Sony CFD-S26 - Cd Radio Cassette-corder Manuals

Specifications AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION With 3.2-ohm loads, both channels driven from 150 - 6,300 Hz; rated 1.8 W per channel-minimum RMS power, with no more than 10 % total harmonic distortion in AC operation. Other Specifications CD player section System Compact disc digital audio system Laser diode properties Material: GaAlAs Wave length: 780 nm Emission duration: Continuous Laser output: Less than 44.6 µW (This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.) Spindle speed 200 r/min (rpm) to 500 r/min (rpm) (CLV) Number of channels 2 Frequency response 20 - 20,000 Hz +1/–2 dB Wow and flutter Below measurable limit Radio section Frequency range FM: 87.6 - 108 MHz AM: 530 - 1,710 kHz TV: 2 - 13 CH (CFD-S36 USA model only) WEATHER: 1 - 7 CH (CFD-S36 USA model only) Antennas FM/TV/WEATHER: Telescopic antenna AM: Built-in ferrite bar antenna Cassette-corder section Recording system 4-track 2 channel stereo Fast winding time Approx. 120 s (sec.) with Sony cassette C-60 Frequency response TYPE I (normal): 80 - 10,000 Hz General Speaker Full range: 10 cm dia., 3.2 ohms, cone type (2) Outputs Headphones jack (stereo minijack) For 16 - 68 ohms impedance headphones Power output (excluding USA model) 2.3 W + 2.3 W (at 3.2 ohms, 10 % harmonic distortion in AC operation) Power requirements For CD radio cassette-corder: 120 V AC, 60 Hz 9 V DC, 6 size D (R20) batteries For remote control (CFD-S36 only): 3 V DC, 2 size AA (R6) batteries Power consumption AC 20 W Battery life For CD radio cassette-corder: FM recording Sony R20P: approx. 13.5 h Sony alkaline LR20: approx. 20 h Tape playback Sony R20P: approx. 7.5 h Sony alkaline LR20: approx. 15 h CD playback Sony R20P: approx. 2.5 h Sony alkaline LR20: approx. 7 h Dimensions Approx. 420 × 159 × 284 mm (w/h/d) (16 5⁄8 × 6 3⁄8 × 11 1⁄4 inches) (incl. projecting parts) Mass Approx. 3.8 kg (8 lb. 6 oz) (incl. batteries) Tape Player The tape does not move when you press an operation button. • Close the cassette compartment securely. The REC z button does not function or the tape does not play or record. • Make sure the safety tab on the cassette is in place. Poor or distorted playback, recording or erasing quality. • Clean the heads, pinch roller and capstan with a cleaning swab slightly moistened with cleaning fluid or alcohol. • Replace all the batteries with new ones if they are weak. • TYPE II (high position) or TYPE IV (metal) tape is being used. Use TYPE I (normal) tape only. • Demagnetize the heads using a commercially available tape head demagnetizer. Remote (CFD-S36 only) The remote does not function. • Replace all the batteries in the remote with new ones if they are weak. • Make sure that you are pointing the remote at the remote sensor on the player. • Remove any obstacles in the path of the remote and the player. • Make sure the remote sensor is not exposed to strong light such as direct sunlight or fluorescent lamp light. • Move closer to the player when using the remote. After trying the above remedies, if you still have problems, unplug the AC power cord and remove all the batteries. After all the indications in the display disappear, plug the power cord and insert the batteries again. If the problem persists, please consult your nearest Sony dealer. Sony Corporation © 2000 Printed in China Operating Instructions CD Radio Cassette- Corder 3-227-155-14(1) WARNING To prevent fire or shock hazard, do not expose the player to rain or moisture. This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION The use of optical instruments with this product will increase eye hazard. WARNING Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. For customers in Canada To prevent electric shock, match wide blade of plug to wide slot, fully insert. Information For customers in the United States This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. If you have any questions about this product, you may call: Sony Direct Response Center 1-(800)-222-7669 CFD-S26 CFD-S36 1 Press TAPE (direct power-on). 2 Press xZ to open the tape compartment and insert a recorded tape. Close the compartment. 3 Press N. With the side you want to play facing upward 2 Select the program source you want to record. To record from the CD player Press CD and insert a CD (See "Playing a CD"). To record from the radio Press RADIO BAND•AUTO PRESET and tune in the station you want (See "Listening to the radio"). 3 Press z to start recording. (N is depressed automatically). 1 Press xZ to open the tape compartment and insert a blank tape. With the side you want to record on facing upward To stop recording pause recording turn on/off the player POWER Tips • Adjusting the volume or the audio emphasis will not affect the recording level. • For the best results, use the AC power as a power source for recording. • To erase a recording, proceed as follows: 1 Insert a tape with the recording you want to erase. 2 Press TAPE. 3 Press z. To adjust the volume stop playback fast-forward or rewind the tape pause playback eject the cassette turn on/off the player Notes on cassettes • Break off the cassette tab from side A or B to prevent accidental recording. If you want to reuse the tape for recording, cover the broken tab with adhesive tape. • The use of a cassette with more than 90 minutes of play time is not recommended except for long, continuous recording or playback. Tab for side B Tab for side A Side A c c Recording Playing a tape Press VOLUME +, – (VOL +, – on the remote, CFD-S36 only) xZ M or m X Press the button again to resume play after pause. xZ POWER Press xZ X Press the button again to resume recording. or write to: Sony Direct Response Center 12451 Gateway Blvd. Fort Myers, FL 33913 For CFD-S36 USA model only Declaration of Conformity Trade Name: SONY Model: CFD-S36 Responsible Party: Sony Electronics Inc. Address: 1 Sony Drive, Park Ridge, NJ 07656 U.S.A. Telephone Number: 201-930-6972 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Owner's Record The model number is located at the bottom and the serial number is located in the battery compartment. Record these numbers in the spaces provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. Serial No. About this manual The instructions in this manual are for the CFD-S26 and CFD-S36. Before you start reading, check your model number. The CFD-S36 is the model used for illustration purpose. Troubleshooting General The power does not come on. • Make sure the batteries are inserted correctly. • Replace all the batteries with new ones if they are weak. • You cannot turn on the player with the remote when you operate the player on batteries (CFD-S36 only). The power is not on, and "bAttErY" and "Error" are displayed alternately. • Make sure the batteries are inserted correctly. • Replace all the batteries with new ones if they are weak. There is no audio. • Unplug the headphones when listening through speakers. Noise is heard. • Someone is using a portable telephone or other equipment that emits radio waves near the player. tMove the portable telephone, etc., away from the player. CD Player The CD does not play or “no dISC” lights in the display even when a CD is in place. • Place the CD with the label surface up. • Clean the CD. • Take out the CD and leave the CD compartment open for about an hour to dry moisture condensation. • The CD-R/CD-RW was not finalized. Finalize the CD-R/CD- RW with the recording device. • There is a problem with the quality of the CD-R/CD-RW, recording device, or application software. The sound drops out. • Reduce the volume. • Clean the CD, or replace it if the CD is badly damaged. • Place the player in a location free from vibration. • Clean the lens with a commercially available blower. • The sound may drop out or noise may be heard when using poor quality CD-Rs/CD-RWs or if there is a problem with the recording device or application software. Radio The audio is weak or has poor quality. • Replace all the batteries with new ones if they are weak. • Move the player away from the TV. The picture of your TV becomes unstable. • If you are listening to an FM program near the TV with an indoor antenna, move the player away from the TV. Using the player on batteries Insert six size D (R20) batteries (not supplied) into the battery compartment. Notes • Replace the batteries when the OPR/BATT indicator dims or when the player stops operating. Replace all the batteries with new ones. Before you replace the batteries, be sure to take out the CD from the player. • To use the player on batteries, disconnect the AC power cord from the player. Connecting the AC power cord Insert one end of the supplied AC power cord to the AC IN socket located at the rear of the player, and the other end to the wall outlet. 1 to AC IN 2 to a wall outlet Choosing Power Sources To cancel the sleep function Press POWER to turn off the power. Note When you are playing a tape using this function: If the tape length of one side is longer than the set time, the player will not go off until the tape reaches the end. Falling asleep to music 2 Press SLEEP to display “SLEEP.” 3 Press SLEEP to select the minutes until the player goes off automatically. Each time you press the button, the indication changes as follows: “60” t “90” t “120” t no indication t “10” t “20” t “30.” 1 Play the music source you want. Precautions On safety • As the laser beam used in the CD player section is harmful to the eyes, do not attempt to disassemble the casing. Refer servicing to qualified personnel only. • Should any solid object or liquid fall into the player, unplug the player, and have it checked by qualified personnel before operating it any further. Cleaning the cabinet • Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzine. On power sources • For AC operation, use the supplied AC power cord; do not use any other type. • The player is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the player itself has been turned off. • Unplug the player from the wall outlet when it is not to be used for an extended period of time. • For battery operation, use six size D (R20) batteries. • When the batteries are not to be used, remove them to avoid damage that can be caused by battery leakage or corrosion. • The nameplate indicating operating voltage, power consumption, etc. is located at the bottom. On placement • Do not leave the player in a location near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock. • Do not place the player on an inclined or unstable place. • Do not place anything within 10 mm of the side of the cabinet. The ventilation holes must be unobstructed for the player to operate properly and prolong the life of its components. • If the player is left in a car parked in the sun, be sure to choose a location in the car where the player will not be subjected to the direct rays of the sun. • Since a strong magnet is used for the speakers, keep personal credit cards using magnetic coding or spring-wound watches away from the player to prevent possible damage from the magnet. On operation • If the player is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lenses inside the CD player section. Should this occur, the player will not operate properly. In this case, remove the CD and wait about an hour for the moisture to evaporate. • If the player has not been used for a long time, set it in the playback mode to warm it up for a few minutes before inserting a cassette. If you have any questions or problems concerning your player, please consult your nearest Sony dealer. Inserting batteries into the remote (CFD-S36 only) Insert two size AA (R6) batteries (not supplied) Replacing batteries With normal use, the batteries should last for about six months. When the remote no longer operates the player, replace all the batteries with new ones. Note When you operate the player on batteries, you cannot turn on the player using the remote. Display Display Display English Display TAPE STOP/EJECT PLAY STOP/EJECT CD RADIO BAND AUTO PRESET REC SLEEP SLEEP Erase head Pinch roller Record/playback head Capstan Lens Use TYPE I (normal) tape only. Supplied accessory AC power cord (1) Remote control (1) (CFD-S36 only) Design and specifications are subject to change without notice. Optional accessories Sony MDR headphone series Use TYPE I (normal) tape only.

