Sony RM-VZ220 Manuals

4-170-642-22(1) Remote Commander RM-VZ220 ©2010 Sony Corporation Printed in China Operating Instructions Mode d’emploi (au verso) English For the Customers in the U.S.A. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: �Reorient or relocate the receiving antenna. �Increase the separation between the equipment and receiver. �Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. �Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. For customers in Canada This Class B digital apparatus complies with Canadian ICES-003. Setting Up the RM-VZ220 The RM-VZ220 is preset at the factory to operate Sony brand video devices set to any of the Device Select buttons (see the table below). To use with non-Sony devices, or Sony devices that are not preset at the factory, set the manufacturer’s code for each device. Devices Button Factory setting* TV TV Sony TV (00810) TV, Cable set top box, Satellite receiver, IPTV, DVD player, DVD recorder, Blu-ray Disc player, DVR (digital video recorder), PVR (personal video recorder), VCR, DVD Home Theater CBL (SAT) Cable set top box (non- Sony) (51376) VCR Sony VCR (60032) DVD Sony DVD player (11033) * The five-digit code is the preset manufacturer’s code. Note Only a TV can be assigned to the TV Device Select button. You can assign any device to the other Device Select buttons. Installing the batteries Slide open the battery compartment and insert two size AA (R6) dry batteries (not supplied). Insert the batteries (negative end first) through the guide clamp within each compartment as shown below. 1 2 Battery life Under normal conditions, size AA (LR6) alkaline batteries will last up to one year. If the RM-VZ220 does not operate properly, the batteries might be drained. Replace both batteries with new ones. Notes �Replace the batteries within 2 minutes after removing them, and do not press any button when replacing the batteries. Otherwise, your code settings may be cleared. �Do not use an old battery with a new one, or mix different types of batteries together. �If the electrolyte inside the battery should leak, wipe the contaminated area of the battery compartment with a cloth and replace the old batteries with new ones. To prevent electrolyte from leaking, remove the batteries when you plan not to use the RM-VZ220 for a long period of time. Specifications Operating distance Approx. 11 m (36 ft) (varies depending on devices of different manufacturers) Power requirements Two size AA (R6) dry batteries (not supplied) Battery life Approx. 1 year when using size AA (LR6) alkaline batteries (varies depending on frequency of button use - up to approx. 300 times per day.) Dimensions Approx. 53 × 213 × 27 mm (2 1/8 × 8 1/2 × 1 1/8 in.) (w/h/d) Mass Approx. 100 g (3.5 oz) (not including batteries) Design and specifications are subject to change without notice. Troubleshooting If you have problems setting up or using the RM-VZ220: �Carefully perform the setup procedure of “Startup Guide.” If the RM-VZ220 does not work, try repeating the setup procedure using another manufacturer’s code (if listed for your device). If you still cannot operate the RM-VZ220, try the Search function (see “Searching for the correct code”). �Aim the RM-VZ220 directly at the device. �Remove any obstacles in the path between the RM-VZ220 and the device. �Make sure you have pressed the correct Device Select button. �Check that the device has infrared remote capability. For example, if your device did not come with a remote control, it probably is not capable of being controlled by the RM-VZ220. �The batteries are weak, or not inserted correctly. Replace them with new ones or insert them correctly. Startup Guide This guide shows you how to set up and use the RM-VZ220 to operate your devices. If your Sony device has already been preset, see “Operate the device.” Set the manufacturer’s code Example: To set up a Philips TV 1 Find the manufacturer’s code in “Manufacturer’s Code List.” RM-VZ220_CA [US,FR] 4-170-642-22(1) RM-VZ220_CA [US,FR] 4-170-642-22(1) 4-170-642-22(1) Remote Commander RM-VZ220 ©2010 Sony Corporation Printed in China Operating Instructions Mode d’emploi (au verso) English For the Customers in the U.S.A. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: � Reorient or relocate the receiving antenna. � Increase the separation between the equipment and receiver. � Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. � Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. For customers in Canada This Class B digital apparatus complies with Canadian ICES-003. Setting Up the RM-VZ220 The RM-VZ220 is preset at the factory to operate Sony brand video devices set to any of the Device Select buttons (see the table below). To use with non-Sony devices, or Sony devices that are not preset at the factory, set the manufacturer’s code for each device. Devices Button Factory setting* TV TV Sony TV (00810) TV, Cable set top box, Satellite receiver, IPTV, DVD player, DVD recorder, Blu-ray Disc player, DVR (digital video recorder), PVR (personal video recorder), VCR, DVD Home Theater CBL (SAT) Cable set top box (non- Sony) (51376) VCR Sony VCR (60032) DVD Sony DVD player (11033) * The five-digit code is the preset manufacturer’s code. Note Only a TV can be assigned to the TV Device Select button. You can assign any device to the other Device Select buttons. Installing the batteries Slide open the battery compartment and insert two size AA (R6) dry batteries (not supplied). Insert the batteries (negative end first) through the guide clamp within each compartment as shown below. 1 2 Battery life Under normal conditions, size AA (LR6) alkaline batteries will last up to one year. If the RM-VZ220 does not operate properly, the batteries might be drained. Replace both batteries with new ones. Notes � Replace the batteries within 2 minutes after removing them, and do not press any button when replacing the batteries. Otherwise, your code settings may be cleared. � Do not use an old battery with a new one, or mix different types of batteries together. � If the electrolyte inside the battery should leak, wipe the contaminated area of the battery compartment with a cloth and replace the old batteries with new ones. To prevent electrolyte from leaking, remove the batteries when you plan not to use the RM-VZ220 for a long period of time. Specifications Operating distance Approx. 11 m (36 ft) (varies depending on devices of different manufacturers) Power requirements Two size AA (R6) dry batteries (not supplied) Battery life Approx. 1 year when using size AA (LR6) alkaline batteries (varies depending on frequency of button use - up to approx. 300 times per day.) Dimensions Approx. 53 × 213 × 27 mm (2 1/8 × 8 1/2 × 1 1/8 in.) (w/h/d) Mass Approx. 100 g (3.5 oz) (not including batteries) Design and specifications are subject to change without notice. Troubleshooting If you have problems setting up or using the RM-VZ220: � Carefully perform the setup procedure of “Startup Guide.” If the RM-VZ220 does not work, try repeating the setup procedure using another manufacturer’s code (if listed for your device). If you still cannot operate the RM-VZ220, try the Search function (see “Searching for the correct code”). � Aim the RM-VZ220 directly at the device. � Remove any obstacles in the path between the RM-VZ220 and the device. � Make sure you have pressed the correct Device Select button. � Check that the device has infrared remote capability. For example, if your device did not come with a remote control, it probably is not capable of being controlled by the RM-VZ220. � The batteries are weak, or not inserted correctly. Replace them with new ones or insert them correctly. Startup Guide This guide shows you how to set up and use the RM-VZ220 to operate your devices. If your Sony device has already been preset, see “Operate the device.” Set the manufacturer’s code Example: To set up a Philips TV 1 Find the manufacturer’s code in “Manufacturer’s Code List.” Manufacturer’s Code List / Liste des codes d’appareil par fabricant English The following tables show brand names (Brand) and their corresponding code numbers (Code No.). 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 2 Enter the manufacturer’s code. The SET indicator flashes three times and turns off. Français Le tableau ci-dessous indique des marques (Brand) et les codes correspondants (Code No.). 1 Maintenez la touche SET enfoncée pendant plus de 3 secondes. L’indicateur SET s’allume. Tout en maintenant la touche SET enfoncée, appuyez sur la touche de sélection d’appareil souhaitée, puis relâchez les deux touches. 2 Saisissez le code d’appareil du fabricant. L’indicateur SET clignote 3 fois, puis s’éteint. TV / Téléviseur Brand Code No. Sony 11633, 10533, 10864, 11033, 11070, 11431, 11516 Accurian 10675 Akai 10695 Allegro 10869 Apex Digital 10672, 11056 Bel Canto Design 11571 Broksonic 10695 CineVision 10869 Citizen 10695 CyberHome 11024 Daewoo 10869 Denon 10490, 11634, 12258 Disney 10675, 11270 Emerson 10591, 10675 Enterprise 10591 Funai 10675 GE 10522 GFM 10675 Go Video 10744, 10741, 10869, 11044, 11075 GoldStar 10741 Harman/Kardon 11229 Hitachi 10573, 10664 Hiteker 10672 Insignia 10675, 12428, 12596 Integra 11769, 10627, 12147 JVC 10623, 10867, 11164 Kenwood 10490 LG 10591, 10741, 10869 Magnavox 10503, 10539, 10646, 10675, 11354 Marantz 10539, 12414, 12432 Memorex 10695, 11270, 12213 Microsoft 10522, 12083 Mitsubishi 11521 NAD 10741, 12572 Olevia 12331 Brand Code No. Onkyo 10503, 11769, 10627, 11627, 12147 Oppo 10575, 12545 Panasonic 10490, 11579, 11641 Philco 10675 Philips 10503, 10539, 12056, 12084, 10646, 10675, 11267, 11354, 12434 Pioneer 10142, 10631, 11571, 12442 Polk Audio 10539 Presidian 10675 Proscan 10522 RCA 10522, 11769, 10822, 12213, 12587, 12592, 12594 Rio 10869 Rotel 10623 Samsung 10490, 10573, 10199, 11044, 11075, 12329, 12489 Sansui 10695 Sanyo 10695 Sharp 10630, 10675, 12250 Shinsonic 10533 Sonic Blue 10869 Sylvania 10675 Symphonic 10675 TCL 12587 Technics 10490 Tivo 11503 Toshiba 10503, 11769, 10695, 11154, 11503, 12006, 12277 Urban Concepts 10503 Viore 12553 Vizio 12563 Vtrek 12587 Xbox 10522, 12083 Yamaha 10490, 10539, 10497, 10817, 12298 Zenith 10503, 10591, 10741, 10869 DVD player / Lecteur DVD Brand Code No. Sony 11033, 11070, 11431 Accurian 10675 Apex Digital 11056 Funai 10675 Go Video 10741 JVC 11164 LG 10741 Magnavox 10646, 10675 Panasonic 10490, 11579 Brand Code No. Philips 10646 Pioneer 10631 RCA 10522 Samsung 10490 Sharp 10675 Sylvania 10675 Toshiba 12277 Zenith 10741 DVD recorder / Enregistreur DVD Brand Code No. Sony 00810, 00000 Acer 01339 Action 00650 Admiral 00463 Akai 00812, 01675, 00702, 02232 Akira 01733 AOC 01365, 01589 Apex Digital 00748 Aventura 00171 Bell & Howell 00154 BPL 01543 Broksonic 00463 Carver 00054 Celebrity 00000 Coby 02306, 02345, 02348 Commercial Solutions 01447 Crosley 00054 Curtis 02352 Curtis Mathes 00054, 00154, 00702, 01661 Daewoo 01661 Digital Lifestyles 01765 Durabrand 00463, 00171 Dynex 01463, 01810, 02049 Electroband 00000 Electrograph 01755 Electrohome 00463 Elektra 01661 Element 01687 Emerson 01864, 00154, 00463, 00171, 01661, 01394 Emprex 01765 Envision 01365, 01589 ESA 00812, 00171 Fisher 00154 Funai 00171 Gateway 01755, 01756 GE 01447, 00051, 02359 GFM 00171 Haier 01748, 01749, 02309, 02449 Harman/Kardon 00054 Hisense 00748, 01314, 02098 Hitachi 01643, 02215, 02433 iLo 01684 Infinity 00054 Insignia 01564, 00171, 02049 JBL 00054 JCB 00000 JVC 00731, 01253, 01601, 01774 KDS 01687 Kolin 01331 LG 01423, 02358 LXI 00054, 00154, 00156 MAG 01687 Magnavox 01454, 01866, 00054, 01254, 01365, 02372 Marantz 00054 Matsushita 00650 Maxent 01755 Memorex 00154, 00463, 00150 MGA 00150 Brand Code No. Midland 00051 Mitsubishi 01250, 00150, 00836 NAD 00156 NEC 01797 NetTV 01755 Norcent 00748, 01365, 01589 Olevia 01610, 01144, 01331 Onida 01253, 02396 Optimus 00154, 00650 Orion 00463, 01463 Panasonic 01480, 00051, 00650 PARK 02104 Penney 00156, 00051 Petters 01523 Philco 00054 Philips 01454, 00054, 00690, 01744, 02372 Pioneer 01457, 01260 Polaroid 01523, 01276, 01314, 01687 Portland 01661 Prism 00051 Proscan 01447, 02147, 02256 Proview 01687 Quasar 00051, 00650 RadioShack 00154 RCA 01447, 01781, 02187, 02247, 02403, 02429, 02434 Realistic 00154 Sampo 01755 Samsung 00812, 00702 Sansui 00463 Sanyo 00154, 01142 Sceptre 01360, 01599 Scott 01711 Sears 00054, 00154, 00156, 00171 Sharp 00818 Spectroniq 01687 Squareview 00171 Superscan 00864 Supreme 00000 SVA 00748 Sylvania 01864, 00054, 00171, 01314, 01394 Symphonic 00171 Syntax 01610, 01144, 01331 Tatung 01756 TCL 02403, 02429 Technics 00051 Techwood 00051 Teknika 00054, 00150 Telefunken 00702 Toshiba 01524, 00154, 00156, 00650 TVS 00463 Venturer 01865 Videocon 01540, 01541, 02436 Vidikron 00054 Viewsonic 01755, 00864, 00885, 01627, 01742 Viore 01684, 02104, 02352 Vizio 01758, 00864, 00885, 01756 VU 02098 Brand Code No. Wards 00054 Waycon 00156 Westinghouse 01712, 00885, 01577 White Westinghouse 00463, 01661 Wyse 01365 Zenith 00463, 01661 Blu-ray Disc/HD-DVD player/ Lecteur Blu-ray Disc/DVD HD Brand Code No. Sony 11516 Denon 12258 Insignia 10675, 12428, 12596 Integra 11769, 12147 LG 10741 Magnavox 10675 Marantz 12414, 12432 Microsoft 12083 NAD 12572 Olevia 12331 Onkyo 11769, 12147 Oppo 12545 Brand Code No. Panasonic 11641 Philips 12084, 12434 Pioneer 10142, 12442 RCA 11769 Samsung 10199 Sharp 12250 Sylvania 10675 Toshiba 11769 Viore 12553 Vizio 12563 Xbox 12083 Yamaha 12298 TV / Téléviseur Brand Code No. Sony 00810, 00000 Acer 01339 Action 00650 Brand Code No. Midland 00051 Mitsubishi 01250, 00150, 00836 NAD 00156 BPL 01543 Broksonic 00463 Carver 00054 Celebrity 00000 Coby 02306, 02345, 02348 Commercial Solutions 01447 Crosley 00054 Curtis 02352 Curtis Mathes 00054, 00154, 00702, 01661 Daewoo 01661 Digital Lifestyles 01765 Durabrand 00463, 00171 Panasonic 01480, 00051, 00650 PARK 02104 Penney 00156, 00051 Petters 01523 Philco 00054 Philips 01454, 00054, 00690, 01744, 02372 Pioneer 01457, 01260 Polaroid 01523, 01276, 01314, 01687 Portland 01661 Prism 00051 Proscan 01447, 02147, 02256 Proview 01687 If your device is not listed, try the Search function (see “Searching for the correct code”). 2 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 3 Enter the manufacturer’s code (01454). The SET indicator flashes three times and turns off. � Operate the device 1 Aim the RM-VZ220 directly at the device. 2 Press the Device Select button for the device you want to operate. 3 Press POWER to turn on the device. 4 Press buttons on the RM-VZ220 to check that they function. See “Remote Button Descriptions” for the functions of buttons for each device. If the RM-VZ220 does not seem to be working… � Check that you have set the correct manufacturer’s code. � Try repeating the setup procedure using another manufacturer’s code (if listed for your device). If you still cannot operate the RM-VZ220 after trying all the listed codes, try the Search function (see “Searching for the correct code”). Notes � If the setting is incomplete, the SET indicator flashes once and the indicators turn off. Start again from the beginning. � If no operations are performed for 10 seconds while setting, the setting will be canceled, and must be restarted. � To cancel the process, press SET any time. The SET indicator turns off. SET POWER Device Select buttons Number buttons The SET indicator lights up. Searching for the correct code You can set the manufacturer’s code using the Search function. 1 Power on the device with its power switch. 2 Aim the RM-VZ220 at the device you want to set. 3 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 4 Enter 9 - 2 - 2 using the number buttons. The SET indicator flashes three times. 5 Press and hold � to start searching. When the device turns off, release the button. If you overshoot the required code, you can search for the next or previous code using the � or � button. 6 Press . The SET indicator flashes three times and turns off. 7 Check if the code number works correctly (see “Remote Button Descriptions”). If you still cannot operate the device, repeat steps to search for another code that works for most functions of your device. Checking the manufacturer’s code you have set 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 2 Enter 9 - 3 - 3 using the number buttons. The SET indicator flashes three times. 3 Press �. 4 When the SET indicator starts flashing, count the number of flashes. Short flash(es) indicate which digit (first, second, etc.), followed by long flash(es) to indicate the digit number (i.e., 2 long flashes represent the number 2). “0” is indicated by rapid flashing. Determine the 5-digit code number this way. To recheck, press �. 5 Press SET to finish. Clearing the automatic power-on control (Sony devices only) The Device Select buttons are preset to automatically turn on a device when pressed. To cancel the function: 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press , then release both buttons. 2 Enter 9 - 7 - 7 using the number buttons. The SET indicator flashes three times. 