe der Löseschlüssel 8 bitte vom Gerät ab. Einzelheiten dazu finden Sie unter „Abnehmen der Schutzumrandung und der Halterung (5)“ auf der Rückseite dieses Blattes. •Bewahren Sie die Löseschlüssel 8 für den späteren Gebrauch auf. Sie werden z. B. benötigt, wenn Sie das Gerät aus dem Fahrzeug ausbauen wollen. Sicherheitshinweise Seien Sie beim Umgang mit der Halterung 1 vorsichtig, damit Sie sich nicht die Hände verletzen. Hinweis Vergewissern Sie sich vor dem Installieren, dass die Verriegelungen an beiden Seiten der Halterung 1 um 2 mm nach innen gebogen sind. Wenn die Verriegelungen gerade oder nach außen gebogen sind, lässt sich das Gerät nicht sicher installieren und kann herausspringen. Anschlussbeispiel (2) Hinweise (2-A) • Schließen Sie unbedingt zuerst das Massekabel an, bevor Sie den Verstärker anschließen. • Wenn Sie einen gesondert erhältlichen Endverstärker anschließen und den integrierten Verstärker nicht benutzen, wird der Signalton deaktiviert. Tipp (2-B- ) Zum Anschließen von zwei oder mehr CD/MD-Wechslern wird der gesondert erhältliche Signalquellenwähler XA-C30 benötigt. Anschlussdiagramm (3) A An AMP REMOTE IN des gesondert erhältlichen Endverstärkers Dieser Anschluss ist ausschließlich für Verstärker gedacht. Schließen Sie nichts anderes daran an. Andernfalls kann das Gerät beschädigt werden. B An Schnittstellenkabel eines Autotelefons C An die Parkbremsenschaltleitung Warnung Wenn Sie eine Motorantenne ohne Relaiskästchen verwenden, kann durch Anschließen dieses Geräts mit dem mitgelieferten Stromversorgungskabel 6 die Antenne beschädigt werden. Hinweise zu den Steuerleitungen • Die Motorantennen-Steuerleitung (blau) liefert + 12 V Gleichstrom, wenn Sie den Tuner einschalten oder die AF- (Alternativfrequenzsuche) oder die TA-Funktion (Verkehrsdurchsagen) aktivieren. • Wenn das Fahrzeug mit einer in der Heck-/Seitenfensterscheibe integrierten UKW/MW/LW-Antenne ausgestattet ist, schließen Sie die Motorantennen-Steuerleitung (blau) oder die Zubehörstromversorgungsleitung (rot) an den Stromversorgungsanschluss des vorhandenen Antennenverstärkers an. Näheres dazu erfahren Sie bei Ihrem Händler. • Es kann nur eine Motorantenne mit Relaiskästchen angeschlossen werden. Stromversorgung des Speichers Wenn die gelbe Stromversorgungsleitung angeschlossen ist, wird der Speicher stets (auch bei ausgeschalteter Zündung) mit Strom versorgt. Hinweise zum Lautsprecheranschluss • Schalten Sie das Gerät aus, bevor Sie die Lautsprecher anschließen. • Verwenden Sie Lautsprecher mit einer Impedanz zwischen 4 und 8 Ohm und ausreichender Belastbarkeit. Ansonsten können die Lautsprecher beschädigt werden. • Verbinden Sie die Lautsprecheranschlüsse nicht mit dem Wagenchassis und verbinden Sie auch nicht die Anschlüsse des rechten mit denen des linken Lautsprechers. • Verbinden Sie die Masseleitung dieses Geräts nicht mit dem negativen (–) Lautsprecheranschluss. • Versuchen Sie nicht, Lautsprecher parallel anzuschließen. • An die Lautsprecheranschlüsse dieses Geräts dürfen nur Passivlautsprecher angeschlossen werden. Schließen Sie keine Aktivlautsprecher (Lautsprecher mit eingebauten Verstärkern) an, da das Gerät sonst beschädigt werden könnte. • Um Fehlfunktionen zu vermeiden, verwenden Sie nicht die im Fahrzeug installierten, integrierten Lautsprecherleitungen, wenn eine gemeinsame negative (–) Leitung für den rechten und den linken Lautsprecher verwendet wird. • Verbinden Sie nicht die Lautsprecherkabel des Geräts miteinander. Hinweis zum Anschließen Wenn Lautsprecher und Verstärker nicht richtig angeschlossen sind, erscheint „Failure“ im Display. Vergewissern Sie sich in diesem Fall, dass Lautsprecher und Verstärker richtig angeschlossen sind. Cautions • This unit is designed for negative earth 12 V DC operation only. • Do not get