Sony CFD-S22L Manuals

Specifications CD player section System Compact disc digital audio system Laser diode properties Material: GaAlAs Wave length: 780 nm Emission duration: Continuous Laser output: Less than 44.6 µW (This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.) Spindle speed 200 r/min (rpm) to 500 r/min (rpm) (CLV) Number of channels 2 Frequency response 20 - 20,000 Hz +1/–2 dB Wow and flutter Below measurable limit Radio section Frequency range CFD-S22/S32 FM 87.5 - 108 MHz or 87.6 - 108 MHz AM 531 - 1,602 kHz CFD-S22L/S32L/922L FM 87.5 - 108 MHz MW 531 - 1,602 kHz LW 153 - 279 kHz IF FM: 10.7 MHz AM/MW/LW: 450 kHz Aerials FM: Telescopic aerial AM/MW/LW: Built-in ferrite bar aerial Cassette-corder section Recording system 4-track 2 channel stereo Fast winding time Approx. 120 s (sec.) with Sony cassette C-60 Frequency response TYPE I (normal): 70 - 10,000 Hz General Speaker Full range: 10 cm dia., 3.2 ohms, cone type (2) Outputs Headphones jack (stereo minijack) For 16 - 68 ohms impedance headphones Maximum power output 2.3 W + 2.3 W Power requirements For CD radio cassette-corder: Brazilian model: 110 - 120V, 220 - 240V AC selectable, 50/60 Hz Other models: 230 V AC, 50 Hz 9 V DC, 6 R20 (size D) batteries For remote control (CFD-S32/S32L only): 3 V DC, 2 R6 (size AA) batteries Power consumption AC 20 W Battery life For CD radio cassette-corder: FM recording Sony R20P: approx. 13.5 h Sony alkaline LR20: approx. 20 h Tape playback Sony R20P: approx. 7.5 h Sony alkaline LR20: approx. 15 h CD playback Sony R20P: approx. 2.5 h Sony alkaline LR20: approx. 7 h Tape Player The tape does not move when you press an operation button. • Close the cassette compartment securely. The REC z button does not function or the tape does not play or record. • Make sure the safety tab on the cassette is in place. • Make sure "TAPE" appears in the display. Poor or distorted playback, recording or erasing quality. • Clean the heads, pinch roller and capstan with a cleaning swab slightly moistened with cleaning fluid or alcohol. • Replace all the batteries with new ones if they are weak. • TYPE II (high position) or TYPE IV (metal) tape is being used. Use TYPE I (normal) tape only. • Demagnetize the heads using a commercially available tape head demagnetizer. Remote (CFD-S32/S32L only) The remote does not function. • Replace all the batteries in the remote with new ones if they are weak. • Make sure that you are pointing the remote at the remote sensor on the player. • Remove any obstacles in the path of the remote and the player. • Make sure the remote sensor is not exposed to strong light such as direct sunlight or fluorescent lamp light. • Move closer to the player when using the remote. After trying the above remedies, if you still have problems, unplug the mains lead and remove all the batteries. After all the indications in the display disappear, plug the power cord and insert the batteries again. If the problem persists, please consult your nearest Sony dealer. Sony Corporation © 2000 Operating Instructions CD Radio Cassette- Corder 3-043-356-31(1) CFD-S22 CFD-S22L CFD-S32 CFD-S32L CFD-922L 1 Press TAPE (direct power-on). 2 Press xZ to open the tape compartment and insert a recorded tape. Close the compartment. 3 Press N. With the side you want to play facing upward 2 Select the program source you want to record. To record from the CD player Press CD and insert a CD (See "Playing a CD"). To record from the radio Press RADIO BAND•AUTO PRESET and tune in the station you want (See "Listening to the radio"). 3 Press z to start recording. (N is depressed automatically.) 1 Press xZ to open the tape compartment and insert a blank tape. With the side you want to record on facing upward To Press stop recording xZ pause recording X Press the button again to resume recording. turn on/off the player OPERATE (or POWER) Tips • Adjusting the volume or the audio emphasis will not affect the recording level. • CFD-S22L/S32L/922L only: If the MW/LW program makes a whistling sound after you've pressed z in step 3, press PLAY MODE• MONO/ST ISS (Interference Suppress Switch) repeatedly until the noise is at a minimum. • For the best results, use the AC power as a power source for recording. • To erase a recording, proceed as follows: 1 Insert a tape with the recording you want to erase. 