Sony Corporation ©2001 Operating Instructions Manual de instrucciones CD Radio Cassette- Corder 3-227-155-43 (2) CFD-S26 CFD-S26L CFD-S36 CFD-S36L CFD-926L Connect the mains lead A or insert six R20 (size D) batteries (not supplied) into the battery compartment B . Notes • Replace the batteries when the OPR/BATT indicator dims or when the player stops operating. Replace all the batteries with new ones. Before you replace the batteries, be sure to take out the CD from the player. • To use the player on batteries, disconnect the mains lead from the player. • When you operate the player on batteries, you cannot turn on the player using the remote (CFD-S36/ S36L only). Brazilian model only: Adjusting the voltage C Be sure to set the VOLTAGE SELECTOR (at the bottom) to your local power supply. Tip Only for the customers supplied with an AC plug adaptor: Use the supplied AC plug adaptor if the plug of the main lead does not match your outlet. Preparing the remote D (CFD-S36/S36L only) Insert two R6 (size AA) batteries (not supplied). Replacing batteries With normal use, the batteries should last for about six months. When the remote no longer operates the player, replace all the batteries with new ones. Power Sources/Fuentes de alimentación 1 to AC IN a AC IN 2 to the mains a la toma de corriente A B C D Español Precauciones Seguridad • Puesto que el haz láser utilizado en la sección del reproductor de CD es perjudicial para los ojos, no intente desmontar la caja. Solicite asistencia técnica únicamente a personal especializado. • Si se introduce algún objeto sólido o líquido en el reproductor, desenchúfelo y haga que sea examinado por personal especializado antes de volver a utilizarlo. • Los discos con formas no estándar (p.ej., corazón, cuadrado, estrella) no pueden reproducirse en este reproductor. Si lo intenta, puede dañar el reproductor. No utilice tales discos. Limpieza del exterior • Limpie el exterior, el panel y los controles con un paño suave ligeramente humedecido con una solución detergente poco concentrada. No utilice estropajos abrasivos, detergente en polvo ni disolventes, como alcohol o bencina. Fuentes de alimentación • Cuando lo alimente con CA, compruebe que la tensión de funcionamiento del reproductor coincide con la del suministro eléctrico local (consulte “Especificaciones”) y utilice el cable de corriente suministrado; no emplee otro tipo de cable. El selector de tensión está situado en la parte inferior del reproductor (sólo modelo para Brasil). • El reproductor no estará desconectado de la fuente de alimentación de CA (toma de corriente) mientras esté conectado a la toma mural, aunque haya apagado el propio reproductor. • Para alimentar la unidad con pilas, utilice seis pilas R20 (tamaño D). • Cuando no vaya a utilizar las pilas, extráigalas para evitar daños que pueden producirse por la fuga o corrosión de las mismas. • La placa de características que indica la tensión de funcionamiento, consumo de energía, etc. está situada en la parte inferior. Ubicación • No deje el reproductor cerca de fuentes de calor, ni en lugares sujetos a la luz solar directa, polvo excesivo o golpes mecánicos. • No coloque el reproductor en lugares inclinados ni inestables. • No coloque nada a una distancia inferior a 10 mm del lateral del sistema. Los orificios de ventilación no deben bloquearse con el fin de que el reproductor funcione correctamente y prolongar la duración de sus componentes. • Si deja el reproductor en un automóvil aparcado al sol, elija un lugar dentro de dicho automóvil en el que el reproductor no quede expuesto a los rayos directos del sol. • Puesto que los altavoces utilizan un imán potente, mantenga las tarjetas personales de crédito que utilicen codificación magnética o los relojes de cuerda alejados del reproductor para evitar posibles daños producidos por dicho imán. Especificaciones Sección del reproductor de CD Sistema Sistema de audio digital de discos compactos Propiedades del diodo láser Material: GaAlAs Longitud de onda: 780 nm Duración de la emisión: Continua Salida de láser: Inferior a 44,6 µW (Esta salida es el valor medido a una distancia de unos 200 mm de la superficie de la lente objetiva del bloque de recogida óptica con una apertura de 7 mm.) Velocidad del eje 200 r/min (rpm) a 500 r/min (rpm) (CLV) Número de canales 2 Respuesta de frecuencia 20 - 20 000 Hz +1/–2 dB Fluctuación y trémolo Inferior al límite medible Sección de la radio Margen de frecuencias CFD-S26/S36 FM 87,6 - 107 MHz (Modelo coreano) 87,6 - 108 MHz (Otros modelos) AM 531 - 1 602 kHz (intervalo de 9 kHz) 530 - 1 610 kHz (intervalo de 10 kHz) CFD-S26L/S36L/926L FM 87,5 - 108 MHz MW 531 - 1 602 kHz (intervalo de 9 kHz) 530 - 1 610 kHz (intervalo de 10 kHz) LW 153 - 279 kHz IF FM: 10,7 MHz AM/MW/LW: 450 kHz Antenas FM: Antena telescópica AM/MW/LW: Antena de barra de ferrita incorporada Sección de la grabadora de cassettes Sistema de grabación 4 pistas y 2 canales estéreo Tiempo de bobinado rápido Aprox. 