the leads under a screw, or caught in moving parts (e.g. seat railing). • Before making connections, turn the car ignition off to avoid short circuits. • Connect the power connecting lead 6 to the unit and speakers before connecting it to the auxiliary power connector. • Run all earth leads to a common earth point. • Be sure to insulate any loose unconnected leads with electrical tape for safety. Notes on the power supply lead (yellow) • When connecting this unit in combination with other stereo components, the connected car circuit’s rating must be higher than the sum of each component’s fuse. • When no car circuits are rated high enough, connect the unit directly to the battery. Parts Iist (1) • The numbers in the list are keyed to those in the instructions. • The bracket 1 and the protection collar 4 are attached to the unit before shipping. Before mounting the unit, use the release keys 8 to remove the bracket 1 and the protection collar 4 from the unit. For details, see “Removing the protection collar and the bracket (5)” on the reverse side of the sheet. • Keep the release keys 8 for future use as they are also necessary if you remove the unit from your car. Caution Handle the bracket 1 carefully to avoid injuring your fingers. Note Before installing, make sure that the catches on both sides of the bracket 1 are bent inwards 2 mm. If the catches are straight or bent outwards, the unit will not be installed securely and may spring out. Connection example (2) Notes (2-A) • Be sure to connect the earth lead before connecting the amplifier. • If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be deactivated. Tip (2-B- ) For connecting two or more CD/MD changers, the source selector XA- C30 (optional) is necessary. Connection diagram (3) A To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit. B To the interface cable of a car telephone C To the parking brake switch cord Warning If you have a power aerial without a relay box, connecting this unit with the supplied power connecting lead 6 may damage the aerial. Notes on the control leads • The power aerial control lead (blue) supplies +12 V DC when you turn on the tuner, or when you activate the AF (Alternative Frequency) or TA (Traffic Announcement) function. • When your car has built-in FM/MW/LW aerial in the rear/side glass, connect the power aerial control lead (blue) or the accessory power input lead (red) to the power terminal of the existing aerial booster. For details, consult your dealer. • A power aerial without a relay box cannot be used with this unit. Memory hold connection When the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. Notes on speaker connection • Before connecting the speakers, turn the unit off. • Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. • Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker. • Do not connect the earth lead of this unit to the negative (–) terminal of the speaker. • Do not attempt to connect the speakers in parallel. • Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. • To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers. • Do not connect the unit’s speaker leads to each other. Note on connection If speaker and amplifier are not connected correctly, “Failure” appears in the display. In this case, make sure the speaker and amplifier are connected correctly. Installation/Connections Installation/Anschluss Installation/Connexions Installazione/Collegamenti Installatie/Aansluitingen FM/MW/LW Compact Disc Player CDX-M9900 © 2004 Sony Corporation Printed in Korea 3-265-746-21(1) Equipment used in illustrations (not supplied) In Abbildungen dargestellte Geräte (nicht mitgeliefert) Appareils utilisés dans les illustrations (non fournis) Apparecchiatura utilizzata nelle illustrazioni (non in dotazione) Apparatuur