2 Press TAPE. 3 Press z. To adjust the volume stop playback fast-forward or rewind the tape pause playback eject the cassette turn on/off the player Notes on cassettes • Break off the cassette tab from side A or B to prevent accidental recording. If you want to reuse the tape for recording, cover the broken tab with adhesive tape. • The use of a cassette with more than 90 minutes of play time is not recommended except for long, continuous recording or playback. Tab for side B Tab for side A Side A c c Use TYPE I (normal) tape only. Press VOLUME +, – (VOL +, – on the remote, CFD-S32/S32L only) xZ M or m X Press the button again to resume play after pause. xZ OPERATE (or POWER) Troubleshooting General The power does not come on. • Connect the mains lead securely. • Make sure the batteries are inserted correctly. • Replace all the batteries with new ones if they are weak. • You cannot turn on the player with the remote when you operate the player on batteries (CFD-S32/ S32L only). The power is not on, and "bAttErY" and "Error" are displayed alternately. • Make sure the batteries are inserted correctly. • Replace all the batteries with new ones if they are weak. There is no audio. • Make sure the function you want to use appears in the display. • Adjust the volume. • Unplug the headphones when listening through speakers. Noise is heard. • Someone is using a portable telephone or other equipment that emits radio waves near the player. tMove the portable telephone, etc., away from the player. CD Player The CD does not play or “no dISC” lights in the display even when a CD is in place. • Make sure that the CD compartment is closed. • Place the CD with the label surface up. • Clean the CD. • Take out the CD and leave the CD compartment open for about an hour to dry moisture condensation. • Make sure "Cd" appears in the display. The sound drops out. • Reduce the volume. • Clean the CD, or replace it if the CD is badly damaged. • Place the player in a location free from vibration. • Clean the lens with a commercially available blower. • The sound may drop out or noise may be heard if the CD is recorded using a personal computer(CD-R,etc.). Radio The audio is weak or has poor quality. • Replace all the batteries with new ones if they are weak. • Move the player away from the TV. The picture of your TV becomes unstable. • If you are listening to an FM program near the TV with an indoor antenna, move the player away from the TV. Using the player on batteries Insert six R20 (size D) batteries (not supplied) into the battery compartment. Notes • Replace the batteries when the OPR/BATT indicator dims or when the player stops operating. Replace all the batteries with new ones. Before you replace the batteries, be sure to take out the CD from the player. • To use the player on batteries, disconnect the mains lead from the player. Inserting batteries into the remote (CFD-S32/S32L only) Insert two R6 (size AA) batteries (not supplied) Replacing batteries With normal use, the batteries should last for about six months. When the remote no longer operates the player, replace all the batteries with new ones. Note When you operate the player on batteries, you cannot turn on the player using the remote. Connecting the mains lead Insert one end of the supplied mains lead to the AC IN socket located at the rear of the player, and the other end to the mains. 1 to AC IN 2 to the mains Choosing Power Sources To cancel the sleep function Press OPERATE (or POWER) to turn off the power. Note When you are playing a tape using this function: If the tape length of one side is longer than the set time, the player will not go off until the tape reaches the end. Falling asleep to music 2 Press SLEEP to display “SLEEP.” 3 Press SLEEP to select the minutes until the player goes off automatically. Each time you press the button, the indication changes as follows: “60” n “90” n “120” n no indication n “10” n “20” n “30.” 1 Play the music source you want. Precautions On safety • As the laser beam used in the CD player section is harmful to the eyes, do not attempt to disassemble the casing. Refer servicing to qualified personnel only. • Should any solid object or liquid fall into the player, unplug the player, and have it checked by qualified personnel before operating it any further. Cleaning the cabinet • Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzine. On power sources • For AC operation, check that the player's operating voltage is identical with your local power supply (see "Specifications") and use the supplied mains lead; do not use any other type. The voltage selector is located at the bottom of the player (for Brazilian model only). • The player is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the player itself has been turned off. • For battery operation, use six R20 (size D) batteries. • When the batteries are not to be used, remove them to avoid damage that can be caused