120 s (seg.) con casetes Sony C-60 Respuesta de frecuencia TYPE I (normal): 70 - 10 000 Hz Generales Altavoz Gama completa: 10 cm de diámetro, 3,2 ohmios, tipo cónico (2) Salidas Toma de auriculares (minitoma estéreo) Para auriculares de impedancia de 16 a 68 ohmios Salida de potencia máxima 4,6 W Requisitos de alimentación Para la grabadora de casetes, radio y CD: Modelo para Brasil: 110 - 120V, 220 - 240V CA seleccionable, 50/60 Hz Modelo argentino: 220 - 230 V CA, 50 Hz Modelo coreano: 220 V CA, 60 Hz Otros modelos: 230 V CA, 50 Hz 9 V CC, 6 pilas R20 (tamaño D) Para el mando a distancia (sólo CFD-S36/S36L): 3 V CC, 2 pilas R6 (tamaño AA) Consumo de energía CA 20 W Duración de las pilas Para la grabadora de casetes, radio y CD: Grabación de FM Sony R20P: aprox. 13,5 h Alcalinas Sony LR20: aprox. 20 h Reproducción de cintas Sony R20P: aprox. 7,5 h Alcalinas Sony LR20: aprox. 15 h Reproducción de CD Sony R20P: aprox. 2,5 h Alcalinas Sony LR20: aprox. 7 h Solución de problemas General La alimentación no se activa. • Asegúrese de que las pilas están insertadas correctamente. • Sustituya todas las pilas por unas nuevas si disponen de poca energía. • No es posible encender el reproductor con el mando a distancia al utilizar dicho reproductor con pilas (sólo CFD-S36/S36L). La alimentación no se activa y “bAttErY” y “Error” aparecen alternativamente. • Asegúrese de que las pilas están insertadas correctamente. • Sustituya todas las pilas por unas nuevas si disponen de poca energía. Ausencia de sonido. • Ajuste el volumen. • Desenchufe los auriculares cuando escuche el sonido a través de los altavoces. Se oye ruido. • Alguien está utilizando un teléfono móvil u otro equipo que emite ondas de radio cerca del reproductor. t Aleje el teléfono móvil, etc., del reproductor. Reproductor de CD El CD no se reproduce o “no dISC” se ilumina en el visor aunque haya un CD insertado. • Coloque el CD con la superficie de la etiqueta hacia arriba. • Límpielo. • Extraiga el CD y deje el compartimiento abierto durante una hora aproximadamente hasta que se seque la condensación de humedad. • El CD-R/CD-RW no está finalizado. Finalice el CD-R/CD-RW con el dispositivo de grabación. • Existe un problema con la calidad del CD-R/ CD-RW, el dispositivo de grabación o el software de aplicación. Se producen pérdidas de sonido. • Reduzca el volumen. • Limpie el CD, o sustitúyalo si está gravemente dañado. • Coloque el reproductor en un lugar sin vibraciones. • Limpie la lente con un soplador disponible en el mercado. • Pueden producirse pérdidas de sonido o ruido si se utilizan discos CD-R/CD-RW de mala calidad o si existe algún problema con el dispositivo de grabación o el software de aplicación. Radio La recepción es de mala calidad. • Cambie la orientación de la antena para mejorar la recepción de FM. • Cambie la orientación del reproductor para mejorar la recepción de AM o de MW/LW. El sonido es débil o de mala calidad. • Sustituya todas las pilas por unas nuevas si disponen de poca energía. • Aleje el reproductor del TV. La imagen del TV es inestable. • Si escucha un programa de FM cerca de un TV con una antena interior, aleje el reproductor de dicho TV. Utilización • Si traslada el reproductor directamente de un lugar frío a uno cálido, o si lo instala en una sala muy húmeda, es posible que se condense humedad en las lentes del interior de la sección de reproductor de CD. Si esto ocurre, el reproductor no funcionará correctamente. En este caso, extraiga el CD y espere una hora aproximadamente hasta que se evapore la humedad. • Si no ha utilizado el reproductor durante mucho tiempo, ajústelo en el modo de reproducción para que se caliente durante unos minutos antes de insertar un casete. Notas sobre los casetes • Rompa la lengüeta de la cara A o B del casete para evitar grabaciones accidentales. Si desea utilizar la cinta de nuevo para grabar, cubra el orificio de la lengüeta rota con cinta adhesiva. • No se recomienda el uso de casetes de duración superior a 90 minutos, excepto para realizar grabaciones o reproducciones largas y continuas. Notas sobre los discos compactos • Antes de realizar la reproducción, limpie el CD con un paño de limpieza. Hágalo desde el centro hacia los bordes. • No utilice disolventes como bencina, diluyente, limpiadores disponibles en el mercado ni aerosoles antiestáticos para discos de vinilo. • No exponga el CD a la luz solar directa ni a fuentes de calor, como conductos de aire caliente, ni lo deje en un automóvil aparcado bajo la luz solar directa, ya que puede producirse un considerable aumento de temperatura en