gebruikt voor illustratiedoeleinden (niet bijgeleverd) Rear speaker Hecklautsprecher Haut-parleur arrière Diffusore posteriore Achterluidspreker Front speaker Frontlautsprecher Haut-parleur avant Diffusore anteriore Voorluidspreker Yellow Gelb Jaune Giallo Geel Blue Blau Bleu Blu Blauw Orange/White Orangeweiß gestreift Rayé orange/ blanc Arancione/ bianco Oranje/wit continuous power supply permanente Stromversorgung alimentation continue alimentazione continua continu voeding power aerial control Motorantennensteuerung antenne électrique comando dell’antenna elettrica automatische antenne switched illumination power supply geschaltete Beleuchtungsstromversorgung alimentation de l’éclairage commuté alimentazione illuminazione commutata geschakelde verlichting stroomvoorziening 7 8 4 5 6 Red Rot Rouge Rosso Rood Black Schwarz Noir Nero Zwart switched power supply geschaltete Stromversorgung alimentation commutée alimentazione commutata geschakelde voeding earth Masse masse terra aarding 1 2 3 4 Speaker, Rear, Right Lautsprecher hinten rechts Haut-parleur, arrière, droit Diffusore, posteriore, destro Luidspreker, achter, rechts Speaker, Rear, Right Lautsprecher hinten rechts Haut-parleur, arrière, droit Diffusore, posteriore, destro Luidspreker, achter, rechts Speaker, Front, Right Lautsprecher vorne rechts Haut-parleur, avant, droit Diffusore, anteriore, destro Luidspreker, voor, rechts Speaker, Front, Right Lautsprecher vorne rechts Haut-parleur, avant, droit Diffusore, anteriore, destro Luidspreker, voor, rechts 5 6 7 8 Speaker, Front, Left Lautsprecher vorne links Haut-parleur, avant, gauche Diffusore, anteriore, sinistro Luidspreker, voor, links Speaker, Front, Left Lautsprecher vorne links Haut-parleur, avant, gauche Diffusore, anteriore, sinistro Luidspreker, voor, links Speaker, Rear, Left Lautsprecher hinten links Haut-parleur, arrière, gauche Diffusore, posteriore, sinistro Luidspreker, achter, links Speaker, Rear, Left Lautsprecher hinten links Haut-parleur, arrière, gauche Diffusore, posteriore, sinistro Luidspreker, achter, links Purple Violett Mauve Viola Paars White Weiß Blanc Bianco Wit Grey Grau Gris Grigio Grijs + – + – + – + – from the car’s speaker connector vom Lautsprecheranschluss des Fahrzeugs du connecteur de haut-parleur de la voiture dal connettore del diffusore dell’auto van de autoluidsprekerstekker from the car’s power connector vom Stromanschluss des Fahrzeugs du connecteur d’alimentation de la voiture dal connettore di alimentazione dell’auto van de autovoedingsstekker See “Power connection diagram” on the reverse side for details. Näheres dazu finden Sie im „Stromanschlussdiagramm“. Blättern Sie dazu bitte um. Voir le « Schéma de raccordement d’alimentation » au verso pour plus de détails. Per ulteriori informazioni, vedere “Diagramma dei collegamenti di alimentazione” che si trova sul retro. Zie "Voedingsaansluitschema" op de achterkant voor meer details. 3 1 Negative polarity positions 2, 4, 6, and 8 have striped leads. An den negativ gepolten Positionen 2, 4, 6 und 8 befinden sich gestreifte Adern. Les positions de polarité négative 2, 4, 6 et 8 sont dotées de cordons rayés. Le posizioni a polarità negativa 2, 4, 6 e 8 hanno cavi rigati. De posities voor negatieve polariteit (2, 4, 6 en 8) hebben gestreepte kabels. Green Grün Vert Verde Groen Power amplifier Endverstärker Amplificateur de puissance Amplificatore di potenza Eindversterker 1 Catch Active subwoofer Aktiv-Tiefsttonlautsprecher Caisson de graves actif Subwoofer attivo Actieve subwoofer DVD player DVX-11A DVD-Player DVX-11A Lecteur DVD DVX-11A Lettore DVD DVX-11A DVD-speler DVX-11A 1 Verriegelung 1 Loquet 1 Fermo 1 Greep 2 A B Source selector*2 Signalquellenwähler*2 Sélecteur de source*2 Selettore di fonte*2 Geluidsbronkiezer*2 