Document Preview & Text Transcription
CFD-S40CP
SERVICE MANUAL
CD RADIO CASSETTE-CORDER
SPECIFICATIONS
US Model
Canadian Model
AEP Model
UK Model
E Model
Model Name Using
CD Section
CFD-V3/V7/V7L
Similar Mechanism
Tape Section
CFD-V3/V5/V7/V7L
CD Mechanism Type
KSM-213CDM
Optical Pick-up Type
KSS-213C
Tape Transport Mechanism Type
MF-V5-117
– Continued on page 2 –
Ver. 1.3 2005.09
9-873-092-14
2005I02-1
© 2005.09
AUDIO POWER SPECIFICATIONS (US Model)
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION
With 3.2-ohm loads, both channels driven from
150 - 10,000 Hz; rated 1.8 W per channel-minimum
RMS power, with no more than 10 %
total harmonic distortion in AC operation.
Other Specifications
CD player section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of about
200 mm from the objective lens surface on the optical
pick-up block with 7 mm aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of channels
2
Frequency response
20 - 20 000 Hz +1/–2 dB
Wow and flutter
Below measurable limit
Radio section
Frequency range
FM: 87.5 - 108 MHz
AM: 530 - 1,710 kHz (US, CND, KR, TW)
MW: 531 - 1,611 kHz (AEP, UK)
LW: 153 - 279 kHz (AEP, UK)
Antennas
FM: Telescopic antenna
AM: Built-in ferrite bar antenna
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 120 sec. with Sony cassette C-60
Frequency response
TYPE I (normal): 70 - 13 000 Hz
General
Speaker
Full range: 10 cm (4 in.) dia.,
3.2 Ω, cone type (2)
Outputs
Headphones jack (stereo minijack)
For 16 - 68 Ω impedance headphones
Power output
2.3 W + 2.3 W (at 3.2 Ω, 10 % harmonic
distortion)
Sony Corporation
Personal Audio Group
Pubulished by Sony Engineering Corporation
2
CFD-S40CP
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
TABLE OF CONTENTS
Specifications ............................................................................... 1
1.
SERVICING NOTES ...................................................... 3
2.
GENERAL
Location and Function of Controls ....................................... 4
3.
DISASSEMBLY
3-1. Cabinet (Front) ASSY, Cabinet (Rear) ........................ 7
3-2. Control Board .............................................................. 8
3-3. Headphone Board ........................................................ 8
3-4. Cabinet (Upper) ASSY ................................................ 9
3-5. LCD Board (with Lamp Board)................................... 9
3-6. Main Board ................................................................ 10
3-7. CD Board ................................................................... 10
3-8. Optical Pick-up Block, Mechanism Deck,
CD motor Board, TC Board ....................................... 11
3-9. M321 (Capstan/Reel Motor), Belt,
HRP301 Head, Magnetic (Record/Playback),
HE301 Head (Erase) .................................................. 11
3-10. Power ASSY, Battery Board,
Battery Common Board............................................. 12
3-11. Tuner Board ............................................................... 12
4.
ADJUSTMENTS
4-1. Mechanical Adjustments ........................................... 13
4-2. Electrical Adjustments ............................................... 13
5.
DIAGRAMS
5-1. Explanation of IC Terminals...................................... 17
5-2. Block Diagram – Tuner/TC Section – ....................... 20
5-3. Block Diagram – Main Section – .............................. 21
5-4. Block Diagram – CD Section – ................................. 22
5-5. Printed Wiring Board – TC Section – ........................ 23
5-6. Schematic Diagram – TC Section – .......................... 23
5-7. Printed Wiring Board
– Tuner Section (US, Canadian, KR, TW Model) – .. 24
5-8. Schematic Diagram
– Tuner Section (US, Canadian, KR, TW Model) – .. 25
5-9. Printed Wiring Board
– Tuner Section (AEP, UK Model) – ......................... 26
5-10. Schematic Diagram
– Tuner Section (AEP, UK Model) – ......................... 27
5-11. Printed Wiring Board – CD Section – ....................... 28
5-12. Schematic Diagram – CD Section (1/2) – ................. 29
5-13. Schematic Diagram – CD Section (2/2) – ................. 30
5-14. Schematic Diagram – Main Section (1/2) – .............. 31
5-15. Schematic Diagram – Main Section (2/2) – .............. 32
5-16. Printed Wiring Board – Main Section – .................... 33
5-17. Printed Wiring Board – Power Supply Section – ...... 34
5-18. Schematic Diagram – Power Supply Section – ......... 34
6.
EXPLODED VIEWS
6-1. Front Cabinet Section ................................................ 40
6-2. Rear Cabinet Section ................................................. 41
6-3. Upper Cabinet Section ............................................... 42
6-4. Mechanism Deck Section (1) .................................... 43
6-5. Mechanism Deck Section (2) .................................... 44
6-6. CD Block Section ...................................................... 45
7.
ELECTRICAL PARTS LIST ...................................... 46
CAUTION
Use of controls or adjustments or performance
of procedures other than those specified herein
may result in hazardous radiation exposure.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
This Compact Disc player is classified as a CLASS 1 LASER
product.
The CLASS 1 LASER PRODUCT label is located at the bottom
of the player.
Information
For customers in Europe
Power requirements
For CD radio cassette-corder:
120 V AC, 60 Hz (US, CND, TW)
230 V AC, 50 Hz (AEP, UK, KR)
9 V DC, 6 size D (R20) batteries
For memory back-up:
6 V DC, 4 size AA (R6) batteries
For remote control:
3 V DC, 2 size AA (R6) batteries
Power consumption
AC 20 W
Battery life
For CD radio cassette-corder:
FM recording
Sony R20P: approx. 15 h
Sony alkaline LR20: approx. 40 h
Tape playback
Sony R20P: approx. 10 h
Sony alkaline LR20: approx. 25 h
CD playback
Sony R20P: approx. 1.5 h
Sony alkaline LR20: approx. 6 h
Dimensions
Approx. 420 × 161 × 266 mm (w/h/d)
(16 5 ⁄8 × 6 3 ⁄8 × 10 1 ⁄2 inches) (incl. projecting parts)
Mass
Approx. 4.6 kg (10 lb. 2 oz) (incl. batteries)
Supplied accessories
AC power cord (1)
Remote control (1)
Design and specifications are subject to change without
notice.
Ver 1.1 2001.07
3
CFD-S40CP
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro-
static breakdown because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic breakdown and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled
with care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode
emission, observe more than 30 cm away from the objective
lens.
CHUCK PLATE JIG ON REPAIRING
On repairing CD section, playing a disc without the CD lid, use
Chuck Plate Jig.
• Code number of Chuck Plate Jig : X-4918-255-1
SECTION 1
SERVICING NOTES
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
1.
Press CD open knob.
2.
Open the lid for CD.
3.
Push on SWITCH (S701) as following figure.
4.
Confirm the laser diode emission while observing the
objecting lens. When there is no emission, Auto Power
Control circuit or Optical Pick-up is broken.
Objective lens moves up and down once for the focus
search.
To Exposed Metal
Parts on Set
0.15µF
1.5kΩ
AC
voltmeter
(0.75V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY CHECK-OUT (US model)
After correcting the original service problem, perform the
following safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage. Check
leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The “limit” indication is 0.75
V, so analog meters must have an accurate low-voltage scale.
The Simpson 250 and Sanwa SH-63Trd are examples of a pas-
sive VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2V AC range are suitable. (See Fig. A)
Insert a precision
screw driver and push
SWITCH (S701)