3 Press the desired Device Select button. The SET indicator flashes three times and turns off. To set the function again, perform the same procedure above. Restoring the factory settings You can clear all the settings and reset the RM-VZ220 to its factory settings. 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press , then release both buttons. 2 Enter 9 - 0 - 0 using the number buttons. The SET indicator flashes three times. To cancel, press any button except . 3 Press . The SET indicator flashes three times and turns off. Remote Button Descriptions General �� SET: Press to set up the RM-VZ220. The indicator lights or flashes while setting. � Device Select buttons: Press to select the device to operate. � GUIDE: Displays the program guide (EPG). � �/�/�/�/ : Moves the cursor to select a menu item/enters the selected item. � RETURN: Returns to the previous display/exits the menu. � VOL +/–: Turns the volume up/down. � POWER: Turns the selected device on and off. � MUTING: Mutes the volume. Press again to turn muting off. � SLEEP: Enables the Sleep function (when available). The number 5, CH+, and � buttons each have a tactile dot for ease of use. The GUIDE and RETURN buttons do not work for a VCR. Note on the VOL+/– and MUTING buttons When a TV or other video device is selected, the TV’s volume is controlled. When a DVD Home Theater is selected, its volume can be controlled. TV � �: VIDEO 1 input : VIDEO 2 input : HDMI input �: RGB input �: (PIP INPUT) Changes the input mode of the “window” picture. �: (PIP) Turns the “window” picture on and off. �: (PIP MOVE) Moves the location of the “window” picture. �: (PIP STILL) Freezes the “window” picture. �: (PIP SWAP) Switches between “main” and “window” picture. � A: Red button B: Green button C: Yellow button D: Blue button � LIST: (CAPTION) Displays closed captioning. � MENU: Calls up the menu display. � INPUT: Changes the input mode. ��� 1 – 9, 0, ENTER, � (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). � PAGE +/–: (PIP CH +/–) Changes the channel up/down in the “window” picture. � FAVORITES: Enables the Favorite function. � INFO: Displays program information. � OPTIONS: Displays the options menu. � RECALL: Selects the channel previously selected. � CH +/–: Switches the channel up/ down. Cable set top box/IPTV � �: Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). �: Proceeds to the next location. �: Fast reverses. �: Plays. �: Fast forwards. �: Records. �: Pauses. �: Stops. � A, B, C buttons D: (Live TV) Displays Master Guide. � LIST: Displays the title of recorded program. � MENU: Calls up the menu display. � INPUT: Changes the input mode. � � � 1 – 9, 0, ENTER, � (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). � PAGE +/–: Page up/down � FAVORITES: Enables the Favorite function. � INFO: Displays program information. � OPTIONS: Displays the options menu. � RECALL: Switches between the current and previous channel. � CH +/–: Switches the channel up/ down. Satellite receiver � �: Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). �: Proceeds to the next location. �: Fast reverses. �: Plays. �: Fast forwards. �: Records. �: Pauses. �: Stops. � A: Red button B: Green button C: Yellow button D: Blue button � LIST: Displays the title of recorded program/PVR menu. � MENU: Calls up the menu display. � INPUT: (TV/SAT) Switches the output between SAT and TV. � � � 1 – 9, 0, ENTER, � (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). � PAGE +/–: Page up/down � FAVORITES: Enables the Favorite function. � INFO: Displays program information. � OPTIONS: Displays the Satellite dish menu/Station Index. � RECALL: Tunes to the last tuned station. � CH +/–: Switches the channel up/ down. VCR � �: Rewinds. �: Plays. �: Fast forwards. �: Records. �: Pauses. �: Stops. � INPUT: Changes the input mode. � 1 – 9, 0: Number buttons � �: Ejects a tape. � INFO: (DISPLAY) Displays the playback information. � OPTIONS: (ANT/SW) Switches the antenna output. � RECALL: (DRIVE SELECT) Selects the deck. � CH +/–: Switches the channel up/ down. � ENTER: Enters the selected item. DVD player/recorder � �: Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). �: Skips to the next chapter/ track. �: Fast reverses. �: Plays. �: Fast forwards. �: Records (for DVD recorder). �: Pauses. �: Stops. � A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. � LIST: Displays the Title List. � MENU: Displays the DVD menu. � INPUT: Changes the input mode. � 1 – 9, 0: Number buttons � � (dot): (+10) Selects numbers 10 and above. � �: Opens/closes the disc tray. � PAGE +: (DVD) Selects the DVD drive. PAGE –: (HDD) Selects the internal HDD (hard disk drive). � FAVORITES: (TOP MENU) Displays the Top Menu. � INFO: (DISPLAY) Displays the playback information. � OPTIONS: Displays the options menu. � RECALL: (DRIVE SELECT) Switches between HDD and DVD. � CH +/–: Switches the channel up/ down (for DVD recorder). � ENTER: Enters the selected item. Blu-ray Disc/HD-DVD player � �: Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). �: Skips to the next chapter/ track. �: Fast reverses. �: Plays. �: Fast forwards. �: Records (for BD recorder). �: Pauses. �: Stops. � A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. � MENU: Displays the Pop-up Menu/ Disc Menu. � INPUT: Changes the input mode. � 1 – 9, 0: Number buttons � � (dot): (+10) Selects numbers 10 and above. � �: Opens/closes the disc tray. � PAGE +: (BD) Selects the BD drive. PAGE –: (HDD) Selects the internal HDD (hard disk drive). � FAVORITES: (TOP MENU) Displays the Top Menu. � INFO: (DISPLAY) Displays the playback information. � OPTIONS: Displays the options menu. � ENTER: Enters the selected item. DVR (digital video recorder)/PVR (personal video recorder) � �: Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). �: Proceeds to the next location. �: Fast reverses. �: Plays. �: Fast forwards. �: Records. �: Pauses. �: Stops. � A: (REPLAY*) Enables the Replay function for DVR/Replay TV. B: (Live TV*) Displays Master Guide. � LIST: Displays the title of recorded program. � MENU: Calls up the menu display. � INPUT: Changes the input mode. � 1 – 9, 0: Number buttons � � (dot): (+10) Selects numbers 10 and above. � �: Opens/closes the disc tray. � PAGE +/–: Page up/down, Thumbs* up/down � INFO: (DISPLAY) Displays the playback information. � RECALL: Selects the channel previously selected. � CH +/–: Switches the channel up/ down. � ENTER: Enters the selected item. * These buttons correspond to TiVo service or the Replay service. Refer to its instruction manual for details. DVD Home Theater � �: Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). �: Skips to the next chapter/ track. �: Fast reverses. �: Plays. �: Fast forwards. �: Records. �: Pauses. �: Stops. � A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. � LIST: Enables the SOUND FIELD function. � MENU: Displays the DVD menu. � INPUT: Changes the input mode. � 1 – 9, 0: Number buttons � � (dot): (+10) Selects numbers 10 and above. � �: Opens/closes the disc tray. � FAVORITES: (TOP MENU) Displays the Top Menu. � INFO: (DISPLAY) Displays the playback information. � OPTIONS: Displays the amplifier menu. � RECALL: (BAND) Selects FM/AM. � CH +/–: Presets or tunes frequency up/down. � ENTER: Enters the selected item. Notes on using the RM-VZ220 � The RM-VZ220 will not perform functions that the device is not designed for. For example, if your TV does not have the muting function, MUTING on the RM-VZ220 will not function with your TV. � The function of the buttons varies depending on settings/operating modes. The table of “Remote Button Descriptions” shows how the RM-VZ220 generally operates for each device in the preset mode. � If your cable set top box can control volume, be sure to set its volume to a moderate level. If the volume on the cable set top box is turned down completely, you will not be able to adjust your TV’s volume with the RM-VZ220. Manufacturer’s Code List / Liste des codes d’appareil par fabricant English The following tables show brand names (Brand) and their corresponding code numbers (Code No.). 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 2 Enter the manufacturer’s code. The SET indicator flashes three times and turns off. Français Le tableau ci-dessous indique des marques (Brand) et les codes correspondants (Code No.). 1 Maintenez la touche SET enfoncée pendant plus de 3 secondes. L’indicateur SET s’allume. Tout en maintenant la touche SET enfoncée, appuyez sur la touche de sélection d’appareil souhaitée, puis relâchez les deux touches. 2 Saisissez le code d’appareil du fabricant. L’indicateur SET clignote 3 fois, puis s’éteint. TV / Téléviseur Brand Code No. Accurian 10675 Akai 10695 Allegro 10869 Apex Digital 10672, 11056 Bel Canto Design 11571 Broksonic 10695 CineVision 10869 Citizen 10695 CyberHome 11024 Daewoo 10869 Denon 10490, 11634, 12258 Disney 10675, 11270 Emerson 10591, 10675 Enterprise 10591 Funai 10675 GE 10522 GFM 10675 Go Video 10744, 10741, 10869, 11044, 11075 GoldStar 10741 Harman/Kardon 11229 Hitachi 10573, 10664 Hiteker 10672 Insignia 10675, 12428, 12596 Integra 11769, 10627, 12147 JVC 10623, 10867, 11164 Kenwood 10490 LG 10591, 10741, 10869 Magnavox 10503, 10539, 10646, 10675, 11354 Marantz 10539, 12414, 12432 Memorex 10695, 11270, 12213 Microsoft 10522, 12083 Mitsubishi 11521 NAD 10741, 12572 Olevia 12331 Onkyo 10503, 11769, 10627, 11627, 12147 Brand Code No. Oppo 10575, 12545 Panasonic 10490, 11579, 11641 Philco 10675 Philips 10503, 10539, 12056, 12084, 10646, 10675, 11267, 11354, 12434 Pioneer 10142, 10631, 11571, 12442 Polk Audio 10539 Presidian 10675 Proscan 10522 RCA 10522, 11769, 10822, 12213, 12587, 12592, 12594 Rio 10869 Rotel 10623 Samsung 10490, 10573, 10199, 11044, 11075, 12329, 12489 Sansui 10695 Sanyo 10695 Sharp 10630, 10675, 12250 Shinsonic 10533 Sonic Blue 10869 Sony 11633, 10533, 10864, 11033, 11070, 11431, 11516 Sylvania 10675 Symphonic 10675 TCL 12587 Technics 10490 Tivo 11503 Toshiba 10503, 11769, 10695, 11154, 11503, 12006, 12277 Urban Concepts 10503 Viore 12553 Vizio 12563 Vtrek 12587 Xbox 10522, 12083 Yamaha 10490, 10539, 10497, 10817, 12298 Zenith 10503, 10591, 10741, 10869 DVD player / Lecteur DVD Brand Code No. Accurian 10675 Apex Digital 11056 Funai 10675 Go Video 10741 JVC 11164 LG 10741 Magnavox 10646, 10675 Panasonic 10490, 11579 Philips 10646 Brand Code No. Pioneer 10631 RCA 10522 Samsung 10490 Sharp 10675 Sony 11033, 11070, 11431 Sylvania 10675 Toshiba 12277 Zenith 10741 DVD recorder / Enregistreur DVD Brand Code No. Acer 01339 Action 00650 Admiral 00463 Akai 00812, 01675, 00702, 02232 Akira 01733 AOC 01365, 01589 Apex Digital 00748 Aventura 00171 Bell & Howell 00154 BPL 01543 Broksonic 00463 Carver 00054 Celebrity 00000 Coby 02306, 02345, 02348 Commercial Solutions 01447 Crosley 00054 Curtis 02352 Curtis Mathes 00054, 00154, 00702, 01661 Daewoo 01661 Digital Lifestyles 01765 Durabrand 00463, 00171 Dynex 01463, 01810, 02049 Electroband 00000 Electrograph 01755 Electrohome 00463 Elektra 01661 Element 01687 Emerson 01864, 00154, 00463, 00171, 01661, 01394 Emprex 01765 Envision 01365, 01589 ESA 00812, 00171 Fisher 00154 Funai 00171 Gateway 01755, 01756 GE 01447, 00051, 02359 GFM 00171 Haier 01748, 01749, 02309, 02449 Harman/Kardon 00054 Hisense 00748, 01314, 02098 Hitachi 01643, 02215, 02433 iLo 01684 Infinity 00054 Insignia 01564, 00171, 02049 JBL 00054 JCB 00000 JVC 00731, 01253, 01601, 01774 KDS 01687 Kolin 01331 LG 01423, 02358 LXI 00054, 00154, 00156 MAG 01687 Magnavox 01454, 01866, 00054, 01254, 01365, 02372 Marantz 00054 Matsushita 00650 Maxent 01755 Memorex 00154, 00463, 00150 MGA 00150 Midland 00051 Brand Code No. Mitsubishi 01250, 00150, 00836 NAD 00156 NEC 01797 NetTV 01755 Norcent 00748, 01365, 01589 Olevia 01610, 01144, 01331 Onida 01253, 02396 Optimus 00154, 00650 Orion 00463, 01463 Panasonic 01480, 00051, 00650 PARK 02104 Penney 00156, 00051 Petters 01523 Philco 00054 Philips 01454, 00054, 00690, 01744, 02372 Pioneer 01457, 01260 Polaroid 01523, 01276, 01314, 01687 Portland 01661 Prism 00051 Proscan 01447, 02147, 02256 Proview 01687 Quasar 00051, 00650 RadioShack 00154 RCA 01447, 01781, 02187, 02247, 02403, 02429, 02434 Realistic 00154 Sampo 01755 Samsung 00812, 00702 Sansui 00463 Sanyo 00154, 01142 Sceptre 01360, 01599 Scott 01711 Sears 00054, 00154, 00156, 00171 Sharp 00818 Sony 00810, 00000 Spectroniq 01687 Squareview 00171 Superscan 00864 Supreme 00000 SVA 00748 Sylvania 01864, 00054, 00171, 01314, 01394 Symphonic 00171 Syntax 01610, 01144, 01331 Tatung 01756 TCL 02403, 02429 Technics 00051 Techwood 00051 Teknika 00054, 00150 Telefunken 00702 Toshiba 01524, 00154, 00156, 00650 TVS 00463 Venturer 01865 Videocon 01540, 01541, 02436 Vidikron 00054 Viewsonic 01755, 00864, 00885, 01627, 01742 Viore 01684, 02104, 02352 Vizio 01758, 00864, 00885, 01756 VU 02098 Brand Code No. Wards 00054 Waycon 00156 Westinghouse 01712, 00885, 01577 White Westinghouse 00463, 01661 Wyse 01365 Zenith 00463, 01661 Blu-ray Disc/HD-DVD player/ Lecteur Blu-ray Disc/DVD HD Brand Code No. Denon 12258 Insignia 10675, 12428, 12596 Integra 11769, 12147 LG 10741 Magnavox 10675 Marantz 12414, 12432 Microsoft 12083 NAD 12572 Olevia 12331 Onkyo 11769, 12147 Oppo 12545 Panasonic 11641 Brand Code No. Philips 12084, 12434 Pioneer 10142, 12442 RCA 11769 Samsung 10199 Sharp 12250 Sony 11516 Sylvania 10675 Toshiba 11769 Viore 12553 Vizio 12563 Xbox 12083 Yamaha 12298 RM-VZ220_CA [US,FR] 4-170-642-22(1) hree times. searching. release the button. ed code, you can search for the next or previous button. hree times and turns off. works correctly (see “Remote Button he device, repeat steps to search for another nctions of your device. facturer’s code you have set e than 3 seconds. . wn, press the desired Device Select button, mber buttons. hree times. rts flashing, count the number of flashes. ch digit (first, second, etc.), followed by long it number (i.e., 2 long flashes represent the by rapid flashing. number this way. To recheck, press �. atic power-on control (Sony preset to automatically turn on a device when e than 3 seconds. . wn, press , then release both buttons. mber buttons. hree times. lect button. hree times and turns off. form the same procedure above. ry settings nd reset the RM-VZ220 to its factory settings. e than 3 seconds. . wn, press , then release both buttons. mber buttons. hree times. except . hree times and turns off. General �� SET: Press to set up the RM-VZ220. The indicator lights or flashes while setting. � Device Select buttons: Press to select the device to operate. � GUIDE: Displays the program guide (EPG). � �/�/�/�/ : Moves the cursor to select a menu item/enters the selected item. � RETURN: Returns to the previous display/exits the menu. � VOL +/–: Turns the volume up/down. � POWER: Turns the selected device on and off. � MUTING: Mutes the volume. Press again to turn muting off. � SLEEP: Enables the Sleep function (when available). The number 5, CH+, and � buttons each have a tactile dot for ease of use. The GUIDE and RETURN buttons do not work for a VCR. Note on the VOL+/– and MUTING buttons When a TV or other video device is selected, the TV’s volume is controlled. When a DVD Home Theater is selected, its volume can be controlled. TV � �: VIDEO 1 input : VIDEO 2 input : HDMI input �: RGB input �: (PIP INPUT) Changes the input mode of the “window” picture. �: (PIP) Turns the “window” picture on and off. �: (PIP MOVE) Moves the location of the “window” picture. �: (PIP STILL) Freezes the “window” picture. �: (PIP SWAP) Switches between “main” and “window” picture. � A: Red button B: Green button C: Yellow button D: Blue button � LIST: (CAPTION) Displays closed captioning. � MENU: Calls up the menu display. � INPUT: Changes the input mode. ��� 1 – 9, 0, ENTER, � (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). � PAGE +/–: (PIP CH +/–) Changes the channel up/down in the “window” picture. � FAVORITES: Enables the Favorite function. � INFO: Displays program information. � OPTIONS: Displays the options menu. � RECALL: Selects the channel previously selected. � CH +/–: Switches the channel up/ down. �: Pauses. �: Stops. � A, B, C buttons D: (Live TV) Displays Master Guide. � LIST: Displays the title of recorded program. � OPTIONS: Displays the options menu. � RECALL: Switches between the current and previous channel. � CH +/–: Switches the channel up/ down. Satellite receiver � �: Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). �: Proceeds to the next location. �: Fast reverses. �: Plays. �: Fast forwards. �: Records. �: Pauses. �: Stops. � A: Red button B: Green button C: Yellow button D: Blue button � LIST: Displays the title of recorded program/PVR menu. � MENU: Calls up the menu display. � INPUT: (TV/SAT) Switches the output between SAT and TV. � � � 1 – 9, 0, ENTER, � (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). � PAGE +/–: Page up/down � FAVORITES: Enables the Favorite function. � INFO: Displays program information. � OPTIONS: Displays the Satellite dish menu/Station Index. � RECALL: Tunes to the last tuned station. � CH +/–: Switches the channel up/ down. VCR � �: Rewinds. �: Plays. �: Fast forwards. �: Records. �: Pauses. �: Stops. � INPUT: Changes the input mode. � 1 – 9, 0: Number buttons � �: Ejects a tape. � INFO: (DISPLAY) Displays the playback