XA-C30 CD/MD changer CD/MD-Wechsler Changeur de CD/MD Cambia CD/MD CD/MD-wisselaar Positions 1, 2 and 3 do not have pins. An Position 1, 2 und 3 befinden sich keine Stifte. Les positions 1, 2 et 3 ne comportent pas de broches. Le posizioni 1, 2 e 3 non hanno piedini. De posities 1, 2 en 3 hebben geen pinnen. VIDEO IN BUS CONTROL IN BUS AUDIO IN/AUX IN*1 *1 *1 *4 *8 *3 *2 *2 *7 *5 *1 Cordon à broche RCA (non fourni) *2 Appareil auxiliaire tel qu’un lecteur DVD portable (non fourni) *3 Fourni avec l’équipement auxiliaire *4 Veillez à faire correspondre le code de couleurs audio aux fiches correspondantes de l’appareil. Si vous raccordez un appareil CD ou MD en option, vous ne pouvez pas utiliser la borne AUX IN. *5 Fourni avec le XA-C30 *6 Fourni avec le changeur de CD/MD *7 Insérez avec le câble vers le haut *8 Veillez à faire correspondre le code de couleurs audio et vidéo aux prises correspondantes de l’appareil. *9 Les connecteurs BUS AUDIO IN et AUX IN se commutent automatiquement selon l’appareil raccordé. *10 Remarque sur le raccordement de l’antenne Si votre antenne de voiture est de type ISO (Organisation internationale de normalisation), utilisez l’adaptateur fourni 5 pour la raccorder. Raccordez d’abord l’antenne de voiture à l’adaptateur fourni et, ensuite, à la prise d’antenne de l’appareil principal. *11 Pour obtenir davantage d’informations sur le raccordement au cordon du capteur du frein à main et pour savoir comment installer la dérivation 7, reportez- vous à la section « Raccordement du cordon du capteur du frein à main (4) » au verso. *1 Cinchkabel (nicht mitgeliefert) *2 Zusätzliche Geräte wie z. B. der tragbare DVD-Player *3 Mit den Zusatzgeräten mitgeliefert *4 Achten Sie darauf, das farbcodierte Audiokabel mit den richtigen Buchsen am Gerät zu verbinden. Wenn ein gesondert erhältliches CD/MD-Gerät angeschlossen ist, kann der Anschluss AUX IN nicht verwendet werden. *5 Mit dem XA-C30 geliefert *6 Mit dem CD/MD-Wechsler geliefert *7 Mit dem Kabel nach oben einsetzen *8 Achten Sie darauf, die farbcodierten Audio-und Videokabel mit den richtigen Buchsen am Gerät zu verbinden. *9 BUS AUDIO IN und AUX IN werden je nach angeschlossenem Gerät automatisch gewechselt. *10 Hinweis zum Anschließen der Antenne Wenn Ihre Fahrzeugantenne der ISO-Norm (ISO = International Organization for Standardization - Internationale Normungsgemeinschaft) entspricht, schließen Sie sie mithilfe des mitgelieferten Adapters 5 an. Verbinden Sie zuerst die Fahrzeugantenne mit dem mitgelieferten Adapter und verbinden Sie diesen dann mit der Antennenbuchse des Hauptgeräts. *11 Informationen zum Anschließen der Parkbremsenschaltleitung und zum Anbringen des Kontaktstücks 7 finden Sie unter „Anschließen der Parkbremsenleitung (4)“ auf der Rückseite. *1 Cavo a piedini RCA (non in dotazione) *2 Apparecchio opzionale ausiliario quale un lettore DVD portatile *3 In dotazione con l’apparecchio ausiliario *4 Assicurarsi che i cavi differenziati in base al colore per l’audio corrispondano alle prese appropriate dell’apparecchio. Se viene collegato un apparecchio CD/ MD opzionale, non è possibile utilizzare il terminale AUX IN. *5 In dotazione con il modello XA-C30 *6 In dotazione con il cambia CD/MD *7 Inserire con il cavo rivolto verso l’alto *8 Assicurarsi che i cavi differenziati in base al colore per l’audio e per il video corrispondano alle prese appropriate dell’apparecchio. *9 BUS AUDIO IN o AUX IN viene automaticamente impostato in base all’apparecchio collegato. *10 Nota per il collegamento dell’antenna Se l’antenna dell’auto è di tipo ISO (International Organization for Standardization), utilizzare l’adattatore 5 in dotazione per collegarla. Collegare prima l’antenna della macchina all’adattatore in dotazione, quindi collegarla alla presa