el interior del mismo. • No adhiera papel ni pegatinas en el CD, ni arañe su superficie. • Después de la reproducción, guarde el CD en su caja. Si el CD está arañado, sucio o hay huellas dactilares en el mismo, pueden producirse errores de lectura. Acerca de discos CD-R/CD-RW Este reproductor es compatible con discos CD-R/CD-RW, aunque la capacidad de reproducción puede variar en función de la calidad del disco, el dispositivo de grabación y el software de aplicación. Si desea realizar alguna consulta o solucionar algún problema referente al reproductor, consulte con el proveedor Sony más próximo. Reproductor de cintas La cinta no se mueve al pulsar un botón de funcionamiento. • Cierre firmemente el compartimiento de cassettes. El botón REC z no funciona o la cinta no se reproduce ni se graba. • Compruebe que el cassette dispone de lengüeta de seguridad. Reproducción, grabación o borrado de mala calidad o distorsionados. • Limpie los cabezales, el rodillo de apriete y el cabrestante con un bastoncillo ligeramente humedecido con un líquido limpiador o con alcohol. • Sustituya todas las pilas por unas nuevas si disponen de poca energía. • Utiliza una cinta TYPE II (posición alta) o TYPE IV (de metal). Utilice solamente cintas TYPE I (normales). • Desmagnetice los cabezales con un desmagnetizador de cabezales de cinta disponible en el mercado. Mando a distancia (sólo CFD-S36/ S36L) El mando a distancia no funciona. • Sustituya todas las pilas del mando a distancia por unas nuevas si disponen de poca energía. • Cerciórese de que orienta el mando a distancia hacia el sensor de control remoto del reproductor. • Elimine los obstáculos que haya entre el mando a distancia y el reproductor. • Compruebe que el sensor de control remoto no esté expuesto a iluminaciones intensas, como a la luz solar directa o a lámparas fluorescentes. • Acérquese al reproductor cuando utilice el mando a distancia. Si sigue teniendo problemas tras intentar las anteriores soluciones sugeridas, desenchufe el cable de corriente y extraiga todas las pilas. Cuando hayan desaparecido todas las indicaciones del visor, enchufe el cable de alimentación e inserte las pilas de nuevo. Si el problema persiste, consulte con el proveedor Sony más próximo. Cabezal de borrado Rodillo de apriete Cabezal de grabación/reproducción Cabrestante Lente Dimensiones Aprox. 420 × 159 × 284 mm (an/al/prf) (16 5⁄8 × 6 3⁄8 × 11 1⁄4 pulgadas) (partes salientes incluidas) Peso Aprox. 3,8 kg (8 lb. 6 oz) (pilas incluidas) Accesorio suministrado Cable de corriente (1) Mando a distancia (1) (sólo CFD-S36/S36L) El diseño y las especificaciones están sujetos a cambios sin previo aviso. Accesorios opcionales Auriculares Sony de la serie MDR Lengüeta de la cara B Lengüeta de la cara A Cara A Conecte el cable de corriente A o inserte seis pilas R20 (tamaño D) (no suministradas) en el compartimiento correspondiente B. Notas • Sustituya las pilas cuando el indicador OPR/BATT se atenúe o el reproductor deje de funcionar. Sustituya todas las pilas por otras nuevas. Antes de sustituir las pilas, asegúrese de extraer el CD del reproductor. • Para utilizar el reproductor con pilas, desconecte el cable de corriente de dicho reproductor. • Al utilizar el reproductor con pilas, no es posible encenderlo con el mando a distancia (sólo CFD-S36/ S36L). Sólo modelo para Brasil: Ajuste de la tensión C Asegúrese de ajustar el selector de tensión (VOLTAGE SELECTOR) (situado en la parte inferior) de acuerdo con la tensión del suministro eléctrico local. Sugerencia Sólo para los clientes a los que se haya suministrado un adaptador de enchufe de CA: Utilice el adaptador de enchufe de CA suministrado si el enchufe del cable de corriente no encaja en la toma de alimentación. Preparación del mando a distancia D (sólo CFD-S36/S36L) Inserte dos pilas R6 (tamaño AA) (no suministradas). Sustitución de las pilas Con un uso normal, las pilas deben durar aproximadamente seis meses. Cuando el reproductor no responda al mando a distancia, sustituya todas las pilas por unas nuevas. English Precautions On safety • As the laser beam used in the CD player section is harmful to the eyes, do not attempt to disassemble the casing. Refer servicing to qualified personnel only. • Should any solid object or liquid fall into the player, unplug the player, and have it checked by qualified personnel before operating it any further. • Discs with non-standard shapes (e.g., heart, square, star) cannot be played on this player. Attempting to do so may damage the player. Do not use such discs. Cleaning the cabinet • Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzine. On power sources • For AC operation, check that the player's operating voltage is identical with your local power supply (see "Specifications") and use the supplied