information. � OPTIONS: (ANT/SW) Switches the antenna output. � RECALL: (DRIVE SELECT) Selects the deck. � CH +/–: Switches the channel up/ down. � ENTER: Enters the selected item. DVD player/recorder � �: Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). �: Skips to the next chapter/ track. �: Fast reverses. �: Plays. �: Fast forwards. �: Records (for DVD recorder). �: Pauses. �: Stops. � A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. � LIST: Displays the Title List. � MENU: Displays the DVD menu. � INPUT: Changes the input mode. � 1 – 9, 0: Number buttons � � (dot): (+10) Selects numbers 10 and above. � �: Opens/closes the disc tray. � PAGE +: (DVD) Selects the DVD drive. PAGE –: (HDD) Selects the internal HDD (hard disk drive). � FAVORITES: (TOP MENU) Displays the Top Menu. � INFO: (DISPLAY) Displays the playback information. � OPTIONS: Displays the options menu. � RECALL: (DRIVE SELECT) Switches between HDD and DVD. � CH +/–: Switches the channel up/ down (for DVD recorder). � ENTER: Enters the selected item. �: Records (for BD recorder). �: Pauses. �: Stops. � A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. Displays the Top Menu. � INFO: (DISPLAY) Displays the playback information. � OPTIONS: Displays the options menu. � ENTER: Enters the selected item. DVR (digital video recorder)/PVR (personal video recorder) � �: Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). �: Proceeds to the next location. �: Fast reverses. �: Plays. �: Fast forwards. �: Records. �: Pauses. �: Stops. � A: (REPLAY*) Enables the Replay function for DVR/Replay TV. B: (Live TV*) Displays Master Guide. � LIST: Displays the title of recorded program. � MENU: Calls up the menu display. � INPUT: Changes the input mode. � 1 – 9, 0: Number buttons � � (dot): (+10) Selects numbers 10 and above. � �: Opens/closes the disc tray. � PAGE +/–: Page up/down, Thumbs* up/down � INFO: (DISPLAY) Displays the playback information. � RECALL: Selects the channel previously selected. � CH +/–: Switches the channel up/ down. � ENTER: Enters the selected item. * These buttons correspond to TiVo service or the Replay service. Refer to its instruction manual for details. DVD Home Theater � �: Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). �: Skips to the next chapter/ track. �: Fast reverses. �: Plays. �: Fast forwards. �: Records. �: Pauses. �: Stops. � A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. � LIST: Enables the SOUND FIELD function. � MENU: Displays the DVD menu. � INPUT: Changes the input mode. � 1 – 9, 0: Number buttons � � (dot): (+10) Selects numbers 10 and above. � �: Opens/closes the disc tray. � FAVORITES: (TOP MENU) Displays the Top Menu. � INFO: (DISPLAY) Displays the playback information. � OPTIONS: Displays the amplifier menu. � RECALL: (BAND) Selects FM/AM. � CH +/–: Presets or tunes frequency up/down. � ENTER: Enters the selected item. Notes on using the RM-VZ220 � The RM-VZ220 will not perform functions that the device is not designed for. For example, if your TV does not have the muting function, MUTING on the RM-VZ220 will not function with your TV. � The function of the buttons varies depending on settings/operating modes. The table of “Remote Button Descriptions” shows how the RM-VZ220 generally operates for each device in the preset mode. � If your cable set top box can control volume, be sure to set its volume to a moderate level. If the volume on the cable set top box is turned down completely, you will not be able to adjust your TV’s volume with the RM-VZ220. p g p then release both buttons. 2 Enter the manufacturer’s code. The SET indicator flashes three times and turns off. Français Le tableau ci-dessous indique des marques (Brand) et les codes correspondants (Code No.). 1 Maintenez la touche SET enfoncée pendant plus de 3 secondes. L’indicateur SET s’allume. Tout en maintenant la touche SET enfoncée, appuyez sur la touche de sélection d’appareil souhaitée, puis relâchez les deux touches. 2 Saisissez le code d’appareil du fabricant. L’indicateur SET clignote 3 fois, puis s’éteint. TV / Téléviseur Akai 10695 Allegro 10869 Apex Digital 10672, 11056 Bel Canto Design 11571 Broksonic 10695 CineVision 10869 Citizen 10695 CyberHome 11024 Daewoo 10869 Denon 10490, 11634, 12258 Disney 10675, 11270 Emerson 10591, 10675 Enterprise 10591 Funai 10675 GE 10522 GFM 10675 Go Video 10744, 10741, 10869, 11044, 11075 GoldStar 10741 Harman/Kardon 11229 Hitachi 10573, 10664 Hiteker 10672 Insignia 10675, 12428, 12596 Integra 11769, 10627, 12147 JVC 10623, 10867, 11164 Kenwood 10490 LG 10591, 10741, 10869 Magnavox 10503, 10539, 10646, 10675, 11354 Marantz 10539, 12414, 12432 Memorex 10695, 11270, 12213 Microsoft 10522, 12083 Mitsubishi 11521 NAD 10741, 12572 Olevia 12331 Onkyo 10503, 11769, 10627, 11627, 12147 pp Panasonic 10490, 11579, 11641 Philco 10675 Philips 10503, 10539, 12056, 12084, 10646, 10675, 11267, 11354, 12434 Pioneer 10142, 10631, 11571, 12442 Polk Audio 10539 Presidian 10675 Proscan 10522 RCA 10522, 11769, 10822, 12213, 12587, 12592, 12594 Rio 10869 Rotel 10623 Samsung 10490, 10573, 10199, 11044, 11075, 12329, 12489 Sansui 10695 Sanyo 10695 Sharp 10630, 10675, 12250 Shinsonic 10533 Sonic Blue 10869 Sony 11633, 10533, 10864, 11033, 11070, 11431, 11516 Sylvania 10675 Symphonic 10675 TCL 12587 Technics 10490 Tivo 11503 Toshiba 10503, 11769, 10695, 11154, 11503, 12006, 12277 Urban Concepts 10503 Viore 12553 Vizio 12563 Vtrek 12587 Xbox 10522, 12083 Yamaha 10490, 10539, 10497, 10817, 12298 Zenith 10503, 10591, 10741, 10869 Brand Code No. Accurian 10675 Apex Digital 11056 Funai 10675 Go Video 10741 JVC 11164 LG 10741 Magnavox 10646, 10675 Panasonic 10490, 11579 Philips 10646 Brand Code No. Pioneer 10631 RCA 10522 Samsung 10490 Sharp 10675 Sony 11033, 11070, 11431 Sylvania 10675 Toshiba 12277 Zenith 10741 DVD recorder / Enregistreur DVD Brand Code No. Acer 01339 Action 00650 Admiral 00463 Akai 00812, 01675, 00702, 02232 Akira 01733 AOC 01365, 01589 Apex Digital 00748 Aventura 00171 Bell & Howell 00154 BPL 01543 Broksonic 00463 Carver 00054 Celebrity 00000 Coby 02306, 02345, 02348 Commercial Solutions 01447 Crosley 00054 Curtis 02352 Curtis Mathes 00054, 00154, 00702, 01661 Daewoo 01661 Digital Lifestyles 01765 Durabrand 00463, 00171 Dynex 01463, 01810, 02049 Electroband 00000 Electrograph 01755 Electrohome 00463 Elektra 01661 Element 01687 Emerson 01864, 00154, 00463, 00171, 01661, 01394 Emprex 01765 Envision 01365, 01589 ESA 00812, 00171 Fisher 00154 Funai 00171 Gateway 01755, 01756 GE 01447, 00051, 02359 GFM 00171 Haier 01748, 01749, 02309, 02449 Harman/Kardon 00054 Hisense 00748, 01314, 02098 Hitachi 01643, 02215, 02433 iLo 01684 Infinity 00054 Insignia 01564, 00171, 02049 JBL 00054 JCB 00000 JVC 00731, 01253, 01601, 01774 KDS 01687 Kolin 01331 LG 01423, 02358 LXI 00054, 00154, 00156 MAG 01687 Magnavox 01454, 01866, 00054, 01254, 01365, 02372 Marantz 00054 Matsushita 00650 Maxent 01755 Memorex 00154, 00463, 00150 MGA 00150 Midland 00051 Brand Code No. Mitsubishi 01250, 00150, 00836 NAD 00156 NEC 01797 NetTV 01755 Norcent 00748, 01365, 01589 Olevia 01610, 01144, 01331 Onida 01253, 02396 Optimus 00154, 00650 Orion 00463, 01463 Panasonic 01480, 00051, 00650 PARK 02104 Penney 00156, 00051 Petters 01523 Philco 00054 Philips 01454, 00054, 00690, 01744, 02372 Pioneer 01457, 01260 Polaroid 01523, 01276, 01314, 01687 Portland 01661 Prism 00051 Proscan 01447, 02147, 02256 Proview 01687 Quasar 00051, 00650 RadioShack 00154 RCA 01447, 01781, 02187, 02247, 02403, 02429, 02434 Realistic 00154 Sampo 01755 Samsung 00812, 00702 Sansui 00463 Sanyo 00154, 01142 Sceptre 01360, 01599 Scott 01711 Sears 00054, 00154, 00156, 00171 Sharp 00818 Sony 00810, 00000 Spectroniq 01687 Squareview 00171 Superscan 00864 Supreme 00000 SVA 00748 Sylvania 01864, 00054, 00171, 01314, 01394 Symphonic 00171 Syntax 01610, 01144, 01331 Tatung 01756 TCL 02403, 02429 Technics 00051 Techwood 00051 Teknika 00054, 00150 Telefunken 00702 Toshiba 01524, 00154, 00156, 00650 TVS 00463 Venturer 01865 Videocon 01540, 01541, 02436 Vidikron 00054 Viewsonic 01755, 00864, 00885, 01627, 01742 Viore 01684, 02104, 02352 Vizio 01758, 00864, 00885, 01756 VU 02098 Blu-ray Disc/HD-DVD player/ Lecteur Blu-ray Disc/DVD HD Brand Code No. Denon 12258 Insignia 10675, 12428, 12596 Integra 11769, 12147 LG 10741 Magnavox 10675 Marantz 12414, 12432 Microsoft 12083 NAD 12572 Olevia 12331 Onkyo 11769, 12147 Oppo 12545 Panasonic 11641 Brand Code No. Philips 12084, 12434 Pioneer 10142, 12442 RCA 11769 Samsung 10199 Sharp 12250 Sony 11516 Sylvania 10675 Toshiba 11769 Viore 12553 Vizio 12563 Xbox 12083 Yamaha 12298 RM-VZ220_CA [US,FR] 4-170-642-22(1) hree times and turns off. works correctly (see “Remote Button he device, repeat steps to search for another nctions of your device. facturer’s code you have set e than 3 seconds. . wn, press the desired Device Select button, mber buttons. hree times. rts flashing, count the number of flashes. ch digit (first, second, etc.), followed by long it number (i.e., 2 long flashes represent the by rapid flashing. number this way. To recheck, press �. atic power-on control (Sony preset to automatically turn on a device when e than 3 seconds. . wn, press , then release both buttons. mber buttons. hree times. lect button. hree times and turns off. form the same procedure above. ry settings nd reset the RM-VZ220 to its factory settings. e than 3 seconds. . wn, press , then release both buttons. mber buttons. hree times. except . hree times and turns off. General �� SET: Press to set up the RM-VZ220. The indicator lights or flashes while setting. � Device Select buttons: Press to select the device to operate. � GUIDE: Displays the program guide (EPG). � �/�/�/�/ : Moves the cursor to select a menu item/enters the selected item. � RETURN: Returns to the previous display/exits the menu. � VOL +/–: Turns the volume up/down. � POWER: Turns the selected device on and off. � MUTING: Mutes the volume. Press again to turn muting off. � SLEEP: Enables the Sleep function (when available). The number 5, CH+, and � buttons each have a tactile dot for ease of use. The GUIDE and RETURN buttons do not work for a VCR. Note on the VOL+/– and MUTING buttons When a TV or other video device is selected, the TV’s volume is controlled. When a DVD Home Theater is selected, its volume can be controlled. TV � �: VIDEO 1 input : VIDEO 2 input : HDMI input �: RGB input �: (PIP INPUT) Changes the input mode of the “window” picture. �: (PIP) Turns the “window” picture on and off. �: (PIP MOVE) Moves the location of the “window” picture. �: (PIP STILL) Freezes the “window” picture. �: (PIP SWAP) Switches between “main” and “window” picture. � A: Red button B: Green button C: Yellow button D: Blue button � LIST: (CAPTION) Displays closed captioning. � MENU: Calls up the menu display. � INPUT: Changes the input mode. ��� 1 – 9, 0, ENTER, � (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). � PAGE +/–: (PIP CH +/–) Changes the channel up/down in the “window” picture. � FAVORITES: Enables the Favorite function. � INFO: Displays program information. � OPTIONS: Displays the options menu. � RECALL: Selects the channel previously selected. � CH +/–: Switches the channel up/ down. program. Satellite receiver � �: Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). �: Proceeds to the next location. �: Fast reverses. �: Plays. �: Fast forwards. �: Records. �: Pauses. �: Stops. � A: Red button B: Green button C: Yellow button D: Blue button � LIST: Displays the title of recorded program/PVR menu. � MENU: Calls up the menu display. � INPUT: (TV/SAT) Switches the output between SAT and TV. � � � 1 – 9, 0, ENTER, � (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). � PAGE +/–: Page up/down � FAVORITES: Enables the Favorite function. � INFO: Displays program information. � OPTIONS: Displays the Satellite dish menu/Station Index. � RECALL: Tunes to the last tuned station. � CH +/–: Switches the channel up/ down. VCR � �: Rewinds. �: Plays. �: Fast forwards. �: Records. �: Pauses. �: Stops. � INPUT: Changes the input mode. � 1 – 9, 0: Number buttons � �: Ejects a tape. � INFO: (DISPLAY) Displays the playback information. � OPTIONS: (ANT/SW) Switches the antenna output. � RECALL: (DRIVE SELECT) Selects the deck. � CH +/–: Switches the channel up/ down. � ENTER: Enters the selected item. DVD player/recorder � �: Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). �: Skips to the next chapter/ track. �: Fast reverses. �: Plays. �: Fast forwards. �: Records (for DVD recorder). �: Pauses. �: Stops. � A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. � LIST: Displays the Title List. � MENU: Displays the DVD menu. � INPUT: Changes the input mode. � 1 – 9, 0: Number buttons � � (dot): (+10) Selects numbers 10 and above. � �: Opens/closes the disc tray. � PAGE +: (DVD) Selects the DVD drive. PAGE –: (HDD) Selects the internal HDD (hard disk drive). � FAVORITES: (TOP MENU) Displays the Top Menu. � INFO: (DISPLAY) Displays the playback information. � OPTIONS: Displays the options menu. � RECALL: (DRIVE SELECT) Switches between HDD and DVD. � CH +/–: Switches the channel up/ down (for DVD recorder). � ENTER: Enters the selected item. subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. DVR (digital video recorder)/PVR (personal video recorder) � �: Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). �: Proceeds to the next location. �: Fast reverses. �: Plays. �: Fast forwards. �: Records. �: Pauses. �: Stops. � A: (REPLAY*) Enables the Replay function for DVR/Replay TV. B: (Live TV*) Displays Master Guide. � LIST: Displays the title of recorded program. � MENU: Calls up the menu display. � INPUT: Changes the input mode. � 1 – 9, 0: Number buttons � � (dot): (+10) Selects numbers 10 and above. � �: Opens/closes the disc tray. � PAGE +/–: Page up/down, Thumbs* up/down � INFO: (DISPLAY) Displays the playback information. � RECALL: Selects the channel previously selected. � CH +/–: Switches the channel up/ down. � ENTER: Enters the selected item. * These buttons correspond to TiVo service or the Replay service. Refer to its instruction manual for details. DVD Home Theater � �: Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). �: Skips to the next chapter/ track. �: Fast reverses. �: Plays. �: Fast forwards. �: Records. �: Pauses. �: Stops. � A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. � LIST: Enables the SOUND FIELD function. � MENU: Displays the DVD menu. � INPUT: Changes the input mode. � 1 – 9, 0: Number buttons � � (dot): (+10) Selects numbers 10 and above. � �: Opens/closes the disc tray. � FAVORITES: (TOP MENU) Displays the Top Menu. � INFO: (DISPLAY) Displays the playback information. � OPTIONS: Displays the amplifier menu. � RECALL: (BAND) Selects FM/AM. � CH +/–: Presets or tunes frequency up/down. � ENTER: Enters the selected item. Notes on using the RM-VZ220 � The RM-VZ220 will not perform functions that the device is not designed for. For example, if your TV does not have the muting function, MUTING on the RM-VZ220 will not function with your TV. � The function of the buttons varies depending on settings/operating modes. The table of “Remote Button Descriptions” shows how the RM-VZ220 generally operates for each device in the preset mode. � If your cable set top box can control volume, be sure to set its volume to a moderate level. If the volume on the cable set top box is turned down completely, you will not be able to adjust your TV’s volume with the RM-VZ220. Le tableau ci-dessous indique des marques (Brand) et les codes correspondants (Code No.). 1 Maintenez la touche SET enfoncée pendant plus de 3 secondes. L’indicateur SET s’allume. Tout en maintenant la touche SET enfoncée, appuyez sur la touche de sélection d’appareil souhaitée, puis relâchez les deux touches. 