dell’antenna dell’apparecchio principale. *11 Per ulteriori informazioni sul collegamento al cavo di commutazione del freno a mano e sull’applicazione del dispositivo di accoppiamento 7, consultare “Collegamento del cavo del freno a mano (4)” sul lato opposto. *1 Tulpstekkersnoer (niet bijgeleverd) *2 Optionele apparatuur zoals de draagbare DVD-speler (niet bijgeleverd) *3 Geleverd bij de optionele apparatuur *4 Zorg ervoor dat de kleurcode voor audio overeenkomt met de betreffende aansluitingen op het apparaat. Als u optionele CD/MD- apparatuur aansluit, kunt u de AUX IN aansluiting niet gebruiken. *5 Geleverd bij de XA-C30 *6 Geleverd bij de CD/MD-wisselaar *7 Plaatsen met het snoer naar boven *8 Zorg dat de kleurcode van de kabel voor audio en beeld overeenkomt met de betreffende aansluitingen op het apparaat. *9 BUS AUDIO IN en AUX IN worden automatisch geschakeld, afhankelijk van de aangesloten apparatuur. *10 Opmerking bij de antenne- aansluiting Indien uw auto is uitgerust met een antenne van het type ISO (International Organisation for Standardization), moet u die aansluiten met de bijgeleverde adapter 5. Sluit eerst de auto-antenne aan op de bijgeleverde adapter en vervolgens de antennestekker op het hoofdtoestel. *11 Zie "Parkeerremkabel aansluiten (4)" aan de achterzijde voor meer informatie over het aansluiten op het schakelsnoer van de parkeerrem en het bevestigen van het verbindingselement 7. Light green Hellgrün Vert clair Verde chiaro Lichtgroen Rotary commander RM-X4S Joystick RM-X4S Satellite de commande RM-X4S Telecomando a rotazione RM-X4S Bedieningssatelliet RM-X4S *6 3 2 5 4 1 × 2 6 7 8 9 7*11 *1 Use the AUX-IN selector XA-300 (not supplied) when you want to connect the audio outputs of a DVD player to the BUS AUDIO IN/ AUX IN terminal. *2 not supplied *1 Verwenden Sie den AUX-IN- Signalquellenwähler XA-300 (nicht mitgeliefert), wenn Sie die Audioausgänge eines DVD-Players mit dem Anschluss BUS AUDIO IN/AUX IN verbinden möchten. *2 nicht mitgeliefert *1 Utilisez le sélecteur AUX-IN XA-300 (non fourni) lorsque vous souhaitez raccorder les sorties audio d’un lecteur DVD à la borne BUS AUDIO IN/AUX IN. *2 non fourni *1 Se si desidera collegare le uscite audio di un lettore DVD al terminale BUS AUDIO IN/AUX IN, utilizzare il selettore AUX-IN XA-300 (non in dotazione). *2 non in dotazione *1 Gebruik de AUX-IN keuzeschakelaar XA-300 (niet bijgeleverd) als u de audio- uitgangen van een DVD- speler wilt aansluiten op de BUS AUDIO IN/AUX IN aansluiting. *2 niet bijgeleverd

1 Ver 1.0 2004. 02 Model Name Using Similar Mechanism CDX-F5500/F5500X/FW570 CD Drive Mechanism Type MG-611MA-186//K Optical Pick-up Name KSS1000E SERVICE MANUAL US Model Canadian Model CDX-M9900/M9905X AEP Model UK Model E Model CDX-M9900 CDX-M9900/M9905X AUDIO POWER SPECIFICATIONS (US Model) POWER OUTPUT AND TOTAL HARMONIC DISTORTION 23.2 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 5% total harmonic distortion. CD player section Signal-to-noise ratio 120 dB Frequency response 10 – 20,000 Hz Wow and flutter Below measurable limit Tuner section FM Tuning range 87.5 – 107.9 MHz (US, Canadian Model) 87.5 – 108.0 MHz (AEP, UK, E Model) Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Usable sensitivity 9 dBf Selectivity 75 dB at 400 kHz Signal-to-noise ratio 67 dB (stereo), 69 dB (mono) Harmonic distortion at 1 kHz 0.5% (stereo), 0.3% (mono) Separation 35 dB at 1 kHz Frequency response 30 – 15,000 Hz AM (US, Canadian Model) Tuning range 530 – 1,710 kHz Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity 30 µV SPECIFICATIONS MW/LW (AEP, UK, E Model) Tuning range MW : 531 – 1,602 kHz LW : 153 – 279 kHz Aerial terminal External aerial connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity MW : 30 µV LW : 40 µV Power amplifier