mains lead; do not use any other type. The voltage selector is located at the bottom of the player (for Brazilian model only). • The player is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the player itself has been turned off. • For battery operation, use six R20 (size D) batteries. • When the batteries are not to be used, remove them to avoid damage that can be caused by battery leakage or corrosion. • The nameplate indicating operating voltage, power consumption, etc. is located at the bottom. On placement • Do not leave the player in a location near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock. • Do not place the player on an inclined or unstable place. • Do not place anything within 10 mm of the side of the cabinet. The ventilation holes must be unobstructed for the player to operate properly and prolong the life of its components. • If the player is left in a car parked in the sun, be sure to choose a location in the car where the player will not be subjected to the direct rays of the sun. • Since a strong magnet is used for the speakers, keep personal credit cards using magnetic coding or spring-wound watches away from the player to prevent possible damage from the magnet. Specifications CD player section System Compact disc digital audio system Laser diode properties Material: GaAlAs Wave length: 780 nm Emission duration: Continuous Laser output: Less than 44.6 µW (This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.) Spindle speed 200 r/min (rpm) to 500 r/min (rpm) (CLV) Number of channels 2 Frequency response 20 - 20 000 Hz +1/–2 dB Wow and flutter Below measurable limit Radio section Frequency range CFD-S26/S36 FM 87.6 - 107 MHz (Korean model) 87.6 - 108 MHz (Other models) AM 531 - 1 602 kHz (9 kHz step) 530 - 1 610 kHz (10 kHz step) CFD-S26L/S36L/926L FM 87.5 - 108 MHz MW 531 - 1 602 kHz (9 kHz step) 530 - 1 610 kHz (10 kHz step) LW 153 - 279 kHz IF FM: 10.7 MHz AM/MW/LW: 450 kHz Aerials FM: Telescopic aerial AM/MW/LW: Built-in ferrite bar aerial Cassette-corder section Recording system 4-track 2 channel stereo Fast winding time Approx. 120 s (sec.) with Sony cassette C-60 Frequency response TYPE I (normal): 70 - 10 000 Hz General Speaker Full range: 10 cm dia., 3.2 ohms, cone type (2) Outputs Headphones jack (stereo minijack) For 16 - 68 ohms impedance headphones Maximum power output 4.6 W Power requirements For CD radio cassette-corder: Brazilian model: 110 - 120V, 220 - 240V AC selectable, 50/60 Hz Argentine model: 220 - 230 V AC, 50 Hz Korean model: 220 V AC, 60 Hz Other models: 230 V AC, 50 Hz 9 V DC, 6 R20 (size D) batteries For remote control (CFD-S36/S36L only): 3 V DC, 2 R6 (size AA) batteries Power consumption AC 20 W Battery life For CD radio cassette-corder: FM recording Sony R20P: approx. 13.5 h Sony alkaline LR20: approx. 20 h Tape playback Sony R20P: approx. 7.5 h Sony alkaline LR20: approx. 15 h CD playback Sony R20P: approx. 2.5 h Sony alkaline LR20: approx. 7 h Troubleshooting General The power does not come on. • Make sure the batteries are inserted correctly. • Replace all the batteries with new ones if they are weak. • You cannot turn on the player with the remote when you operate the player on batteries (CFD-S36/S36L only). The power is not on, and "bAttErY" and “Error” are displayed alternately. • Make sure the batteries are inserted correctly. • Replace all the batteries with new ones if they are weak. There is no audio. • Adjust the volume. • Unplug the headphones when listening through speakers. Noise is heard. • Someone is using a portable telephone or other equipment that emits radio waves near the player. tMove the portable telephone, etc., away from the player. CD Player The CD does not play or “no dISC” lights in the display even when a CD is in place. • Place the CD with the label surface up. • Clean the CD. • Take out the CD and leave the CD compartment open for about an hour to dry moisture condensation. • The CD-R/CD-RW was not finalized. Finalize the CD-R/CD-RW with the recording device. • There is a problem with the quality of the CD- R/CD-RW, recording device, or application software. The sound drops out. • Reduce the volume. • Clean the CD, or replace it if the CD is badly damaged. • Place the player in a location free from vibration. • Clean the lens with a commercially available blower. • The sound may drop out or noise may be heard when using poor quality CD-Rs/CD- RWs or if there is a problem with the recording device or application software. Radio Reception is poor. • Reorient the aerial to improve FM reception. • Reorient the player itself to improve AM or MW/LW reception. The audio is weak or has poor quality. • Replace all the batteries with new ones if they are weak. • Move the player away from the TV. The picture of your TV becomes