2 Saisissez le code d’appareil du fabricant. L’indicateur SET clignote 3 fois, puis s’éteint. TV / Téléviseur CyberHome 11024 Daewoo 10869 Denon 10490, 11634, 12258 Disney 10675, 11270 Emerson 10591, 10675 Enterprise 10591 Funai 10675 GE 10522 GFM 10675 Go Video 10744, 10741, 10869, 11044, 11075 GoldStar 10741 Harman/Kardon 11229 Hitachi 10573, 10664 Hiteker 10672 Insignia 10675, 12428, 12596 Integra 11769, 10627, 12147 JVC 10623, 10867, 11164 Kenwood 10490 LG 10591, 10741, 10869 Magnavox 10503, 10539, 10646, 10675, 11354 Marantz 10539, 12414, 12432 Memorex 10695, 11270, 12213 Microsoft 10522, 12083 Mitsubishi 11521 NAD 10741, 12572 Olevia 12331 Onkyo 10503, 11769, 10627, 11627, 12147 Presidian 10675 Proscan 10522 RCA 10522, 11769, 10822, 12213, 12587, 12592, 12594 Rio 10869 Rotel 10623 Samsung 10490, 10573, 10199, 11044, 11075, 12329, 12489 Sansui 10695 Sanyo 10695 Sharp 10630, 10675, 12250 Shinsonic 10533 Sonic Blue 10869 Sony 11633, 10533, 10864, 11033, 11070, 11431, 11516 Sylvania 10675 Symphonic 10675 TCL 12587 Technics 10490 Tivo 11503 Toshiba 10503, 11769, 10695, 11154, 11503, 12006, 12277 Urban Concepts 10503 Viore 12553 Vizio 12563 Vtrek 12587 Xbox 10522, 12083 Yamaha 10490, 10539, 10497, 10817, 12298 Zenith 10503, 10591, 10741, 10869 Brand Code No. Accurian 10675 Apex Digital 11056 Funai 10675 Go Video 10741 JVC 11164 LG 10741 Magnavox 10646, 10675 Panasonic 10490, 11579 Philips 10646 Brand Code No. Pioneer 10631 RCA 10522 Samsung 10490 Sharp 10675 Sony 11033, 11070, 11431 Sylvania 10675 Toshiba 12277 Zenith 10741 DVD recorder / Enregistreur DVD Brand Code No. Acer 01339 Action 00650 Admiral 00463 Akai 00812, 01675, 00702, 02232 Akira 01733 AOC 01365, 01589 Apex Digital 00748 Aventura 00171 Bell & Howell 00154 BPL 01543 Broksonic 00463 Carver 00054 Celebrity 00000 Coby 02306, 02345, 02348 Commercial Solutions 01447 Crosley 00054 Curtis 02352 Curtis Mathes 00054, 00154, 00702, 01661 Daewoo 01661 Digital Lifestyles 01765 Durabrand 00463, 00171 Dynex 01463, 01810, 02049 Electroband 00000 Electrograph 01755 Electrohome 00463 Elektra 01661 Element 01687 Emerson 01864, 00154, 00463, 00171, 01661, 01394 Emprex 01765 Envision 01365, 01589 ESA 00812, 00171 Fisher 00154 Funai 00171 Gateway 01755, 01756 GE 01447, 00051, 02359 GFM 00171 Haier 01748, 01749, 02309, 02449 Harman/Kardon 00054 Hisense 00748, 01314, 02098 Hitachi 01643, 02215, 02433 iLo 01684 Infinity 00054 Insignia 01564, 00171, 02049 JBL 00054 JCB 00000 JVC 00731, 01253, 01601, 01774 KDS 01687 Kolin 01331 LG 01423, 02358 LXI 00054, 00154, 00156 MAG 01687 Magnavox 01454, 01866, 00054, 01254, 01365, 02372 Marantz 00054 Matsushita 00650 Maxent 01755 Memorex 00154, 00463, 00150 MGA 00150 Midland 00051 Brand Code No. Mitsubishi 01250, 00150, 00836 NAD 00156 NEC 01797 NetTV 01755 Norcent 00748, 01365, 01589 Olevia 01610, 01144, 01331 Onida 01253, 02396 Optimus 00154, 00650 Orion 00463, 01463 Panasonic 01480, 00051, 00650 PARK 02104 Penney 00156, 00051 Petters 01523 Philco 00054 Philips 01454, 00054, 00690, 01744, 02372 Pioneer 01457, 01260 Polaroid 01523, 01276, 01314, 01687 Portland 01661 Prism 00051 Proscan 01447, 02147, 02256 Proview 01687 Quasar 00051, 00650 RadioShack 00154 RCA 01447, 01781, 02187, 02247, 02403, 02429, 02434 Realistic 00154 Sampo 01755 Samsung 00812, 00702 Sansui 00463 Sanyo 00154, 01142 Sceptre 01360, 01599 Scott 01711 Sears 00054, 00154, 00156, 00171 Sharp 00818 Sony 00810, 00000 Spectroniq 01687 Squareview 00171 Superscan 00864 Supreme 00000 SVA 00748 Sylvania 01864, 00054, 00171, 01314, 01394 Symphonic 00171 Syntax 01610, 01144, 01331 Tatung 01756 TCL 02403, 02429 Technics 00051 Techwood 00051 Teknika 00054, 00150 Telefunken 00702 Toshiba 01524, 00154, 00156, 00650 TVS 00463 Venturer 01865 Videocon 01540, 01541, 02436 Vidikron 00054 Viewsonic 01755, 00864, 00885, 01627, 01742 Viore 01684, 02104, 02352 Vizio 01758, 00864, 00885, 01756 VU 02098 Blu-ray Disc/HD-DVD player/ Lecteur Blu-ray Disc/DVD HD Brand Code No. Denon 12258 Insignia 10675, 12428, 12596 Integra 11769, 12147 LG 10741 Magnavox 10675 Marantz 12414, 12432 Microsoft 12083 NAD 12572 Olevia 12331 Onkyo 11769, 12147 Oppo 12545 Panasonic 11641 Brand Code No. Philips 12084, 12434 Pioneer 10142, 12442 RCA 11769 Samsung 10199 Sharp 12250 Sony 11516 Sylvania 10675 Toshiba 11769 Viore 12553 Vizio 12563 Xbox 12083 Yamaha 12298 If your device is not listed, try the Search function (see “Searching for the correct code”). 2 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 3 Enter the manufacturer’s code (01454). The SET indicator flashes three times and turns off.  Operate the device 1 Aim the RM-VZ220 directly at the device. 2 Press the Device Select button for the device you want to operate. 3 Press POWER to turn on the device. 4 Press buttons on the RM-VZ220 to check that they function. See “Remote Button Descriptions” for the functions of buttons for each device. If the RM-VZ220 does not seem to be working… �Check that you have set the correct manufacturer’s code. �Try repeating the setup procedure using another manufacturer’s code (if listed for your device). If you still cannot operate the RM-VZ220 after trying all the listed codes, try the Search function (see “Searching for the correct code”). Notes �If the setting is incomplete, the SET indicator flashes once and the indicators turn off. Start again from the beginning. �If no operations are performed for 10 seconds while setting, the setting will be canceled, and must be restarted. �To cancel the process, press SET any time. The SET indicator turns off. SET POWER Device Select buttons Number buttons The SET indicator lights up. Searching for the correct code You can set the manufacturer’s code using the Search function. 1 Power on the device with its power switch. 2 Aim the RM-VZ220 at the device you want to set. 3 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 4 Enter 9 - 2 - 2 using the number buttons. The SET indicator flashes three times. 5 Press and hold  to start searching. When the device turns off, release the button. If you overshoot the required code, you can search for the next or previous code using the  or  button. 6 Press . The SET indicator flashes three times and turns off. 7 Check if the code number works correctly (see “Remote Button Descriptions”). If you still cannot operate the device, repeat steps to search for another code that works for most functions of your device. Checking the manufacturer’s code you have set 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 2 Enter 9 - 3 - 3 using the number buttons. The SET indicator flashes three times. 3 Press . 4 When the SET indicator starts flashing, count the number of flashes. Short flash(es) indicate which digit (first, second, etc.), followed by long flash(es) to indicate the digit number (i.e., 2 long flashes represent the number 2). “0” is indicated by rapid flashing. Determine the 5-digit code number this way. To recheck, press . 5 Press SET to finish. Clearing the automatic power-on control (Sony devices only) The Device Select buttons are preset to automatically turn on a device when pressed. To cancel the function: 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press , then release both buttons. 2 Enter 9 - 7 - 7 using the number buttons. The SET indicator flashes three times. 3 Press the desired Device Select button. The SET indicator flashes three times and turns off. To set the function again, perform the same procedure above. Restoring the factory settings You can clear all the settings and reset the RM-VZ220 to its factory settings. 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press , then release both buttons. 2 Enter 9 - 0 - 0 using the number buttons. The SET indicator flashes three times. To cancel, press any button except . 3 Press . The SET indicator flashes three times and turns off. Remote Button Descriptions General �SET: Press to set up the RM-VZ220. The indicator lights or flashes while setting. �Device Select buttons: Press to select the device to operate. �GUIDE: Displays the program guide (EPG). �//// : Moves the cursor to select a menu item/enters the selected item. �RETURN: Returns to the previous display/exits the menu. �VOL +/–: Turns the volume up/down. �POWER: Turns the selected device on and off. �MUTING: Mutes the volume. Press again to turn muting off. �SLEEP: Enables the Sleep function (when available). The number 5, CH+, and  buttons each have a tactile dot for ease of use. The GUIDE and RETURN buttons do not work for a VCR. Note on the VOL+/– and MUTING buttons When a TV or other video device is selected, the TV’s volume is controlled. When a DVD Home Theater is selected, its volume can be controlled. TV �: VIDEO 1 input : VIDEO 2 input : HDMI input : RGB input : (PIP INPUT) Changes the input mode of the “window” picture. : (PIP) Turns the “window” picture on and off. : (PIP MOVE) Moves the location of the “window” picture. : (PIP STILL) Freezes the “window” picture. : (PIP SWAP) Switches between “main” and “window” picture. �A: Red button B: Green button C: Yellow button D: Blue button �LIST: (CAPTION) Displays closed captioning. �MENU: Calls up the menu display. �INPUT: Changes the input mode.  1 – 9, 0, ENTER,  (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). �PAGE +/–: (PIP CH +/–) Changes the channel up/down in the “window” picture. �FAVORITES: Enables the Favorite function. �INFO: Displays program information. �OPTIONS: Displays the options menu. �RECALL: Selects the channel previously selected. �CH +/–: Switches the channel up/ down. Cable set top box/IPTV �: Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). : Proceeds to the next location. : Fast reverses. : Plays. : Fast forwards. : Records. : Pauses. : Stops. �A, B, C buttons D: (Live TV) Displays Master Guide. �LIST: Displays the title of recorded program. �MENU: Calls up the menu display. �INPUT: Changes the input mode. �  1 – 9, 0, ENTER,  (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). �PAGE +/–: Page up/down �FAVORITES: Enables the Favorite function. �INFO: Displays program information. �OPTIONS: Displays the options menu. �RECALL: Switches between the current and previous channel. �CH +/–: Switches the channel up/ down. Satellite receiver �: Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). : Proceeds to the next location. : Fast reverses. : Plays. : Fast forwards. : Records. : Pauses. : Stops. �A: Red button B: Green button C: Yellow button D: Blue button �LIST: Displays the title of recorded program/PVR menu. �MENU: Calls up the menu display. �INPUT: (TV/SAT) Switches the output between SAT and TV. �  1 – 9, 0, ENTER,  (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). �PAGE +/–: Page up/down �FAVORITES: Enables the Favorite function. �INFO: Displays program information. �OPTIONS: Displays the Satellite dish menu/Station Index. �RECALL: Tunes to the last tuned station. �CH +/–: Switches the channel up/ down. VCR �: Rewinds. : Plays. : Fast forwards. : Records. : Pauses. : Stops. �INPUT: Changes the input mode. �1 – 9, 0: Number buttons �: Ejects a tape. �INFO: (DISPLAY) Displays the playback information. �OPTIONS: (ANT/SW) Switches the antenna output. �RECALL: (DRIVE SELECT) Selects the deck. �CH +/–: Switches the channel up/ down. �ENTER: Enters the selected item. DVD player/recorder �: Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). : Skips to the next chapter/ track. : Fast reverses. : Plays. : Fast forwards. : Records (for DVD recorder). : Pauses. : Stops. �A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. �LIST: Displays the Title List. �MENU: Displays the DVD menu. �INPUT: Changes the input mode. �1 – 9, 0: Number buttons � (dot): (+10) Selects numbers 10 and above. �: Opens/closes the disc tray. �PAGE +: (DVD) Selects the DVD drive. � PAGE –: (HDD) Selects the internal HDD (hard disk drive). �FAVORITES: (TOP MENU) Displays the Top Menu. �INFO: (DISPLAY) Displays the playback information. �OPTIONS: Displays the options menu. �RECALL: (DRIVE SELECT) Switches between HDD and DVD. �CH +/–: Switches the channel up/ down (for DVD recorder). �ENTER: Enters the selected item. Blu-ray Disc/HD-DVD player �: Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). : Skips to the next chapter/ track. : Fast reverses. : Plays. : Fast forwards. : Records (for BD recorder). : Pauses. : Stops. �A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. �MENU: Displays the Pop-up Menu/ Disc Menu. �INPUT: Changes the input mode. �1 – 9, 0: Number buttons � (dot): (+10) Selects numbers 10 and above. �: Opens/closes the disc tray. �PAGE +: (BD) Selects the BD drive. � PAGE –: (HDD) Selects the internal HDD (hard disk drive). �FAVORITES: (TOP MENU) Displays the Top Menu. �INFO: (DISPLAY) Displays the playback information. �OPTIONS: Displays the options menu. �ENTER: Enters the selected item. DVR (digital video recorder)/PVR (personal video recorder) �: Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). : Proceeds to the next location. : Fast reverses. : Plays. : Fast forwards. : Records. : Pauses. : Stops. �A: (REPLAY*) Enables the Replay function for DVR/Replay TV. � B: (Live TV*) Displays Master Guide. �LIST: Displays the title of recorded program. �MENU: Calls up the menu display. �INPUT: Changes the input mode. �1 – 9, 0: Number buttons � (dot): (+10) Selects numbers 10 and above. �: Opens/closes the disc tray. �PAGE +/–: Page up/down, Thumbs* up/down �INFO: (DISPLAY) Displays the playback information. �RECALL: Selects the channel previously selected. �CH +/–: Switches the channel up/ down. �ENTER: Enters the selected item. * These buttons correspond to TiVo service or the Replay service. Refer to its instruction manual for details. DVD Home Theater �: Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). : Skips to the next chapter/ track. : Fast reverses. : Plays. : Fast forwards. : Records. : Pauses. : Stops. �A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. �LIST: Enables the SOUND FIELD function. �MENU: Displays the DVD menu. �INPUT: Changes the input mode. �1 – 9, 0: Number buttons � (dot): (+10) Selects numbers 10 and above. �: Opens/closes the disc tray. �FAVORITES: (TOP MENU) Displays the Top Menu. �INFO: (DISPLAY) Displays the playback information. �OPTIONS: Displays the amplifier menu. �RECALL: (BAND) Selects FM/AM. �CH +/–: Presets or tunes frequency up/down. �ENTER: Enters the selected item. Notes on using the RM-VZ220 �The RM-VZ220 will not perform functions that the device is not designed for. For example, if your TV does not have the muting function, MUTING on the RM-VZ220 will not function with your TV. �The function of the buttons varies depending on settings/operating modes. The table of “Remote Button Descriptions” shows how the RM-VZ220 generally operates for each device in the preset mode. �If your cable set top box can control volume, be sure to set its volume to a moderate level. If the volume on the cable set top box is turned down completely, you will not be able to adjust your TV’s volume with the RM-VZ220. Manufacturer’s Code List / Liste des codes d’appareil par fabricant English The following tables show brand names (Brand) and their corresponding code numbers (Code No.). 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 2 Enter the manufacturer’s code. The SET indicator flashes three times and turns off. Français Le tableau ci-dessous indique des marques (Brand) et les codes correspondants (Code No.). 1 Maintenez la touche SET enfoncée pendant plus de 3 secondes. L’indicateur SET s’allume. Tout en maintenant la touche SET enfoncée, appuyez sur la touche de sélection d’appareil souhaitée, puis relâchez les deux touches. 2 Saisissez le code d’appareil du fabricant. L’indicateur SET clignote 3 fois, puis s’éteint. TV / Téléviseur Brand Code No. Accurian 10675 Akai 10695 Allegro 10869 Apex Digital 10672, 11056 Bel Canto Design 11571 Broksonic 10695 CineVision 10869 Citizen 10695 CyberHome 11024 Daewoo 10869 Denon 10490, 11634, 12258 Disney 10675, 11270 Emerson 10591, 10675 Enterprise 10591 Funai 10675 GE 10522 GFM 10675 Go Video 10744, 10741, 10869, 11044, 11075 GoldStar 10741 Harman/Kardon 11229 Hitachi 10573, 10664 Hiteker 10672 Insignia 10675, 12428, 12596 Integra 11769, 10627, 12147 JVC 10623, 10867, 11164 Kenwood 10490 LG 10591, 10741, 10869 Magnavox 10503, 10539, 10646, 10675, 11354 Marantz 10539, 12414, 12432 Memorex 10695, 11270, 12213 Microsoft 10522, 12083 Mitsubishi 11521 NAD 10741, 12572 Olevia 12331 Onkyo 10503, 11769, 10627, 11627, 12147 Brand Code No. Oppo 10575, 12545 Panasonic 10490, 11579, 11641 Philco 10675 Philips 10503, 10539, 12056, 12084, 10646, 10675, 11267, 11354, 12434 Pioneer 10142, 10631, 11571, 12442 Polk Audio 10539 Presidian 10675 Proscan 10522 RCA 10522, 11769, 10822, 12213, 12587, 12592, 12594 Rio 10869 Rotel 10623 Samsung 10490, 10573, 10199, 11044, 11075, 12329, 12489 Sansui 10695 Sanyo 10695 Sharp 10630, 10675, 12250 Shinsonic 10533 Sonic Blue 10869 Sony 11633, 10533, 10864, 11033, 11070, 11431, 11516 Sylvania 10675 Symphonic 10675 TCL 12587 Technics 10490 Tivo 11503 Toshiba 10503, 11769, 10695, 11154, 11503, 12006, 12277 Urban Concepts 10503 Viore 12553 Vizio 12563 Vtrek 12587 Xbox 10522, 12083 Yamaha 10490, 10539, 10497, 10817, 12298 Zenith 10503, 10591, 10741, 10869 DVD player / Lecteur DVD Brand Code No. Accurian 10675 Apex Digital 11056 Funai 10675 Go Video 10741 JVC 11164 LG 10741 Magnavox 10646, 10675 Panasonic 10490, 11579 Philips 10646 Brand Code No. Pioneer 10631 RCA 10522 Samsung 10490 Sharp 10675 Sony 11033, 11070, 11431 Sylvania 10675 Toshiba 12277 Zenith 10741 DVD recorder / Enregistreur DVD Brand Code No. Acer 01339 Action 00650 Admiral 00463 Akai 00812, 01675, 00702, 02232 Akira 01733 AOC 01365, 01589 Apex Digital 00748 Aventura 00171 Bell & Howell 00154 BPL 01543 Broksonic 00463 Carver 00054 Celebrity 00000 Coby 02306, 02345, 02348 Commercial Solutions 01447 Crosley 00054 Curtis 02352 Curtis Mathes 00054, 00154, 00702, 01661 Daewoo 01661 Digital Lifestyles 01765 Durabrand 00463, 00171 Dynex 01463, 01810, 02049 Electroband 00000 Electrograph 01755 Electrohome 00463 Elektra 01661 Element 01687 Emerson 01864, 00154, 00463, 00171, 01661, 01394 Emprex 01765 Envision 01365, 01589 ESA 00812, 00171 Fisher 00154 Funai 00171 Gateway 01755, 01756 GE 01447, 00051, 02359 GFM 00171 Haier 01748, 01749, 02309, 02449 Harman/Kardon 00054 Hisense 00748, 01314, 02098 Hitachi 01643, 02215, 02433 iLo 01684 Infinity 00054 Insignia 01564, 00171, 02049 JBL 00054 JCB 00000 JVC 00731, 01253, 01601, 01774 KDS 01687 Kolin 01331 LG 01423, 02358 LXI 00054, 00154, 00156 MAG 01687 Magnavox 01454, 01866, 00054, 01254, 01365, 02372 Marantz 00054 Matsushita 00650 Maxent 01755 Memorex 00154, 00463, 00150 MGA 00150 Midland 00051 Brand Code No. Mitsubishi 01250, 00150, 00836 NAD 00156 NEC 01797 NetTV 01755 Norcent 00748, 01365, 01589 Olevia 01610, 01144, 01331 Onida 01253, 02396 Optimus 00154, 00650 Orion 00463, 01463 Panasonic 01480, 00051, 00650 PARK 02104 Penney 00156, 00051 Petters 01523 Philco 00054 Philips 01454, 00054, 00690, 01744, 02372 Pioneer 01457, 01260 Polaroid 01523, 01276, 01314, 01687 Portland 01661 Prism 00051 Proscan 01447, 02147, 02256 Proview 01687 Quasar 00051, 00650 RadioShack 00154 RCA 01447, 01781, 02187, 02247, 02403, 02429, 02434 Realistic 00154 Sampo 01755 Samsung 00812, 00702 Sansui 00463 Sanyo 00154, 01142 Sceptre 01360, 01599 Scott 01711 Sears 00054, 00154, 00156, 00171 Sharp 00818 Sony 00810, 00000 Spectroniq 01687 Squareview 00171 Superscan 00864 Supreme 00000 SVA 00748 Sylvania 01864, 00054, 00171, 01314, 01394 Symphonic 00171 Syntax 01610, 01144, 01331 Tatung 01756 TCL 02403, 02429 Technics 00051 Techwood 00051 Teknika 00054, 00150 Telefunken 00702 Toshiba 01524, 00154, 00156, 00650 TVS 00463 Venturer 01865 Videocon 01540, 01541, 02436 Vidikron 00054 Viewsonic 01755, 00864, 00885, 01627, 01742 Viore 01684, 02104, 02352 Vizio 01758, 00864, 00885, 01756 VU 02098 Brand Code No. Wards 00054 Waycon 00156 Westinghouse 01712, 00885, 01577 White Westinghouse 00463, 01661 Wyse 01365 Zenith 00463, 01661 Blu-ray Disc/HD-DVD player/ Lecteur Blu-ray Disc/DVD HD Brand Code No. Denon 12258 Insignia 10675, 12428, 12596 Integra 11769, 12147 LG 10741 Magnavox 10675 Marantz 12414, 12432 Microsoft 12083 NAD 12572 Olevia 12331 Onkyo 11769, 12147 Oppo 12545 Panasonic 11641 Brand Code No. Philips 12084, 12434 Pioneer 10142, 12442 RCA 11769 Samsung 10199 Sharp 12250 Sony 11516 Sylvania 10675 Toshiba 11769 Viore 12553 Vizio 12563 Xbox 12083 Yamaha 12298