section Outputs Speaker outputs (sure seal connectors) Speaker impedance 4 – 8 ohms Maximum power output 52 W × 4 (at 4 ohms) General Outputs Audio outputs (front/rear) Subwoofer output (mono) Power antenna relay control terminal Power amplifier control terminal Inputs Telephone ATT control terminal Illumination control terminal Parking brake input terminal (US, Canadian, AEP, UK Model) BUS control input terminal BUS audio input/AUX IN terminal Antenna input terminal Video input terminal • The tuner and CD sections have no adjustments. Sony Corporation e Vehicle Company Published by Sony Engineering Corporation 9-877-633-01 2004B04-1 © 2004. 02 – Continued on next page – FM/AM COMPACT DISC PLAYER US, Canadian Model FM/MW/LW COMPACT DISC PLAYER AEP, UK, E Model Photo: CDX-M9900

Operating Instructions © 2004 Sony Corporation 3-265-745-31 (1) CDX-M9900 For installation and connections, see the supplied installation/connections manual. CT GB FM/MW/LW Compact Disc Player

Operating Instructions XM Satellite Radio Receiver XT-XM1 Sony Corporation © 2002 Printed in Japan Owner’s Record The model number is located on the bottom and serial number also on the bottom. Record the serial number in the space provide below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. XT-XM1 Serial No. XM Radio ID You need to subscribe for XMTM Satellite Radio Service to listen to the radio broadcast. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. 3-243-168-11 (1) If you have any questions or problem concerning this product, consult your nearest Sony dealer. If you have any questions or problem concerning the XM Satellite radio service including the broadcast, consult XM. The XM Radio ID (XM-ID) is required when consulting XM. It is located on the bottom of the main unit, and you can also check it in the display of this unit (see “Displaying the XM Radio ID”). Welcome! Thank you for purchasing the Sony XM Satellite Radio Receiver. The receiver allows you to: •Receive XM Satellite Radio programming (with subscription) by connecting a Sony master unit* compatible with the Sony BUS system. •Connect and use an optional CD or MD changer. •Receive up to 100 channels of XM programming. •Display channel name, artist name, and song title for most XM channels. •Store up to 20 favorite XM channels. •Search XM channels by category. * Some master units may not be connected to this receiver. (For details, please consult your nearest Sony dealer.) Introducing XMTM Satellite Radio There’s a world beyond AM and FM. XM Satellite Radio. Up to 100 channels. Coast-to- Coast Coverage. Digital quality sound. With many commercial-free music channels. Plus, the best sports, comedy, talk, news and entertainment, including USA Today, Discovery Radio, NASCAR, Sesame Workshop, CNNfn and CNN/SI. Questions? Visit www.xmradio.com. The future is waiting. How to Subscribe Listeners can subscribe by visiting XM on the Web at www.xmradio.com or by calling XM’s Listener Care at (800)852-9696. Customers should have their Radio ID ready; it is located on the bottom of the main unit, and you can also check it in the display of this unit (see “Displaying the XM Radio ID”). Technology. It is prohibited to copy, decompile, disassemble, reverse engineer or manipulate any technology incorporated in receivers compatible with the XM Satellite Radio system. Furthermore, the AMBE® voice compression software included in this product is protected by intellectual property rights including patent rights, copyrights, and trade secrets of Digital Voice Systems, Inc. The user of this or any other software contained in an XM Radio is explicitly prohibited from attempting to copy, decompile, reverse engineer, or disassemble the object code, or in any other way convert the object code into human-readableform. The