unstable. • If you are listening to an FM program near the TV with an indoor aerial, move the player away from the TV. On operation • If the player is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lenses inside the CD player section. Should this occur, the player will not operate properly. In this case, remove the CD and wait about an hour for the moisture to evaporate. • If the player has not been used for a long time, set it in the playback mode to warm it up for a few minutes before inserting a cassette. Notes on cassettes • Break off the cassette tab from side A or B to prevent accidental recording. If you want to reuse the tape for recording, cover the broken tab with adhesive tape. • The use of a cassette with more than 90 minutes of play time is not recommended except for long, continuous recording or playback. Notes on CDs • Before playing, clean the CD with a cleaning cloth. Wipe the CD from the center out. • Do not use solvents such as benzine, thinner, commercially available cleaners or anti-static spray intended for vinyl LPs. • Do not expose the CD to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight as there can be a considerable rise in temperature inside the car. • Do not stick paper or sticker on the CD, nor scratch the surface of the CD. • After playing, store the CD in its case. If there is a scratch, dirt or fingerprints on the CD, it may cause tracking error. About CD-Rs/CD-RWs This player is compatible with CD-Rs/CD- RWs but playback capability may vary depending on the quality of the disc, the recording device and application software. If you have any questions or problems concerning your player, please consult your nearest Sony dealer. Tape Player The tape does not move when you press an operation button. • Close the cassette compartment securely. The REC z button does not function or the tape does not play or record. • Make sure the safety tab on the cassette is in place. Poor or distorted playback, recording or erasing quality. • Clean the heads, pinch roller and capstan with a cleaning swab slightly moistened with cleaning fluid or alcohol. • Replace all the batteries with new ones if they are weak. • TYPE II (high position) or TYPE IV (metal) tape is being used. Use TYPE I (normal) tape only. • Demagnetize the heads using a commercially available tape head demagnetizer. Remote (CFD-S36/S36L only) The remote does not function. • Replace all the batteries in the remote with new ones if they are weak. • Make sure that you are pointing the remote at the remote sensor on the player. • Remove any obstacles in the path of the remote and the player. • Make sure the remote sensor is not exposed to strong light such as direct sunlight or fluorescent lamp light. • Move closer to the player when using the remote. After trying the above remedies, if you still have problems, unplug the mains lead and remove all the batteries. After all the indications in the display disappear, plug the power cord and insert the batteries again. If the problem persists, please consult your nearest Sony dealer. Erase head Pinch roller Record/playback head Capstan Lens Dimensions Approx. 420 × 159 × 284 mm (w/h/d) (16 5⁄8 × 6 3⁄8 × 11 1⁄4 inches) (incl. projecting parts) Mass Approx. 3.8 kg (8 lb. 6 oz) (incl. batteries) Supplied accessory Mains lead (1) Remote control (1) (CFD-S36/S36L only) Design and specifications are subject to change without notice. Optional accessories Sony MDR headphone series Side A Tab for side B Tab for side A English WARNING To prevent fire or shock hazard, do not expose the player to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Information For customers in Europe This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT mark is located at the rear. WARNING Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the appliance. Notice for customers in the United Kingdom A moulded plug complying with BS 1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced, same rating fuse approved by ASTA or BSI to BS 1362, (i.e. marked with or mark) must be used. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station. Español ADVERTENCIA Para evitar el riesgo de incendios o electrocución, no exponga el reproductor a la lluvia ni a la humedad. Para evitar descargas eléctricas, no abra el aparato. Solicite asistencia técnica únicamente a personal especializado. Información Para clientes en Europa Este reproductor de discos compactos está clasificado como producto LÁSER DE CLASE 1. La etiqueta CLASS 1 LASER PRODUCT se encuentra en la parte posterior. ADVERTENCIA No instale el aparato en un espacio cerrado, como una estantería para libros o un armario empotrado. Para evitar el peligro de incendio o descarga eléctrica, no coloque objetos con líquido, como jarrones, sobre el aparato.