4-170-642-12(1) Remote Commander RM-VZ220 ©2010 Sony Corporation Printed in China Operating Instructions Manual de instrucciones (parte posterior) English For the Customers in the U.S.A. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Setting Up the RM-VZ220 The RM-VZ220 is preset at the factory to operate Sony brand video devices set to any of the Device Select buttons (see the table below). To use with non-Sony devices, or Sony devices that are not preset at the factory, set the manufacturer’s code for each device. Devices Button Factory setting* TV TV Sony TV (00810) TV, Cable set top box, Satellite receiver, IPTV, DVD player, DVD recorder, Blu-ray Disc player, DVR (digital video recorder), PVR (personal video recorder), VCR, DVD Home Theater CBL (SAT) Cable set top box (non- Sony) (51376) VCR Sony VCR (60032) DVD Sony DVD player (11033) * The five-digit code is the preset manufacturer’s code. Note Only a TV can be assigned to the TV Device Select button. You can assign any device to the other Device Select buttons. Installing the batteries Slide open the battery compartment and insert two size AA (R6) dry batteries (not supplied). Insert the batteries (negative end first) through the guide clamp within each compartment as shown below. 1 2 Battery life Under normal conditions, size AA (LR6) alkaline batteries will last up to one year. If the RM-VZ220 does not operate properly, the batteries might be drained. Replace both batteries with new ones. Notes  Replace the batteries within 2 minutes after removing them, and do not press any button when replacing the batteries. Otherwise, your code settings may be cleared.  Do not use an old battery with a new one, or mix different types of batteries together.  If the electrolyte inside the battery should leak, wipe the contaminated area of the battery compartment with a cloth and replace the old batteries with new ones. To prevent electrolyte from leaking, remove the batteries when you plan not to use the RM-VZ220 for a long period of time. Specifications Operating distance Approx. 11 m (36 ft) (varies depending on devices of different manufacturers) Power requirements Two size AA (R6) dry batteries (not supplied) Battery life Approx. 1 year when using size AA (LR6) alkaline batteries (varies depending on frequency of button use - up to approx. 300 times per day.) Dimensions Approx. 53 × 213 × 27 mm (2 1/8 × 8 1/2 × 1 1/8 in.) (w/h/d) Mass Approx. 100 g (3.5 oz) (not including batteries) Design and specifications are subject to change without notice. Troubleshooting If you have problems setting up or using the RM-VZ220:  Carefully perform the setup procedure of “Startup Guide.” If the RM-VZ220 does not work, try repeating the setup procedure using another manufacturer’s code (if listed for your device). If you still cannot operate the RM-VZ220, try the Search function (see “Searching for the correct code”).  Aim the RM-VZ220 directly at the device.  Remove any obstacles in the path between the RM-VZ220 and the device.  Make sure you have pressed the correct Device Select button.  Check that the device has infrared remote capability. For example, if your device did not come with a remote control, it probably is not capable of being controlled by the RM-VZ220.  The batteries are weak, or not inserted correctly. Replace them with new ones or insert them correctly. For the customers in the U.S.A. Customer Support Information After you have read through this manual, if you still cannot get the RM-VZ220 to work properly, call the Sony Customer Support Helpline at 1-800-822-2217. Startup Guide This guide shows you how to set up and use the RM-VZ220 to operate your devices. If your Sony device has already been preset, see “Operate the device.” Set the manufacturer’s code Example: To set up a Philips TV 1 Find the manufacturer’s code in “Manufacturer’s Code List.” RM-VZ220_U [US,ES] 4-170-642-12(1) RM-VZ220_U [US,ES] 4-170-642-12(1) 4-170-642-12(1) Remote Commander RM-VZ220 ©2010 Sony Corporation Printed in China Operating Instructions Manual de instrucciones (parte posterior) English For the Customers in the U.S.A. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ˎ Reorient or relocate the receiving antenna. ˎ Increase the separation between the equipment and receiver. ˎ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ˎ Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Setting Up the RM-VZ220 The RM-VZ220 is preset at the factory to operate Sony brand video devices set to any of the Device Select buttons (see the table below). To use with non-Sony devices, or Sony devices that are not preset at the factory, set the manufacturer’s code for each device. Devices Button Factory setting* TV TV Sony TV (00810) TV, Cable set top box, Satellite receiver, IPTV, DVD player, DVD recorder, Blu-ray Disc player, DVR (digital video recorder), PVR (personal video recorder), VCR, DVD Home Theater CBL (SAT) Cable set top box (non- Sony) (51376) VCR Sony VCR (60032) DVD Sony DVD player (11033) * The five-digit code is the preset manufacturer’s code. Note Only a TV can be assigned to the TV Device Select button. You can assign any device to the other Device Select buttons. Installing the batteries Slide open the battery compartment and insert two size AA (R6) dry batteries (not supplied). Insert the batteries (negative end first) through the guide clamp within each compartment as shown below. 1 2 Battery life Under normal conditions, size AA (LR6) alkaline batteries will last up to one year. If the RM-VZ220 does not operate properly, the batteries might be drained. Replace both batteries with new ones. Notes ˎ Replace the batteries within 2 minutes after removing them, and do not press any button when replacing the batteries. Otherwise, your code settings may be cleared. ˎ Do not use an old battery with a new one, or mix different types of batteries together. ˎ If the electrolyte inside the battery should leak, wipe the contaminated area of the battery compartment with a cloth and replace the old batteries with new ones. To prevent electrolyte from leaking, remove the batteries when you plan not to use the RM-VZ220 for a long period of time. Specifications Operating distance Approx. 11 m (36 ft) (varies depending on devices of different manufacturers) Power requirements Two size AA (R6) dry batteries (not supplied) Battery life Approx. 1 year when using size AA (LR6) alkaline batteries (varies depending on frequency of button use - up to approx. 300 times per day.) Dimensions Approx. 53 × 213 × 27 mm (2 1/8 × 8 1/2 × 1 1/8 in.) (w/h/d) Mass Approx. 100 g (3.5 oz) (not including batteries) Design and specifications are subject to change without notice. Troubleshooting If you have problems setting up or using the RM-VZ220: ˎ Carefully perform the setup procedure of “Startup Guide.” If the RM-VZ220 does not work, try repeating the setup procedure using another manufacturer’s code (if listed for your device). If you still cannot operate the RM-VZ220, try the Search function (see “Searching for the correct code”). ˎ Aim the RM-VZ220 directly at the device. ˎ Remove any obstacles in the path between the RM-VZ220 and the device. ˎ Make sure you have pressed the correct Device Select button. ˎ Check that the device has infrared remote capability. For example, if your device did not come with a remote control, it probably is not capable of being controlled by the RM-VZ220. ˎ The batteries are weak, or not inserted correctly. Replace them with new ones or insert them correctly. For the customers in the U.S.A. Customer Support Information After you have read through this manual, if you still cannot get the RM-VZ220 to work properly, call the Sony Customer Support Helpline at 1-800-822-2217. Startup Guide This guide shows you how to set up and use the RM-VZ220 to operate your devices. If your Sony device has already been preset, see “Operate the device.” Set the manufacturer’s code Example: To set up a Philips TV 1 Find the manufacturer’s code in “Manufacturer’s Code List.” Manufacturer’s Code List / Lista de códigos del fabricante English The following tables show brand names (Brand) and their corresponding code numbers (Code No.). 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 2 Enter the manufacturer’s code. The SET indicator flashes three times and turns off. Español La siguiente tabla muestra los nombres de las marcas (Brand) y el número de código correspondiente (Code No.). 1 Presione y mantenga presionado el botón SET durante más de 3 segundos. Se encenderá la luz indicadora SET. Mientras tiene presionado el botón SET, presione el botón de selección de dispositivo deseado y luego suelte ambos botones. 2 Ingrese el código del fabricante. El indicador SET parpadeará tres veces y se apagará. Brand Code No. Sony 00810, 00000 Acer 01339 Action 00650 Admiral 00463 Akai 00812, 01675, 00702, 02232 Akira 01733 AOC 01365, 01589 Apex Digital 00748 Aventura 00171 Bell & Howell 00154 BPL 01543 Broksonic 00463 Carver 00054 Celebrity 00000 Coby 02306, 02345, 02348 Commercial Solutions 01447 Crosley 00054 Curtis 02352 Curtis Mathes 00054, 00154, 00702, 01661 Daewoo 01661 Digital Lifestyles 01765 Durabrand 00463, 00171 Dynex 01463, 01810, 02049 Electroband 00000 Electrograph 01755 Electrohome 00463 Elektra 01661 Element 01687 Emerson 01864, 00154, 00463, 00171, 01661, 01394 Emprex 01765 Envision 01365, 01589 ESA 00812, 00171 Fisher 00154 Funai 00171 Gateway 01755, 01756 GE 01447, 00051, 02359 GFM 00171 Haier 01748, 01749, 02309, 02449 Harman/Kardon 00054 Hisense 00748, 01314, 02098 Hitachi 01643, 02215, 02433 iLo 01684 Infinity 00054 Insignia 01564, 00171, 02049 JBL 00054 JCB 00000 JVC 00731, 01253, 01601, 01774 KDS 01687 Kolin 01331 LG 01423, 02358 LXI 00054, 00154, 00156 MAG 01687 Magnavox 01454, 01866, 00054, 01254, 01365, 02372 Marantz 00054 Matsushita 00650 Maxent 01755 Memorex 00154, 00463, 00150 MGA 00150 Brand Code No. Midland 00051 Mitsubishi 01250, 00150, 00836 NAD 00156 NEC 01797 NetTV 01755 Norcent 00748, 01365, 01589 Olevia 01610, 01144, 01331 Onida 01253, 02396 Optimus 00154, 00650 Orion 00463, 01463 Panasonic 01480, 00051, 00650 PARK 02104 Penney 00156, 00051 Petters 01523 Philco 00054 Philips 01454, 00054, 00690, 01744, 02372 Pioneer 01457, 01260 Polaroid 01523, 01276, 01314, 01687 Portland 01661 Prism 00051 Proscan 01447, 02147, 02256 Proview 01687 Quasar 00051, 00650 RadioShack 00154 RCA 01447, 01781, 02187, 02247, 02403, 02429, 02434 Realistic 00154 Sampo 01755 Samsung 00812, 00702 Sansui 00463 Sanyo 00154, 01142 Sceptre 01360, 01599 Scott 01711 Sears 00054, 00154, 00156, 00171 Sharp 00818 Spectroniq 01687 Squareview 00171 Superscan 00864 Supreme 00000 SVA 00748 Sylvania 01864, 00054, 00171, 01314, 01394 Symphonic 00171 Syntax 01610, 01144, 01331 Tatung 01756 TCL 02403, 02429 Technics 00051 Techwood 00051 Teknika 00054, 00150 Telefunken 00702 Toshiba 01524, 00154, 00156, 00650 TVS 00463 Venturer 01865 Videocon 01540, 01541, 02436 Vidikron 00054 Viewsonic 01755, 00864, 00885, 01627, 01742 Viore 01684, 02104, 02352 Vizio 01758, 00864, 00885, 01756 VU 02098 TV / TV Brand Code No. Wards 00054 Waycon 00156 Westinghouse 01712, 00885, 01577 White Westinghouse 00463, 01661 Wyse 01365 Zenith 00463, 01661 Brand Code No. Sony 11633, 10533, 10864, 11033, 11070, 11431, 11516 Accurian 10675 Akai 10695 Allegro 10869 Apex Digital 10672, 11056 Bel Canto Design 11571 Broksonic 10695 CineVision 10869 Citizen 10695 CyberHome 11024 Daewoo 10869 Denon 10490, 11634, 12258 Disney 10675, 11270 Emerson 10591, 10675 Enterprise 10591 Funai 10675 GE 10522 GFM 10675 Go Video 10744, 10741, 10869, 11044, 11075 GoldStar 10741 Harman/Kardon 11229 Hitachi 10573, 10664 Hiteker 10672 Insignia 10675, 12428, 12596 Integra 11769, 10627, 12147 JVC 10623, 10867, 11164 Kenwood 10490 LG 10591, 10741, 10869 Magnavox 10503, 10539, 10646, 10675, 11354 Marantz 10539, 12414, 12432 Memorex 10695, 11270, 12213 Microsoft 10522, 12083 Mitsubishi 11521 NAD 10741, 12572 Olevia 12331 Brand Code No. Onkyo 10503, 11769, 10627, 11627, 12147 Oppo 10575, 12545 Panasonic 10490, 11579, 11641 Philco 10675 Philips 10503, 10539, 12056, 12084, 10646, 10675, 11267, 11354, 12434 Pioneer 10142, 10631, 11571, 12442 Polk Audio 10539 Presidian 10675 Proscan 10522 RCA 10522, 11769, 10822, 12213, 12587, 12592, 12594 Rio 10869 Rotel 10623 Samsung 10490, 10573, 10199, 11044, 11075, 12329, 12489 Sansui 10695 Sanyo 10695 Sharp 10630, 10675, 12250 Shinsonic 10533 Sonic Blue 10869 Sylvania 10675 Symphonic 10675 TCL 12587 Technics 10490 Tivo 11503 Toshiba 10503, 11769, 10695, 11154, 11503, 12006, 12277 Urban Concepts 10503 Viore 12553 Vizio 12563 Vtrek 12587 Xbox 10522, 12083 Yamaha 10490, 10539, 10497, 10817, 12298 Zenith 10503, 10591, 10741, 10869 DVD player / Reproductor de DVD Brand Code No. Sony 11033, 11070, 11431 Accurian 10675 Apex Digital 11056 Funai 10675 Go Video 10741 JVC 11164 LG 10741 Magnavox 10646, 10675 Panasonic 10490, 11579 Brand Code No. Philips 10646 Pioneer 10631 RCA 10522 Samsung 10490 Sharp 10675 Sylvania 10675 Toshiba 12277 Zenith 10741 DVD recorder / Grabadora de DVD Blu-ray Disc/HD-DVD player/ Reproductor de Blu-ray Disc/HD-DVD Brand Code No. Sony 11516 Denon 12258 Insignia 10675, 12428, 12596 Integra 11769, 12147 LG 10741 Magnavox 10675 Marantz 12414, 12432 Microsoft 12083 NAD 12572 Olevia 12331 Onkyo 11769, 12147 Oppo 12545 Brand Code No. Panasonic 11641 Philips 12084, 12434 Pioneer 10142, 12442 RCA 11769 Samsung 10199 Sharp 12250 Sylvania 10675 Toshiba 11769 Viore 12553 Vizio 12563 Xbox 12083 Yamaha 12298 Brand Code No. Sony 00810, 00000 Acer 01339 Action 00650 Brand Code No. Midland 00051 Mitsubishi 01250, 00150, 00836 NAD 00156 TV / TV BPL 01543 Broksonic 00463 Carver 00054 Celebrity 00000 Coby 02306, 02345, 02348 Commercial Solutions 01447 Crosley 00054 Curtis 02352 Curtis Mathes 00054, 00154, 00702, 01661 Daewoo 01661 Digital Lifestyles 01765 Durabrand 00463, 00171 Panasonic 01480, 00051, 00650 PARK 02104 Penney 00156, 00051 Petters 01523 Philco 00054 Philips 01454, 00054, 00690, 01744, 02372 Pioneer 01457, 01260 Polaroid 01523, 01276, 01314, 01687 Portland 01661 Prism 00051 Proscan 01447, 02147, 02256 Proview 01687 If your device is not listed, try the Search function (see “Searching for the correct code”). 2 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 3 Enter the manufacturer’s code (01454). The SET indicator flashes three times and turns off. „ Operate the device 1 Aim the RM-VZ220 directly at the device. 2 Press the Device Select button for the device you want to operate. 3 Press POWER to turn on the device. 4 Press buttons on the RM-VZ220 to check that they function. See “Remote Button Descriptions” for the functions of buttons for each device. If the RM-VZ220 does not seem to be working… ˎ Check that you have set the correct manufacturer’s code. ˎ Try repeating the setup procedure using another manufacturer’s code (if listed for your device). If you still cannot operate the RM-VZ220 after trying all the listed codes, try the Search function (see “Searching for the correct code”). Notes ˎ If the setting is incomplete, the SET indicator flashes once and the indicators turn off. Start again from the beginning. ˎ If no operations are performed for 10 seconds while setting, the setting will be canceled, and must be restarted. ˎ To cancel the process, press SET any time. The SET indicator turns off. SET POWER Device Select buttons Number buttons The SET indicator lights up. Searching for the correct code You can set the manufacturer’s code using the Search function. 