software is licensed solely for use within this product. Getting Started Resetting the master unit Before operating the XM receiver for the first time, reset the master unit. If the unit is not reset in this manner, it may not function properly. For details on how to reset it, refer to the operating instructions of the master unit. Caution For the following master units, press the Repeat (REP) button of the master unit for two seconds after turning the XM on and select “setup 2.” Without this procedure, the master unit will not display tuning-in information from the receiver correctly. Except for the following master units, “setup 1” is selected in the factory settings. CDX-C8050X CDX-C800REC* CDX-M750 CDX-M650 CDX-M610 CDX-M600 MDX-C8500X XR-M550 * You may observe flickering in parts of the display while performing operations. This is not malfunction. Note Resetting the master unit will erase the clock setting and some stored contents of the master unit. Using category search to locate channels Each XM channel is associated with a category that describes the type of music or programming that is played on the channel. Examples of categories include “rock,” “jazz,” “news,” and so on. Users unfamiliar with XM’s programming may use the radio’s search-by-category function to select channels. 1 Press the Repeat (REP) button to enter category search mode. The category of the current channel is displayed. With some master units, the Repeat button is only equipped on the remote control. 2 Press the Disc/Preset buttons repeatedly until you find the desired category. 3 Press the Seek buttons repeatedly until you find the desired channel in that category. The display shows “CAT SRCH” to indicate that the radio is in category search mode. While in this mode, you will only be able to tune to channels in the selected category. You may use the Disc/Preset buttons to choose other categories. 4 To exit from category search mode and return to the normal mode, press the Repeat (REP) button. The radio automatically returns to the normal mode if there no key is pressed within 5 seconds. Storing favorite channels You can preset up to 20 channels. 1 Tune in a channel that you want to store. 2 Press the Shuffle (SHUF) button. The radio will show a list of presets, starting with preset number 1. The preset number will be shown if a channel has already been stored into the preset. With some master units, the Shuffle button is only equipped on the remote control. 3 Press the Disc/Preset button to select a preset number. With some master units, the Disc/Preset button is only equipped on the remote control. 4 Press the Disc/Preset + (Disc +) button for 2 seconds. The display shows “MEMORY” if the radio successfully stores the channel into the preset. The display shows “FAILURE” if the radio fails to store the channel into the preset. The radio automatically returns to the normal mode if there no key is pressed within 5 seconds. Receiving a stored channel • Press either Disc/Preset button to select the preset channel you want to listen to. • Press the Shuffle (SHUF) button. Press the Disc/Preset + (DISC +) button to select the preset channel and then press the SEEK + or SEEK – button to start. Displaying the XM Radio ID 1 During XM Satellite Radio reception, press the Seek button to select “CHANNEL 1.” 2 Press the “Seek – (down)” button. “RADIO ID” is indicated for 2 seconds and the XM Radio ID number is indicated for 10 seconds. These indications will be displayed alternately. To cancel the XM Radio ID display, press the Seek button to select a channel. Basic Operations Listening to a program The XM receiver is controlled by the master unit. Button locations vary with different master unit models. Please refer to the master unit instruction manuals. 