1 CD Model Name Using Similar Mechanism CFD-S22/S32 Section CD Mechanism Type KSM-213CDP Optical Pick-up Name KSS-213C TC Model Name Using Similar Mechanism CFD-V5 Section Tape Transport Mechanism Type MF-V5-117 SERVICE MANUAL US Model E Model Australian Model CFD-S26 CD RADIO CASSETTE-CORDER Other Specifications CD player section System Compact disc digital audio system Laser diode properties Material: GaAlAs Wave length: 780 nm Emission duration: Continuous Laser output: Less than 44.6 µW (This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.) Spindle speed 200 r/min (rpm) to 500 r/min (rpm) (CLV) Number of channels 2 Frequency response 20 - 20,000 Hz +1/–2 dB Wow and flutter Below measurable limit SPECIFICATIONS – Continued on next page – Radio section Frequency range FM: 87.6 - 108 MHz US, E92, MX model: AM: 530 - 1,710 kHz SP, AR, AUS, E4 model: AM: 531 - 1,602 kHz (9 kHz step) AM: 530 - 1,610 kHz (10 kHz step) Antennas FM: Telescopic antenna AM: Built-in ferrite bar antenna Cassette-corder section Recording system 4-track 2 channel stereo Fast winding time Approx. 120 sec. with Sony cassette C-60 Frequency response TYPE I (normal): 80 - 10,000 Hz Photo: SILVER Ver 1.2 2002. 06 9-873-112-13 2002F0400-1 © 2002. 06 AUDIO POWER SPECIFICATIONS (US model) POWER OUTPUT AND TOTAL HARMONIC DISTORTION With 3.2-ohm loads, both channels driven from 150 - 6,300 Hz; rated 1.8 W per channel- minimum RMS power, with no more than 10% total harmonic distortion in AC operation. Sony Corporation Personal Audio Company Published by Sony Engineering Corporation

® General Stereo/Hifi Components/Tape Decks CD Players/Mini Disc Players/Audio Systems LIMITED WARRANTY Sony Electronics Inc. (“Sony”) warrants this Product (including any accessories) against defects in material or workmanship as follows: 1. LABOR: For a period of one (1) year from the date of purchase, if this Product is determined to be defective, Sony will repair or replace the Product, at its option, at no charge, or pay the labor charges to any Sony autho- rized service facility. After the Warranty Period, you must pay for all labor charges. 2. PARTS: In addition, Sony will supply, at no charge, new or rebuilt replacements in exchange for defective parts for a period of one (1) year. After the warranty period, you must pay for all parts costs. 3. ACCESSORIES: Parts and labor for all accessories are for one (1) year. To obtain warranty service, you must take the Product, or deliver the Product freight prepaid, in either its original packaging or packaging affording an equal degree of protection, to any authorized Sony service facility. This warranty does not cover customer instruction, installation, set up adjustments or signal reception prob- lems. This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negli- gence, commercial use, or modification of, or to any part of the Product, including the antenna. This warranty does not cover damage due to improper operation or maintenance, connection to improper voltage supply, or attempted repair by anyone other than a facility authorized by Sony to service the Product. This warranty does not cover Products sold AS IS or WITH ALL FAULTS, or consumables (such as fuses or batteries). This warranty is valid only in the United States. Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the unit is within the Warranty period must be presented to obtain warranty service. This warranty is invalid if the factory applied serial number has been altered or removed from the Product. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. SONY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. EXCEPT TO THE EXTENT PROHIB- ITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICU- LAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. In addition, if you enter into a service contract with the Sony Partnership within 90 days of the date of sale, the limitation on how long an implied warranty lasts does not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. For your convenience, Sony Electronics Inc. has established telephone numbers for frequently asked questions: To locate the servicer or dealer nearest you, or for service assistance or resolution of a service problem, or for product information or operation, call: Sony Customer Information Services Center 1-800-222-7669 or visit the Sony Web Site: www.sony.com For an accessory or part not available from your authorized dealer, call: 1-800-488-SONY (7669) Hifi Audio 4-557-172-02 Printed in Japan