1 Power on the device with its power switch. 2 Aim the RM-VZ220 at the device you want to set. 3 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 4 Enter 9 - 2 - 2 using the number buttons. The SET indicator flashes three times. 5 Press and hold à to start searching. When the device turns off, release the button. If you overshoot the required code, you can search for the next or previous code using the ß or ù button. 6 Press . The SET indicator flashes three times and turns off. 7 Check if the code number works correctly (see “Remote Button Descriptions”). If you still cannot operate the device, repeat steps to search for another code that works for most functions of your device. Checking the manufacturer’s code you have set 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 2 Enter 9 - 3 - 3 using the number buttons. The SET indicator flashes three times. 3 Press à. 4 When the SET indicator starts flashing, count the number of flashes. Short flash(es) indicate which digit (first, second, etc.), followed by long flash(es) to indicate the digit number (i.e., 2 long flashes represent the number 2). “0” is indicated by rapid flashing. Determine the 5-digit code number this way. To recheck, press à. 5 Press SET to finish. Clearing the automatic power-on control (Sony devices only) The Device Select buttons are preset to automatically turn on a device when pressed. To cancel the function: 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press , then release both buttons. 2 Enter 9 - 7 - 7 using the number buttons. The SET indicator flashes three times. 3 Press the desired Device Select button. The SET indicator flashes three times and turns off. To set the function again, perform the same procedure above. Restoring the factory settings You can clear all the settings and reset the RM-VZ220 to its factory settings. 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press , then release both buttons. 2 Enter 9 - 0 - 0 using the number buttons. The SET indicator flashes three times. To cancel, press any button except . 3 Press . The SET indicator flashes three times and turns off. Remote Button Descriptions General ȩȪ SET: Press to set up the RM-VZ220. The indicator lights or flashes while setting. ȫ Device Select buttons: Press to select the device to operate. Ȯ GUIDE: Displays the program guide (EPG). ȯ j/„/V/p/ : Moves the cursor to select a menu item/enters the selected item. ȱ RETURN: Returns to the previous display/exits the menu. ȳ VOL +/–: Turns the volume up/down. ȸ POWER: Turns the selected device on and off. Ⱦ MUTING: Mutes the volume. Press again to turn muting off. ɀ SLEEP: Enables the Sleep function (when available). The number 5, CH+, and à buttons each have a tactile dot for ease of use. The GUIDE and RETURN buttons do not work for a VCR. Note on the VOL+/– and MUTING buttons When a TV or other video device is selected, the TV’s volume is controlled. When a DVD Home Theater is selected, its volume can be controlled. TV Ȭ Ã: VIDEO 1 input : VIDEO 2 input : HDMI input Ñ: RGB input ù: (PIP INPUT) Changes the input mode of the “window” picture. à: (PIP) Turns the “window” picture on and off. ß: (PIP MOVE) Moves the location of the “window” picture. ê: (PIP STILL) Freezes the “window” picture. Ą: (PIP SWAP) Switches between “main” and “window” picture. ȭ A: Red button B: Green button C: Yellow button D: Blue button Ȱ LIST: (CAPTION) Displays closed captioning. Ȳ MENU: Calls up the menu display. ȴ INPUT: Changes the input mode. ȵȶɁ 1 – 9, 0, ENTER, ˎ (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). ȹ PAGE +/–: (PIP CH +/–) Changes the channel up/down in the “window” picture. Ⱥ FAVORITES: Enables the Favorite function. Ȼ INFO: Displays program information. ȼ OPTIONS: Displays the options menu. Ƚ RECALL: Selects the channel previously selected. ȿ CH +/–: Switches the channel up/ down. Cable set top box/IPTV Ȭ Ã: Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). Ñ: Proceeds to the next location. ù: Fast reverses. à: Plays. ß: Fast forwards. Ć: Records. ê: Pauses. Ą: Stops. ȭ A, B, C buttons D: (Live TV) Displays Master Guide. Ȱ LIST: Displays the title of recorded program. Ȳ MENU: Calls up the menu display. ȴ INPUT: Changes the input mode. ȵ ȶ Ɂ 1 – 9, 0, ENTER, ˎ (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). ȹ PAGE +/–: Page up/down Ⱥ FAVORITES: Enables the Favorite function. Ȼ INFO: Displays program information. ȼ OPTIONS: Displays the options menu. Ƚ RECALL: Switches between the current and previous channel. ȿ CH +/–: Switches the channel up/ down. Satellite receiver Ȭ Ã: Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). Ñ: Proceeds to the next location. ù: Fast reverses. à: Plays. ß: Fast forwards. Ć: Records. ê: Pauses. Ą: Stops. ȭ A: Red button B: Green button C: Yellow button D: Blue button Ȱ LIST: Displays the title of recorded program/PVR menu. Ȳ MENU: Calls up the menu display. ȴ INPUT: (TV/SAT) Switches the output between SAT and TV. ȵ ȶ Ɂ 1 – 9, 0, ENTER, ˎ (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). ȹ PAGE +/–: Page up/down Ⱥ FAVORITES: Enables the Favorite function. Ȼ INFO: Displays program information. ȼ OPTIONS: Displays the Satellite dish menu/Station Index. Ƚ RECALL: Tunes to the last tuned station. ȿ CH +/–: Switches the channel up/ down. VCR Ȭ ù: Rewinds. à: Plays. ß: Fast forwards. Ć: Records. ê: Pauses. Ą: Stops. ȴ INPUT: Changes the input mode. ȵ 1 – 9, 0: Number buttons ȷ ì: Ejects a tape. Ȼ INFO: (DISPLAY) Displays the playback information. ȼ OPTIONS: (ANT/SW) Switches the antenna output. Ƚ RECALL: (DRIVE SELECT) Selects the deck. ȿ CH +/–: Switches the channel up/ down. Ɂ ENTER: Enters the selected item. DVD player/recorder Ȭ Ã: Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). Ñ: Skips to the next chapter/ track. ù: Fast reverses. à: Plays. ß: Fast forwards. Ć: Records (for DVD recorder). ê: Pauses. Ą: Stops. ȭ A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. Ȱ LIST: Displays the Title List. Ȳ MENU: Displays the DVD menu. ȴ INPUT: Changes the input mode. ȵ 1 – 9, 0: Number buttons ȶ ˎ (dot): (+10) Selects numbers 10 and above. ȷ ì: Opens/closes the disc tray. ȹ PAGE +: (DVD) Selects the DVD drive. PAGE –: (HDD) Selects the internal HDD (hard disk drive). Ⱥ FAVORITES: (TOP MENU) Displays the Top Menu. Ȼ INFO: (DISPLAY) Displays the playback information. ȼ OPTIONS: Displays the options menu. Ƚ RECALL: (DRIVE SELECT) Switches between HDD and DVD. ȿ CH +/–: Switches the channel up/ down (for DVD recorder). Ɂ ENTER: Enters the selected item. Blu-ray Disc/HD-DVD player Ȭ Ã: Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). Ñ: Skips to the next chapter/ track. ù: Fast reverses. à: Plays. ß: Fast forwards. Ć: Records (for BD recorder). ê: Pauses. Ą: Stops. ȭ A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. Ȳ MENU: Displays the Pop-up Menu/ Disc Menu. ȴ INPUT: Changes the input mode. ȵ 1 – 9, 0: Number buttons ȶ ˎ (dot): (+10) Selects numbers 10 and above. ȷ ì: Opens/closes the disc tray. ȹ PAGE +: (BD) Selects the BD drive. PAGE –: (HDD) Selects the internal HDD (hard disk drive). Ⱥ FAVORITES: (TOP MENU) Displays the Top Menu. Ȼ INFO: (DISPLAY) Displays the playback information. ȼ OPTIONS: Displays the options menu. Ɂ ENTER: Enters the selected item. DVR (digital video recorder)/PVR (personal video recorder) Ȭ Ã: Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). Ñ: Proceeds to the next location. ù: Fast reverses. à: Plays. ß: Fast forwards. Ć: Records. ê: Pauses. Ą: Stops. ȭ A: (REPLAY*) Enables the Replay function for DVR/Replay TV. B: (Live TV*) Displays Master Guide. Ȱ LIST: Displays the title of recorded program. Ȳ MENU: Calls up the menu display. ȴ INPUT: Changes the input mode. ȵ 1 – 9, 0: Number buttons ȶ ˎ (dot): (+10) Selects numbers 10 and above. ȷ ì: Opens/closes the disc tray. ȹ PAGE +/–: Page up/down, Thumbs* up/down Ȼ INFO: (DISPLAY) Displays the playback information. Ƚ RECALL: Selects the channel previously selected. ȿ CH +/–: Switches the channel up/ down. Ɂ ENTER: Enters the selected item. * These buttons correspond to TiVo service or the Replay service. Refer to its instruction manual for details. DVD Home Theater Ȭ Ã: Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). Ñ: Skips to the next chapter/ track. ù: Fast reverses. à: Plays. ß: Fast forwards. Ć: Records. ê: Pauses. Ą: Stops. ȭ A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. Ȱ LIST: Enables the SOUND FIELD function. Ȳ MENU: Displays the DVD menu. ȴ INPUT: Changes the input mode. ȵ 1 – 9, 0: Number buttons ȶ ˎ (dot): (+10) Selects numbers 10 and above. ȷ ì: Opens/closes the disc tray. Ⱥ FAVORITES: (TOP MENU) Displays the Top Menu. Ȼ INFO: (DISPLAY) Displays the playback information. ȼ OPTIONS: Displays the amplifier menu. Ƚ RECALL: (BAND) Selects FM/AM. ȿ CH +/–: Presets or tunes frequency up/down. Ɂ ENTER: Enters the selected item. Notes on using the RM-VZ220 ˎ The RM-VZ220 will not perform functions that the device is not designed for. For example, if your TV does not have the muting function, MUTING on the RM-VZ220 will not function with your TV. ˎ The function of the buttons varies depending on settings/operating modes. The table of “Remote Button Descriptions” shows how the RM-VZ220 generally operates for each device in the preset mode. ˎ If your cable set top box can control volume, be sure to set its volume to a moderate level. If the volume on the cable set top box is turned down completely, you will not be able to adjust your TV’s volume with the RM-VZ220. Manufacturer’s Code List / Lista de códigos del fabricante English The following tables show brand names (Brand) and their corresponding code numbers (Code No.). 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 2 Enter the manufacturer’s code. The SET indicator flashes three times and turns off. Español La siguiente tabla muestra los nombres de las marcas (Brand) y el número de código correspondiente (Code No.). 1 Presione y mantenga presionado el botón SET durante más de 3 segundos. Se encenderá la luz indicadora SET. Mientras tiene presionado el botón SET, presione el botón de selección de dispositivo deseado y luego suelte ambos botones. 2 Ingrese el código del fabricante. El indicador SET parpadeará tres veces y se apagará. Brand Code No. Acer 01339 Action 00650 Admiral 00463 Akai 00812, 01675, 00702, 02232 Akira 01733 AOC 01365, 01589 Apex Digital 00748 Aventura 00171 Bell & Howell 00154 BPL 01543 Broksonic 00463 Carver 00054 Celebrity 00000 Coby 02306, 02345, 02348 Commercial Solutions 01447 Crosley 00054 Curtis 02352 Curtis Mathes 00054, 00154, 00702, 01661 Daewoo 01661 Digital Lifestyles 01765 Durabrand 00463, 00171 Dynex 01463, 01810, 02049 Electroband 00000 Electrograph 01755 Electrohome 00463 Elektra 01661 Element 01687 Emerson 01864, 00154, 00463, 00171, 01661, 01394 Emprex 01765 Envision 01365, 01589 ESA 00812, 00171 Fisher 00154 Funai 00171 Gateway 01755, 01756 GE 01447, 00051, 02359 GFM 00171 Haier 01748, 01749, 02309, 02449 Harman/Kardon 00054 Hisense 00748, 01314, 02098 Hitachi 01643, 02215, 02433 iLo 01684 Infinity 00054 Insignia 01564, 00171, 02049 JBL 00054 JCB 00000 JVC 00731, 01253, 01601, 01774 KDS 01687 Kolin 01331 LG 01423, 02358 LXI 00054, 00154, 00156 MAG 01687 Magnavox 01454, 01866, 00054, 01254, 01365, 02372 Marantz 00054 Matsushita 00650 Maxent 01755 Memorex 00154, 00463, 00150 MGA 00150 Midland 00051 Brand Code No. Mitsubishi 01250, 00150, 00836 NAD 00156 NEC 01797 NetTV 01755 Norcent 00748, 01365, 01589 Olevia 01610, 01144, 01331 Onida 01253, 02396 Optimus 00154, 00650 Orion 00463, 01463 Panasonic 01480, 00051, 00650 PARK 02104 Penney 00156, 00051 Petters 01523 Philco 00054 Philips 01454, 00054, 00690, 01744, 02372 Pioneer 01457, 01260 Polaroid 01523, 01276, 01314, 01687 Portland 01661 Prism 00051 Proscan 01447, 02147, 02256 Proview 01687 Quasar 00051, 00650 RadioShack 00154 RCA 01447, 01781, 02187, 02247, 02403, 02429, 02434 Realistic 00154 Sampo 01755 Samsung 00812, 00702 Sansui 00463 Sanyo 00154, 01142 Sceptre 01360, 01599 Scott 01711 Sears 00054, 00154, 00156, 00171 Sharp 00818 Sony 00810, 00000 Spectroniq 01687 Squareview 00171 Superscan 00864 Supreme 00000 SVA 00748 Sylvania 01864, 00054, 00171, 01314, 01394 Symphonic 00171 Syntax 01610, 01144, 01331 Tatung 01756 TCL 02403, 02429 Technics 00051 Techwood 00051 Teknika 00054, 00150 Telefunken 00702 Toshiba 01524, 00154, 00156, 00650 TVS 00463 Venturer 01865 Videocon 01540, 01541, 02436 Vidikron 00054 Viewsonic 01755, 00864, 00885, 01627, 01742 Viore 01684, 02104, 02352 Vizio 01758, 00864, 00885, 01756 VU 02098 TV / TV Brand Code No. Wards 00054 Waycon 00156 Westinghouse 01712, 00885, 01577 White Westinghouse 00463, 01661 Wyse 01365 Zenith 00463, 01661 Brand Code No. Accurian 10675 Akai 10695 Allegro 10869 Apex Digital 10672, 11056 Bel Canto Design 11571 Broksonic 10695 CineVision 10869 Citizen 10695 CyberHome 11024 Daewoo 10869 Denon 10490, 11634, 12258 Disney 10675, 11270 Emerson 10591, 10675 Enterprise 10591 Funai 10675 GE 10522 GFM 10675 Go Video 10744, 10741, 10869, 11044, 11075 GoldStar 10741 Harman/Kardon 11229 Hitachi 10573, 10664 Hiteker 10672 Insignia 10675, 12428, 12596 Integra 11769, 10627, 12147 JVC 10623, 10867, 11164 Kenwood 10490 LG 10591, 10741, 10869 Magnavox 10503, 10539, 10646, 10675, 11354 Marantz 10539, 12414, 12432 Memorex 10695, 11270, 12213 Microsoft 10522, 12083 Mitsubishi 11521 NAD 10741, 12572 Olevia 12331 Onkyo 10503, 11769, 10627, 11627, 12147 Brand Code No. Oppo 10575, 12545 Panasonic 10490, 11579, 11641 Philco 10675 Philips 10503, 10539, 12056, 12084, 10646, 10675, 11267, 11354, 12434 Pioneer 10142, 10631, 11571, 12442 Polk Audio 10539 Presidian 10675 Proscan 10522 RCA 10522, 11769, 10822, 12213, 12587, 12592, 12594 Rio 10869 Rotel 10623 Samsung 10490, 10573, 10199, 11044, 11075, 12329, 12489 Sansui 10695 Sanyo 10695 Sharp 10630, 10675, 12250 Shinsonic 10533 Sonic Blue 10869 Sony 11633, 10533, 10864, 11033, 11070, 11431, 11516 Sylvania 10675 Symphonic 10675 TCL 12587 Technics 10490 Tivo 11503 Toshiba 10503, 11769, 10695, 11154, 11503, 12006, 12277 Urban Concepts 10503 Viore 12553 Vizio 12563 Vtrek 12587 Xbox 10522, 12083 Yamaha 10490, 10539, 10497, 10817, 12298 Zenith 10503, 10591, 10741, 10869 DVD player / Reproductor de DVD Brand Code No. Accurian 10675 Apex Digital 11056 Funai 10675 Go Video 10741 JVC 11164 LG 10741 Magnavox 10646, 10675 Panasonic 10490, 11579 Philips 10646 Brand Code No. Pioneer 10631 RCA 10522 Samsung 10490 Sharp 10675 Sony 11033, 11070, 11431 Sylvania 10675 Toshiba 12277 Zenith 10741 DVD recorder / Grabadora de DVD Blu-ray Disc/HD-DVD player/ Reproductor de Blu-ray Disc/HD-DVD Brand Code No. Denon 12258 Insignia 10675, 12428, 12596 Integra 11769, 12147 LG 10741 Magnavox 10675 Marantz 12414, 12432 Microsoft 12083 NAD 12572 Olevia 12331 Onkyo 11769, 12147 Oppo 12545 Panasonic 11641 Brand Code No. Philips 12084, 12434 Pioneer 10142, 12442 RCA 11769 Samsung 10199 Sharp 12250 Sony 11516 Sylvania 10675 Toshiba 11769 Viore 12553 Vizio 12563 Xbox 12083 Yamaha 12298 RM-VZ220_U [US,ES] 4-170-642-12(1) hree times. searching. release the button. ed code, you can search for the next or previous button. hree times and turns off. works correctly (see “Remote Button he device, repeat steps to search for another nctions of your device. facturer’s code you have set e than 3 seconds. . wn, press the desired Device Select button, mber buttons. hree times. rts flashing, count the number of flashes. ch digit (first, second, etc.), followed by long it number (i.e., 2 long flashes represent the by rapid flashing. number this way. To recheck, press à. atic power-on control (Sony preset to automatically turn on a device when e than 3 seconds. . wn, press , then release both buttons. mber buttons. hree times. lect button. hree times and turns off. form the same procedure above. ry settings nd reset the RM-VZ220 to its factory settings. e than 3 seconds. . wn, press , then release both buttons. mber buttons. hree times. except . hree times and turns off. General ȩȪ SET: Press to set up the RM-VZ220. The indicator lights or flashes while setting. ȫ Device Select buttons: Press to select the device to operate. Ȯ GUIDE: Displays the program guide (EPG). ȯ j/„/V/p/ : Moves the cursor to select a menu item/enters the selected item. ȱ RETURN: Returns to the previous display/exits the menu. ȳ VOL +/–: Turns the volume up/down. ȸ POWER: Turns the selected device on and off. Ⱦ MUTING: Mutes the volume. Press again to turn muting off. ɀ SLEEP: Enables the Sleep function (when available). The number 5, CH+, and à buttons each have a tactile dot for ease of use. The GUIDE and RETURN buttons do not work for a VCR. Note on the VOL+/– and MUTING buttons When a TV or other video device is selected, the TV’s volume is controlled. When a DVD Home Theater is selected, its volume can be controlled. TV Ȭ Ã: VIDEO 1 input : VIDEO 2 input : HDMI input Ñ: RGB input ù: (PIP INPUT) Changes the input mode of the “window” picture. à: (PIP) Turns the “window” picture on and off. ß: (PIP MOVE) Moves the location of the “window” picture. ê: (PIP STILL) Freezes the “window” picture. Ą: (PIP SWAP) Switches between “main” and “window” picture. ȭ A: Red button B: Green button C: Yellow button D: Blue button Ȱ LIST: (CAPTION) Displays closed captioning. Ȳ MENU: Calls up the menu display. ȴ INPUT: Changes the input mode. ȵȶɁ 1 – 9, 0, ENTER, ˎ (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). ȹ PAGE +/–: (PIP CH +/–) Changes the channel up/down in the “window” picture. Ⱥ FAVORITES: Enables the Favorite function. Ȼ INFO: Displays program information. ȼ OPTIONS: Displays the options menu. Ƚ RECALL: Selects the channel previously selected. ȿ CH +/–: Switches the channel up/ down. ê: Pauses. Ą: Stops. ȭ A, B, C buttons D: (Live TV) Displays Master Guide. Ȱ LIST: Displays the title of recorded program. ȼ OPTIONS: Displays the options menu. Ƚ RECALL: Switches between the current and previous channel. ȿ CH +/–: Switches the channel up/ down. Satellite receiver Ȭ Ã: Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). Ñ: Proceeds to the next location. ù: Fast reverses. à: Plays. ß: Fast forwards. Ć: Records. ê: Pauses. Ą: Stops. ȭ A: Red button B: Green button C: Yellow button D: Blue button Ȱ LIST: Displays the title of recorded program/PVR menu. Ȳ MENU: Calls up the menu display. ȴ INPUT: (TV/SAT) Switches the output between SAT and TV. ȵ ȶ Ɂ 1 – 9, 0, ENTER, ˎ (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). ȹ PAGE +/–: Page up/down Ⱥ FAVORITES: Enables the Favorite function. Ȼ INFO: Displays program information. ȼ OPTIONS: Displays the Satellite dish menu/Station Index. Ƚ RECALL: Tunes to the last tuned station. ȿ CH +/–: Switches the channel up/ down. VCR Ȭ ù: Rewinds. à: Plays. ß: Fast forwards. Ć: Records. ê: Pauses. Ą: Stops. ȴ INPUT: Changes the input mode. ȵ 1 – 9, 0: Number buttons ȷ ì: Ejects a tape. Ȼ INFO: (DISPLAY) Displays the playback information. ȼ OPTIONS: (ANT/SW) Switches the antenna output. Ƚ RECALL: (DRIVE SELECT) Selects the deck. ȿ CH +/–: Switches the channel up/ down. Ɂ ENTER: Enters the selected item. DVD player/recorder Ȭ Ã: Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). Ñ: Skips to the next chapter/ track. ù: Fast reverses. à: Plays. ß: Fast forwards. Ć: Records (for DVD recorder). ê: Pauses. Ą: Stops. ȭ A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. Ȱ LIST: Displays the Title List. Ȳ MENU: Displays the DVD menu. ȴ INPUT: Changes the input mode. ȵ 1 – 9, 0: Number buttons ȶ ˎ (dot): (+10) Selects numbers 10 and above. ȷ ì: Opens/closes the disc tray. ȹ PAGE +: (DVD) Selects the DVD drive. PAGE –: (HDD) Selects the internal HDD (hard disk drive). Ⱥ FAVORITES: (TOP MENU) Displays the Top Menu. Ȼ INFO: (DISPLAY) Displays the playback information. ȼ OPTIONS: Displays the options menu. Ƚ RECALL: (DRIVE SELECT) Switches between HDD and DVD. ȿ CH +/–: Switches the channel up/ down (for DVD recorder). Ɂ ENTER: Enters the selected item. Ć: Records (for BD recorder). ê: Pauses. Ą: Stops. ȭ A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. Displays the Top Menu. Ȼ INFO: (DISPLAY) Displays the playback information. ȼ OPTIONS: Displays the options menu. Ɂ ENTER: Enters the selected item. DVR (digital video recorder)/PVR (personal video recorder) Ȭ Ã: Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). Ñ: Proceeds to the next location. ù: Fast reverses. à: Plays. ß: Fast forwards. Ć: Records. ê: Pauses. Ą: Stops. ȭ A: (REPLAY*) Enables the Replay function for DVR/Replay TV. B: (Live TV*) Displays Master Guide. Ȱ LIST: Displays the title of recorded program. Ȳ MENU: Calls up the menu display. ȴ INPUT: Changes the input mode. ȵ 1 – 9, 0: Number buttons ȶ ˎ (dot): (+10) Selects numbers 10 and above. ȷ ì: Opens/closes the disc tray. ȹ PAGE +/–: Page up/down, Thumbs* up/down Ȼ INFO: (DISPLAY) Displays the playback information. Ƚ RECALL: Selects the channel previously selected. ȿ CH +/–: Switches the channel up/ down. Ɂ ENTER: Enters the selected item. * These buttons correspond to TiVo service or the Replay service. Refer to its instruction manual for details. DVD Home Theater Ȭ Ã: Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). Ñ: Skips to the next chapter/ track. ù: Fast reverses. à: Plays. ß: Fast forwards. Ć: Records. ê: Pauses. Ą: Stops. ȭ A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. Ȱ LIST: Enables the SOUND FIELD function. Ȳ MENU: Displays the DVD menu. ȴ INPUT: Changes the input mode. ȵ 1 – 9, 0: Number buttons ȶ ˎ (dot): (+10) Selects numbers 10 and above. ȷ ì: Opens/closes the disc tray. Ⱥ FAVORITES: (TOP MENU) Displays the Top Menu. Ȼ INFO: (DISPLAY) Displays the playback information. ȼ OPTIONS: Displays the amplifier menu. Ƚ RECALL: (BAND) Selects FM/AM. ȿ CH +/–: Presets or tunes frequency up/down. Ɂ ENTER: Enters the selected item. Notes on using the RM-VZ220 ˎ The RM-VZ220 will not perform functions that the device is not designed for. For example, if your TV does not have the muting function, MUTING on the RM-VZ220 will not function with your TV. ˎ The function of the buttons varies depending on settings/operating modes. The table of “Remote Button Descriptions” shows how the RM-VZ220 generally operates for each device in the preset mode. ˎ If your cable set top box can control volume, be sure to set its volume to a moderate level. If the volume on the cable set top box is turned down completely, you will not be able to adjust your TV’s volume with the RM-VZ220. p g p then release both buttons. 2 Enter the manufacturer’s code. The SET indicator flashes three times and turns off. Español La siguiente tabla muestra los nombres de las marcas (Brand) y el número de código correspondiente (Code No.). 1 Presione y mantenga presionado el botón SET durante más de 3 segundos. Se encenderá la luz indicadora SET. Mientras tiene presionado el botón SET, presione el botón de selección de dispositivo deseado y luego suelte ambos botones. 2 Ingrese el código del fabricante. El indicador SET parpadeará tres veces y se apagará. Brand Code No. Acer 01339 Action 00650 Admiral 00463 Akai 00812, 01675, 00702, 02232 Akira 01733 AOC 01365, 01589 Apex Digital 00748 Aventura 00171 Bell & Howell 00154 BPL 01543 Broksonic 00463 Carver 00054 Celebrity 00000 Coby 02306, 02345, 02348 Commercial Solutions 01447 Crosley 00054 Curtis 02352 Curtis Mathes 00054, 00154, 00702, 01661 Daewoo 01661 Digital Lifestyles 01765 Durabrand 00463, 00171 Dynex 01463, 01810, 02049 Electroband 00000 Electrograph 01755 Electrohome 00463 Elektra 01661 Element 01687 Emerson 01864, 00154, 00463, 00171, 01661, 01394 Emprex 01765 Envision 01365, 01589 ESA 00812, 00171 Fisher 00154 Funai 00171 Gateway 01755, 01756 GE 01447, 00051, 02359 GFM 00171 Haier 01748, 01749, 02309, 02449 Harman/Kardon 00054 Hisense 00748, 01314, 02098 Hitachi 01643, 02215, 02433 iLo 01684 Infinity 00054 Insignia 01564, 00171, 02049 JBL 00054 JCB 00000 JVC 00731, 01253, 01601, 01774 KDS 01687 Kolin 01331 LG 01423, 02358 LXI 00054, 00154, 00156 MAG 01687 Magnavox 01454, 01866, 00054, 01254, 01365, 02372 Marantz 00054 Matsushita 00650 Maxent 01755 Memorex 00154, 00463, 00150 MGA 00150 Midland 00051 Brand Code No. Mitsubishi 01250, 00150, 00836 NAD 00156 NEC 01797 NetTV 01755 Norcent 00748, 01365, 01589 Olevia 01610, 01144, 01331 Onida 01253, 02396 Optimus 00154, 00650 Orion 00463, 01463 Panasonic 01480, 00051, 00650 PARK 02104 Penney 00156, 00051 Petters 01523 Philco 00054 Philips 01454, 00054, 00690, 01744, 02372 Pioneer 01457, 01260 Polaroid 01523, 01276, 01314, 01687 Portland 01661 Prism 00051 Proscan 01447, 02147, 02256 Proview 01687 Quasar 00051, 00650 RadioShack 00154 RCA 01447, 01781, 02187, 02247, 02403, 02429, 02434 Realistic 00154 Sampo 01755 Samsung 00812, 00702 Sansui 00463 Sanyo 00154, 01142 Sceptre 01360, 01599 Scott 01711 Sears 00054, 00154, 00156, 00171 Sharp 00818 Sony 00810, 00000 Spectroniq 01687 Squareview 00171 Superscan 00864 Supreme 00000 SVA 00748 Sylvania 01864, 00054, 00171, 01314, 01394 Symphonic 00171 Syntax 01610, 01144, 01331 Tatung 01756 TCL 02403, 02429 Technics 00051 Techwood 00051 Teknika 00054, 00150 Telefunken 00702 Toshiba 01524, 00154, 00156, 00650 TVS 00463 Venturer 01865 Videocon 01540, 01541, 02436 Vidikron 00054 Viewsonic 01755, 00864, 00885, 01627, 01742 Viore 01684, 02104, 02352 Vizio 01758, 00864, 00885, 01756 VU 02098 TV / TV Akai 10695 Allegro 10869 Apex Digital 10672, 11056 Bel Canto Design 11571 Broksonic 10695 CineVision 10869 Citizen 10695 CyberHome 11024 Daewoo 10869 Denon 10490, 11634, 12258 Disney 10675, 11270 Emerson 10591, 10675 Enterprise 10591 Funai 10675 GE 10522 GFM 10675 Go Video 10744, 10741, 10869, 11044, 11075 GoldStar 10741 Harman/Kardon 11229 Hitachi 10573, 10664 Hiteker 10672 Insignia 10675, 12428, 12596 Integra 11769, 10627, 12147 JVC 10623, 10867, 11164 Kenwood 10490 LG 10591, 10741, 10869 Magnavox 10503, 10539, 10646, 10675, 11354 Marantz 10539, 12414, 12432 Memorex 10695, 11270, 12213 Microsoft 10522, 12083 Mitsubishi 11521 NAD 10741, 12572 Olevia 12331 Onkyo 10503, 11769, 10627, 11627, 12147 pp Panasonic 10490, 11579, 11641 Philco 10675 Philips 10503, 10539, 12056, 12084, 10646, 10675, 11267, 11354, 12434 Pioneer 10142, 10631, 11571, 12442 Polk Audio 10539 Presidian 10675 Proscan 10522 RCA 10522, 11769, 10822, 12213, 12587, 12592, 12594 Rio 10869 Rotel 10623 Samsung 10490, 10573, 10199, 11044, 11075, 12329, 12489 Sansui 10695 Sanyo 10695 Sharp 10630, 10675, 12250 Shinsonic 10533 Sonic Blue 10869 Sony 11633, 10533, 10864, 11033, 11070, 11431, 11516 Sylvania 10675 Symphonic 10675 TCL 12587 Technics 10490 Tivo 11503 Toshiba 10503, 11769, 10695, 11154, 11503, 12006, 12277 Urban Concepts 10503 Viore 12553 Vizio 12563 Vtrek 12587 Xbox 10522, 12083 Yamaha 10490, 10539, 10497, 10817, 12298 Zenith 10503, 10591, 10741, 10869 Brand Code No. Accurian 10675 Apex Digital 11056 Funai 10675 Go Video 10741 JVC 11164 LG 10741 Magnavox 10646, 10675 Panasonic 10490, 11579 Philips 10646 Brand Code No. Pioneer 10631 RCA 10522 Samsung 10490 Sharp 10675 Sony 11033, 11070, 11431 Sylvania 10675 Toshiba 12277 Zenith 10741 DVD recorder / Grabadora de DVD Blu-ray Disc/HD-DVD player/ Reproductor de Blu-ray Disc/HD-DVD Brand Code No. Denon 12258 Insignia 10675, 12428, 12596 Integra 11769, 12147 LG 10741 Magnavox 10675 Marantz 12414, 12432 Microsoft 12083 NAD 12572 Olevia 12331 Onkyo 11769, 12147 Oppo 12545 Panasonic 11641 Brand Code No. Philips 12084, 12434 Pioneer 10142, 12442 RCA 11769 Samsung 10199 Sharp 12250 Sony 11516 Sylvania 10675 Toshiba 11769 Viore 12553 Vizio 12563 Xbox 12083 Yamaha 12298 RM-VZ220_U [US,ES] 4-170-642-12(1) hree times and turns off. works correctly (see “Remote Button he device, repeat steps to search for another nctions of your device. facturer’s code you have set e than 3 seconds. . wn, press the desired Device Select button, mber buttons. hree times. rts flashing, count the number of flashes. ch digit (first, second, etc.), followed by long it number (i.e., 2 long flashes represent the by rapid flashing. number this way. To recheck, press à. atic power-on control (Sony preset to automatically turn on a device when e than 3 seconds. . wn, press , then release both buttons. mber buttons. hree times. lect button. hree times and turns off. form the same procedure above. ry settings nd reset the RM-VZ220 to its factory settings. e than 3 seconds. . wn, press , then release both buttons. mber buttons. hree times. except . hree times and turns off. General ȩȪ SET: Press to set up the RM-VZ220. The indicator lights or flashes while setting. ȫ Device Select buttons: Press to select the device to operate. Ȯ GUIDE: Displays the program guide (EPG). ȯ j/„/V/p/ : Moves the cursor to select a menu item/enters the selected item. ȱ RETURN: Returns to the previous display/exits the menu. ȳ VOL +/–: Turns the volume up/down. ȸ POWER: Turns the selected device on and off. Ⱦ MUTING: Mutes the volume. Press again to turn muting off. ɀ SLEEP: Enables the Sleep function (when available). The number 5, CH+, and à buttons each have a tactile dot for ease of use. The GUIDE and RETURN buttons do not work for a VCR. Note on the VOL+/– and MUTING buttons When a TV or other video device is selected, the TV’s volume is controlled. When a DVD Home Theater is selected, its volume can be controlled. TV Ȭ Ã: VIDEO 1 input : VIDEO 2 input : HDMI input Ñ: RGB input ù: (PIP INPUT) Changes the input mode of the “window” picture. à: (PIP) Turns the “window” picture on and off. ß: (PIP MOVE) Moves the location of the “window” picture. ê: (PIP STILL) Freezes the “window” picture. Ą: (PIP SWAP) Switches between “main” and “window” picture. ȭ A: Red button B: Green button C: Yellow button D: Blue button Ȱ LIST: (CAPTION) Displays closed captioning. Ȳ MENU: Calls up the menu display. ȴ INPUT: Changes the input mode. ȵȶɁ 1 – 9, 0, ENTER, ˎ (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). ȹ PAGE +/–: (PIP CH +/–) Changes the channel up/down in the “window” picture. Ⱥ FAVORITES: Enables the Favorite function. Ȼ INFO: Displays program information. ȼ OPTIONS: Displays the options menu. Ƚ RECALL: Selects the channel previously selected. ȿ CH +/–: Switches the channel up/ down. program. Satellite receiver Ȭ Ã: Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). Ñ: Proceeds to the next location. ù: Fast reverses. à: Plays. ß: Fast forwards. Ć: Records. ê: Pauses. Ą: Stops. ȭ A: Red button B: Green button C: Yellow button D: Blue button Ȱ LIST: Displays the title of recorded program/PVR menu. Ȳ MENU: Calls up the menu display. ȴ INPUT: (TV/SAT) Switches the output between SAT and TV. ȵ ȶ Ɂ 1 – 9, 0, ENTER, ˎ (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). ȹ PAGE +/–: Page up/down Ⱥ FAVORITES: Enables the Favorite function. Ȼ INFO: Displays program information. ȼ OPTIONS: Displays the Satellite dish menu/Station Index. Ƚ RECALL: Tunes to the last tuned station. ȿ CH +/–: Switches the channel up/ down. VCR Ȭ ù: Rewinds. à: Plays. ß: Fast forwards. Ć: Records. ê: Pauses. Ą: Stops. ȴ INPUT: Changes the input mode. ȵ 1 – 9, 0: Number buttons ȷ ì: Ejects a tape. Ȼ INFO: (DISPLAY) Displays the playback information. ȼ OPTIONS: (ANT/SW) Switches the antenna output. Ƚ RECALL: (DRIVE SELECT) Selects the deck. ȿ CH +/–: Switches the channel up/ down. Ɂ ENTER: Enters the selected item. DVD player/recorder Ȭ Ã: Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). Ñ: Skips to the next chapter/ track. ù: Fast reverses. à: Plays. ß: Fast forwards. Ć: Records (for DVD recorder). ê: Pauses. Ą: Stops. ȭ A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. Ȱ LIST: Displays the Title List. Ȳ MENU: Displays the DVD menu. ȴ INPUT: Changes the input mode. ȵ 1 – 9, 0: Number buttons ȶ ˎ (dot): (+10) Selects numbers 10 and above. ȷ ì: Opens/closes the disc tray. ȹ PAGE +: (DVD) Selects the DVD drive. PAGE –: (HDD) Selects the internal HDD (hard disk drive). Ⱥ FAVORITES: (TOP MENU) Displays the Top Menu. Ȼ INFO: (DISPLAY) Displays the playback information. ȼ OPTIONS: Displays the options menu. Ƚ RECALL: (DRIVE SELECT) Switches between HDD and DVD. ȿ CH +/–: Switches the channel up/ down (for DVD recorder). Ɂ ENTER: Enters the selected item. subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. DVR (digital video recorder)/PVR (personal video recorder) Ȭ Ã: Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). Ñ: Proceeds to the next location. ù: Fast reverses. à: Plays. ß: Fast forwards. Ć: Records. ê: Pauses. Ą: Stops. ȭ A: (REPLAY*) Enables the Replay function for DVR/Replay TV. B: (Live TV*) Displays Master Guide. Ȱ LIST: Displays the title of recorded program. Ȳ MENU: Calls up the menu display. ȴ INPUT: Changes the input mode. ȵ 1 – 9, 0: Number buttons ȶ ˎ (dot): (+10) Selects numbers 10 and above. ȷ ì: Opens/closes the disc tray. ȹ PAGE +/–: Page up/down, Thumbs* up/down Ȼ INFO: (DISPLAY) Displays the playback information. Ƚ RECALL: Selects the channel previously selected. ȿ CH +/–: Switches the channel up/ down. Ɂ ENTER: Enters the selected item. * These buttons correspond to TiVo service or the Replay service. Refer to its instruction manual for details. DVD Home Theater Ȭ Ã: Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). Ñ: Skips to the next chapter/ track. ù: Fast reverses. à: Plays. ß: Fast forwards. Ć: Records. ê: Pauses. Ą: Stops. ȭ A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. Ȱ LIST: Enables the SOUND FIELD function. Ȳ MENU: Displays the DVD menu. ȴ INPUT: Changes the input mode. ȵ 1 – 9, 0: Number buttons ȶ ˎ (dot): (+10) Selects numbers 10 and above. ȷ ì: Opens/closes the disc tray. Ⱥ FAVORITES: (TOP MENU) Displays the Top Menu. Ȼ INFO: (DISPLAY) Displays the playback information. ȼ OPTIONS: Displays the amplifier menu. Ƚ RECALL: (BAND) Selects FM/AM. ȿ CH +/–: Presets or tunes frequency up/down. Ɂ ENTER: Enters the selected item. Notes on using the RM-VZ220 ˎ The RM-VZ220 will not perform functions that the device is not designed for. For example, if your TV does not have the muting function, MUTING on the RM-VZ220 will not function with your TV. ˎ The function of the buttons varies depending on settings/operating modes. The table of “Remote Button Descriptions” shows how the RM-VZ220 generally operates for each device in the preset mode. ˎ If your cable set top box can control volume, be sure to set its volume to a moderate level. If the volume on the cable set top box is turned down completely, you will not be able to adjust your TV’s volume with the RM-VZ220. La siguiente tabla muestra los nombres de las marcas (Brand) y el número de código correspondiente (Code No.). 