1 To select XM: a. Press the Source button until “XM” is displayed. -or- b. Press the Source button until “MD” is displayed, then press the Mode button to select XM. For master units which can control more than one MD changer, press the Mode button repeatedly (the display will show “MD1,” “MD2,” etc.) until the receiver is found. 2 Press either Seek button to select the desired channel. Pressing and holding the Seek button will quickly step through the channels. Note “LOADING” is indicated while the receiver is reading the information. Display items The XM Satellite Radio information (Channel Name, Channel Number, Artist Name/Program Name and Song Title) is available on the display. Press the Display (DSPL) button. Each time you press the Display (DSPL) button, the item changes as follows: Channel Name t Channel Number t Artist Name/Program Name t Song Title t For MEX-5DI, press the ENTER button of the remote control to change the display item. Notes • While Artist Name/Program Name or Song Title is displayed, if you select a channel, Channel Name will be displayed for 2 to 3 seconds and then return to the previous display. • If there is no information about Artist Name/ Program Name or Song Title, “- - - -” will be displayed. • During XM Satellite Radio reception, Spectrum Analyzer, Dual Information, Motion Display function of the master unit cannot be operated. • The display indicates up to 8 characters. The characters on the display cannot be scrolled even when the Auto Scroll function of the master unit is set to on. • You cannot display the clock during XM Satellite Radio reception on a master unit whose clock display is shown by pressing the Display (DSPL) button. Additional Information Specifications Frequency 2332.5 – 2345.0 MHz Power requirements 12 V DC car battery (negative ground) Outputs BUS control output Audio output Inputs Antenna input (Satellite, Terrestrial) BUS control input Audio input Dimensions 224 × 37.8 × 160 mm (8 7/8 × 1 1/2 × 6 3/8 in.) (w/h/d) Mass Approx. 1.0 kg (2 lb. 4 oz.) Supplied accessories Parts for installation and connection (1 set) Design and specifications are subject to change without notice. Troubleshooting Should any problem persist after you have made the following checks, consult your nearest Sony dealer. Consult XM if you have any questions or problem concerning the broadcast service of the XM Satellite radio. The information on the display cannot be changed during XM Satellite Radio reception. •Refer to “Caution” in “Getting Started.” No sound. •Adjust the volume control of the master unit. •Cancel the attenuate function of the master unit. •The connecting cords are not connected properly. The sound is hampered by noises. Locate codes and cables such as an antenna code, a BUS cable, an RCA pin code, or a power code so as they do not interfere each other. The channels cannot be received. Check the connection of the receiver and the antenna. Advisory Message When a problem occurs with the receiver, an error message will be indicated on the display of the master unit. ANTENNA The antenna is not connected properly. t Check the connection of the receiver and the antenna. UPDATING You have not subscribed to XM, or the channel is not authorized. t You need to subscribe to XM. NO SIGNL XM signal is too weak. t Move to another area where your system can receive the signal. OFF AIR The channel is not broadcasted now. t Select another channel. LOADING The receiver is reading the channel information t Wait until the receiver completes receiving the information. “– – – –” or “CH – – –” •The channel to be tuned-in is void due to the change by the broadcast service, or the receiving condition is not good. •There is no text information or time information in the channel. This is not an error.