by battery leakage or corrosion. • The nameplate indicating operating voltage, power consumption, etc. is located at the bottom. On placement • Do not leave the player in a location near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock. • Do not place the player on an inclined or unstable place. • Do not place anything within 10 mm of the side of the cabinet. The ventilation holes must be unobstructed for the player to operate properly and prolong the life of its components. • If the player is left in a car parked in the sun, be sure to choose a location in the car where the player will not be subjected to the direct rays of the sun. • Since a strong magnet is used for the speakers, keep personal credit cards using magnetic coding or spring-wound watches away from the player to prevent possible damage from the magnet. On operation • If the player is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lenses inside the CD player section. Should this occur, the player will not operate properly. In this case, remove the CD and wait about an hour for the moisture to evaporate. • If the player has not been used for a long time, set it in the playback mode to warm it up for a few minutes before inserting a cassette. If you have any questions or problems concerning your player, please consult your nearest Sony dealer. Erase head Pinch roller Record/playback head Capstan Lens Display Display Display English Display WARNING To prevent fire or shock hazard, do not expose the player to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Information For customers in Europe This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the bottom exterior. WARNING Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. Notice for customers in the United Kingdom A moulded plug complying with BS 1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced, same rating fuse approved by ASTA or BSI to BS 1362, (i.e. marked with or mark) must be used. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station. About this manual The instructions in this manual are for the CFD-S22, CFD-S22L, CFD- S32, CFD-S32L and CFD-922L. Before you start reading, check your model number. The CFD-S32L is the model used for illustration purposes. Note The name of the switch to turn on/ off this player is indicated as below: “OPERATE”: CFD-S22L/S32L/ 922L “POWER”: CFD-S22/S32 Brazilian model only: Adjusting the voltage Be sure to set the VOLTAGE SELECTOR (at the bottom) to your local power supply. Tip Only for the customers supplied with an AC plug adaptor: Use the supplied AC plug adaptor if the plug of the main lead does not match your outlet. Dimensions Approx. 420 × 165 × 256 mm (w/h/d) (16 5⁄8 × 6 1⁄2 × 10 1⁄8 inches) (incl. projecting parts) Mass Approx. 4.1 kg (9 lb. 1 oz) (incl. batteries) Supplied accessory Mains lead (1) Remote control (1) (CFD-S32/S32L only) Design and specifications are subject to change without notice. Optional accessories Sony MDR headphone series Use TYPE I (normal) tape only. Playing a tape Recording

– 1 – CD Model Name Using Similar Mechanism CFD-S38L Section CD Mechanism Type KSM-213CDM Optical Pick-up Name KSS-213C TC Model Name Using Similar Mechanism CFD-S38L Section Tape Transport Mechanism Type MF-S22-117 SERVICE MANUAL AEP Model UK Model CFD-S22L/S32L CD RADIO CASSETTE-CORDER CD player section System Compact disc digital audio system Laser diode properties Material: GaAlAs Wave length: 780 nm Emission duration: Continuous Laser output: Less than 44.6 µW (This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.) Spindle speed 200 r/min (rpm) to 500 r/min (rpm) (CLV) Number of channels 2 Frequency response 20 - 20,000 Hz +1/–2 dB Wow and flutter Below measurable limit Radio section Frequency range CFD-S22L/S32L FM 87.5 - 108 MHz MW 531 - 1,602 kHz LW 531 - 279 kHz IF FM: 10.7 MHz MW/LW: 450 kHz Aerials FM: Telescopic aerial MW/LW: Built-in ferrite bar aerial SPECIFICATIONS – Continued on next page – Cassette-corder section Recording system 4-track 2 channel stereo Fast winding time Approx. 120 sec. with Sony cassette C-60 Frequency response TYPE I (normal): 70 - 10,000 Hz General Speaker Full range: 10 cm (4 in.) dia., 3.2 ohms, cone type (2) Outputs Headphones jack (stereo minijack) For 16 - 68 ohms impedance headphones Maximum power output 2.3 W + 2.3 W Power requirements For CD radio cassette-corder: 230 V AC, 50 Hz 9 V DC, 6 R20 (size D) batteries For remote control (CFD-S32L only): 3 V DC, 2 R6 (size AA) batteries Power consumption AC 20 W Photo: CFD-S32L Ver 1.0 2000. 03 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com http://www.xiaoyu163.com