1 Presione y mantenga presionado el botón SET durante más de 3 segundos. Se encenderá la luz indicadora SET. Mientras tiene presionado el botón SET, presione el botón de selección de dispositivo deseado y luego suelte ambos botones. 2 Ingrese el código del fabricante. El indicador SET parpadeará tres veces y se apagará. Brand Code No. Acer 01339 Action 00650 Admiral 00463 Akai 00812, 01675, 00702, 02232 Akira 01733 AOC 01365, 01589 Apex Digital 00748 Aventura 00171 Bell & Howell 00154 BPL 01543 Broksonic 00463 Carver 00054 Celebrity 00000 Coby 02306, 02345, 02348 Commercial Solutions 01447 Crosley 00054 Curtis 02352 Curtis Mathes 00054, 00154, 00702, 01661 Daewoo 01661 Digital Lifestyles 01765 Durabrand 00463, 00171 Dynex 01463, 01810, 02049 Electroband 00000 Electrograph 01755 Electrohome 00463 Elektra 01661 Element 01687 Emerson 01864, 00154, 00463, 00171, 01661, 01394 Emprex 01765 Envision 01365, 01589 ESA 00812, 00171 Fisher 00154 Funai 00171 Gateway 01755, 01756 GE 01447, 00051, 02359 GFM 00171 Haier 01748, 01749, 02309, 02449 Harman/Kardon 00054 Hisense 00748, 01314, 02098 Hitachi 01643, 02215, 02433 iLo 01684 Infinity 00054 Insignia 01564, 00171, 02049 JBL 00054 JCB 00000 JVC 00731, 01253, 01601, 01774 KDS 01687 Kolin 01331 LG 01423, 02358 LXI 00054, 00154, 00156 MAG 01687 Magnavox 01454, 01866, 00054, 01254, 01365, 02372 Marantz 00054 Matsushita 00650 Maxent 01755 Memorex 00154, 00463, 00150 MGA 00150 Midland 00051 Brand Code No. Mitsubishi 01250, 00150, 00836 NAD 00156 NEC 01797 NetTV 01755 Norcent 00748, 01365, 01589 Olevia 01610, 01144, 01331 Onida 01253, 02396 Optimus 00154, 00650 Orion 00463, 01463 Panasonic 01480, 00051, 00650 PARK 02104 Penney 00156, 00051 Petters 01523 Philco 00054 Philips 01454, 00054, 00690, 01744, 02372 Pioneer 01457, 01260 Polaroid 01523, 01276, 01314, 01687 Portland 01661 Prism 00051 Proscan 01447, 02147, 02256 Proview 01687 Quasar 00051, 00650 RadioShack 00154 RCA 01447, 01781, 02187, 02247, 02403, 02429, 02434 Realistic 00154 Sampo 01755 Samsung 00812, 00702 Sansui 00463 Sanyo 00154, 01142 Sceptre 01360, 01599 Scott 01711 Sears 00054, 00154, 00156, 00171 Sharp 00818 Sony 00810, 00000 Spectroniq 01687 Squareview 00171 Superscan 00864 Supreme 00000 SVA 00748 Sylvania 01864, 00054, 00171, 01314, 01394 Symphonic 00171 Syntax 01610, 01144, 01331 Tatung 01756 TCL 02403, 02429 Technics 00051 Techwood 00051 Teknika 00054, 00150 Telefunken 00702 Toshiba 01524, 00154, 00156, 00650 TVS 00463 Venturer 01865 Videocon 01540, 01541, 02436 Vidikron 00054 Viewsonic 01755, 00864, 00885, 01627, 01742 Viore 01684, 02104, 02352 Vizio 01758, 00864, 00885, 01756 VU 02098 TV / TV CyberHome 11024 Daewoo 10869 Denon 10490, 11634, 12258 Disney 10675, 11270 Emerson 10591, 10675 Enterprise 10591 Funai 10675 GE 10522 GFM 10675 Go Video 10744, 10741, 10869, 11044, 11075 GoldStar 10741 Harman/Kardon 11229 Hitachi 10573, 10664 Hiteker 10672 Insignia 10675, 12428, 12596 Integra 11769, 10627, 12147 JVC 10623, 10867, 11164 Kenwood 10490 LG 10591, 10741, 10869 Magnavox 10503, 10539, 10646, 10675, 11354 Marantz 10539, 12414, 12432 Memorex 10695, 11270, 12213 Microsoft 10522, 12083 Mitsubishi 11521 NAD 10741, 12572 Olevia 12331 Onkyo 10503, 11769, 10627, 11627, 12147 Presidian 10675 Proscan 10522 RCA 10522, 11769, 10822, 12213, 12587, 12592, 12594 Rio 10869 Rotel 10623 Samsung 10490, 10573, 10199, 11044, 11075, 12329, 12489 Sansui 10695 Sanyo 10695 Sharp 10630, 10675, 12250 Shinsonic 10533 Sonic Blue 10869 Sony 11633, 10533, 10864, 11033, 11070, 11431, 11516 Sylvania 10675 Symphonic 10675 TCL 12587 Technics 10490 Tivo 11503 Toshiba 10503, 11769, 10695, 11154, 11503, 12006, 12277 Urban Concepts 10503 Viore 12553 Vizio 12563 Vtrek 12587 Xbox 10522, 12083 Yamaha 10490, 10539, 10497, 10817, 12298 Zenith 10503, 10591, 10741, 10869 Brand Code No. Accurian 10675 Apex Digital 11056 Funai 10675 Go Video 10741 JVC 11164 LG 10741 Magnavox 10646, 10675 Panasonic 10490, 11579 Philips 10646 Brand Code No. Pioneer 10631 RCA 10522 Samsung 10490 Sharp 10675 Sony 11033, 11070, 11431 Sylvania 10675 Toshiba 12277 Zenith 10741 DVD recorder / Grabadora de DVD Blu-ray Disc/HD-DVD player/ Reproductor de Blu-ray Disc/HD-DVD Brand Code No. Denon 12258 Insignia 10675, 12428, 12596 Integra 11769, 12147 LG 10741 Magnavox 10675 Marantz 12414, 12432 Microsoft 12083 NAD 12572 Olevia 12331 Onkyo 11769, 12147 Oppo 12545 Panasonic 11641 Brand Code No. Philips 12084, 12434 Pioneer 10142, 12442 RCA 11769 Samsung 10199 Sharp 12250 Sony 11516 Sylvania 10675 Toshiba 11769 Viore 12553 Vizio 12563 Xbox 12083 Yamaha 12298 If your device is not listed, try the Search function (see “Searching for the correct code”). 2 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 3 Enter the manufacturer’s code (01454). The SET indicator flashes three times and turns off.  Operate the device 1 Aim the RM-VZ220 directly at the device. 2 Press the Device Select button for the device you want to operate. 3 Press POWER to turn on the device. 4 Press buttons on the RM-VZ220 to check that they function. See “Remote Button Descriptions” for the functions of buttons for each device. If the RM-VZ220 does not seem to be working…  Check that you have set the correct manufacturer’s code.  Try repeating the setup procedure using another manufacturer’s code (if listed for your device). If you still cannot operate the RM-VZ220 after trying all the listed codes, try the Search function (see “Searching for the correct code”). Notes  If the setting is incomplete, the SET indicator flashes once and the indicators turn off. Start again from the beginning.  If no operations are performed for 10 seconds while setting, the setting will be canceled, and must be restarted.  To cancel the process, press SET any time. The SET indicator turns off. SET POWER Device Select buttons Number buttons The SET indicator lights up. Searching for the correct code You can set the manufacturer’s code using the Search function. 1 Power on the device with its power switch. 2 Aim the RM-VZ220 at the device you want to set. 3 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 4 Enter 9 - 2 - 2 using the number buttons. The SET indicator flashes three times. 5 Press and hold  to start searching. When the device turns off, release the button. If you overshoot the required code, you can search for the next or previous code using the  or  button. 6 Press . The SET indicator flashes three times and turns off. 7 Check if the code number works correctly (see “Remote Button Descriptions”). If you still cannot operate the device, repeat steps to search for another code that works for most functions of your device. Checking the manufacturer’s code you have set 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 2 Enter 9 - 3 - 3 using the number buttons. The SET indicator flashes three times. 3 Press . 4 When the SET indicator starts flashing, count the number of flashes. Short flash(es) indicate which digit (first, second, etc.), followed by long flash(es) to indicate the digit number (i.e., 2 long flashes represent the number 2). “0” is indicated by rapid flashing. Determine the 5-digit code number this way. To recheck, press . 5 Press SET to finish. Clearing the automatic power-on control (Sony devices only) The Device Select buttons are preset to automatically turn on a device when pressed. To cancel the function: 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press , then release both buttons. 2 Enter 9 - 7 - 7 using the number buttons. The SET indicator flashes three times. 3 Press the desired Device Select button. The SET indicator flashes three times and turns off. To set the function again, perform the same procedure above. Restoring the factory settings You can clear all the settings and reset the RM-VZ220 to its factory settings. 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press , then release both buttons. 2 Enter 9 - 0 - 0 using the number buttons. The SET indicator flashes three times. To cancel, press any button except . 3 Press . The SET indicator flashes three times and turns off. Remote Button Descriptions General  SET: Press to set up the RM-VZ220. The indicator lights or flashes while setting.  Device Select buttons: Press to select the device to operate.  GUIDE: Displays the program guide (EPG).  //// : Moves the cursor to select a menu item/enters the selected item.  RETURN: Returns to the previous display/exits the menu.  VOL +/–: Turns the volume up/down.  POWER: Turns the selected device on and off.  MUTING: Mutes the volume. Press again to turn muting off.  SLEEP: Enables the Sleep function (when available). The number 5, CH+, and  buttons each have a tactile dot for ease of use. The GUIDE and RETURN buttons do not work for a VCR. Note on the VOL+/– and MUTING buttons When a TV or other video device is selected, the TV’s volume is controlled. When a DVD Home Theater is selected, its volume can be controlled. TV  : VIDEO 1 input : VIDEO 2 input : HDMI input : RGB input : (PIP INPUT) Changes the input mode of the “window” picture. : (PIP) Turns the “window” picture on and off. : (PIP MOVE) Moves the location of the “window” picture. : (PIP STILL) Freezes the “window” picture. : (PIP SWAP) Switches between “main” and “window” picture.  A: Red button B: Green button C: Yellow button D: Blue button  LIST: (CAPTION) Displays closed captioning.  MENU: Calls up the menu display.  INPUT: Changes the input mode.  1 – 9, 0, ENTER,  (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER).  PAGE +/–: (PIP CH +/–) Changes the channel up/down in the “window” picture.  FAVORITES: Enables the Favorite function.  INFO: Displays program information.  OPTIONS: Displays the options menu.  RECALL: Selects the channel previously selected.  CH +/–: Switches the channel up/ down. Cable set top box/IPTV  : Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). : Proceeds to the next location. : Fast reverses. : Plays. : Fast forwards. : Records. : Pauses. : Stops.  A, B, C buttons D: (Live TV) Displays Master Guide.  LIST: Displays the title of recorded program.  MENU: Calls up the menu display.  INPUT: Changes the input mode.    1 – 9, 0, ENTER,  (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER).  PAGE +/–: Page up/down  FAVORITES: Enables the Favorite function.  INFO: Displays program information.  OPTIONS: Displays the options menu.  RECALL: Switches between the current and previous channel.  CH +/–: Switches the channel up/ down. Satellite receiver  : Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). : Proceeds to the next location. : Fast reverses. : Plays. : Fast forwards. : Records. : Pauses. : Stops.  A: Red button B: Green button C: Yellow button D: Blue button  LIST: Displays the title of recorded program/PVR menu.  MENU: Calls up the menu display.  INPUT: (TV/SAT) Switches the output between SAT and TV.    1 – 9, 0, ENTER,  (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER).  PAGE +/–: Page up/down  FAVORITES: Enables the Favorite function.  INFO: Displays program information.  OPTIONS: Displays the Satellite dish menu/Station Index.  RECALL: Tunes to the last tuned station.  CH +/–: Switches the channel up/ down. VCR  : Rewinds. : Plays. : Fast forwards. : Records. : Pauses. : Stops.  INPUT: Changes the input mode.  1 – 9, 0: Number buttons  : Ejects a tape.  INFO: (DISPLAY) Displays the playback information.  OPTIONS: (ANT/SW) Switches the antenna output.  RECALL: (DRIVE SELECT) Selects the deck.  CH +/–: Switches the channel up/ down.  ENTER: Enters the selected item. DVD player/recorder  : Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). : Skips to the next chapter/ track. : Fast reverses. : Plays. : Fast forwards. : Records (for DVD recorder). : Pauses. : Stops.  A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting.  LIST: Displays the Title List.  MENU: Displays the DVD menu.  INPUT: Changes the input mode.  1 – 9, 0: Number buttons   (dot): (+10) Selects numbers 10 and above.  : Opens/closes the disc tray.  PAGE +: (DVD) Selects the DVD drive. PAGE –: (HDD) Selects the internal HDD (hard disk drive).  FAVORITES: (TOP MENU) Displays the Top Menu.  INFO: (DISPLAY) Displays the playback information.  OPTIONS: Displays the options menu.  RECALL: (DRIVE SELECT) Switches between HDD and DVD.  CH +/–: Switches the channel up/ down (for DVD recorder).  ENTER: Enters the selected item. Blu-ray Disc/HD-DVD player  : Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). : Skips to the next chapter/ track. : Fast reverses. : Plays. : Fast forwards. : Records (for BD recorder). : Pauses. : Stops.  A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting.  MENU: Displays the Pop-up Menu/ Disc Menu.  INPUT: Changes the input mode.  1 – 9, 0: Number buttons   (dot): (+10) Selects numbers 10 and above.  : Opens/closes the disc tray.  PAGE +: (BD) Selects the BD drive. PAGE –: (HDD) Selects the internal HDD (hard disk drive).  FAVORITES: (TOP MENU) Displays the Top Menu.  INFO: (DISPLAY) Displays the playback information.  OPTIONS: Displays the options menu.  ENTER: Enters the selected item. DVR (digital video recorder)/PVR (personal video recorder)  : Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). : Proceeds to the next location. : Fast reverses. : Plays. : Fast forwards. : Records. : Pauses. : Stops.  A: (REPLAY*) Enables the Replay function for DVR/Replay TV. B: (Live TV*) Displays Master Guide.  LIST: Displays the title of recorded program.  MENU: Calls up the menu display.  INPUT: Changes the input mode.  1 – 9, 0: Number buttons   (dot): (+10) Selects numbers 10 and above.  : Opens/closes the disc tray.  PAGE +/–: Page up/down, Thumbs* up/down  INFO: (DISPLAY) Displays the playback information.  RECALL: Selects the channel previously selected.  CH +/–: Switches the channel up/ down.  ENTER: Enters the selected item. * These buttons correspond to TiVo service or the Replay service. Refer to its instruction manual for details. DVD Home Theater  : Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). : Skips to the next chapter/ track. : Fast reverses. : Plays. : Fast forwards. : Records. : Pauses. : Stops.  A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting.  LIST: Enables the SOUND FIELD function.  MENU: Displays the DVD menu.  INPUT: Changes the input mode.  1 – 9, 0: Number buttons   (dot): (+10) Selects numbers 10 and above.  : Opens/closes the disc tray.  FAVORITES: (TOP MENU) Displays the Top Menu.  INFO: (DISPLAY) Displays the playback information.  OPTIONS: Displays the amplifier menu.  RECALL: (BAND) Selects FM/AM.  CH +/–: Presets or tunes frequency up/down.  ENTER: Enters the selected item. Notes on using the RM-VZ220  The RM-VZ220 will not perform functions that the device is not designed for. For example, if your TV does not have the muting function, MUTING on the RM-VZ220 will not function with your TV.  The function of the buttons varies depending on settings/operating modes. The table of “Remote Button Descriptions” shows how the RM-VZ220 generally operates for each device in the preset mode.  If your cable set top box can control volume, be sure to set its volume to a moderate level. If the volume on the cable set top box is turned down completely, you will not be able to adjust your TV’s volume with the RM-VZ220. Manufacturer’s Code List / Lista de códigos del fabricante English The following tables show brand names (Brand) and their corresponding code numbers (Code No.). 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 2 Enter the manufacturer’s code. The SET indicator flashes three times and turns off. Español La siguiente tabla muestra los nombres de las marcas (Brand) y el número de código correspondiente (Code No.). 1 Presione y mantenga presionado el botón SET durante más de 3 segundos. Se encenderá la luz indicadora SET. Mientras tiene presionado el botón SET, presione el botón de selección de dispositivo deseado y luego suelte ambos botones. 2 Ingrese el código del fabricante. El indicador SET parpadeará tres veces y se apagará. Brand Code No. Acer 01339 Action 00650 Admiral 00463 Akai 00812, 01675, 00702, 02232 Akira 01733 AOC 01365, 01589 Apex Digital 00748 Aventura 00171 Bell & Howell 00154 BPL 01543 Broksonic 00463 Carver 00054 Celebrity 00000 Coby 02306, 02345, 02348 Commercial Solutions 01447 Crosley 00054 Curtis 02352 Curtis Mathes 00054, 00154, 00702, 01661 Daewoo 01661 Digital Lifestyles 01765 Durabrand 00463, 00171 Dynex 01463, 01810, 02049 Electroband 00000 Electrograph 01755 Electrohome 00463 Elektra 01661 Element 01687 Emerson 01864, 00154, 00463, 00171, 01661, 01394 Emprex 01765 Envision 01365, 01589 ESA 00812, 00171 Fisher 00154 Funai 00171 Gateway 01755, 01756 GE 01447, 00051, 02359 GFM 00171 Haier 01748, 01749, 02309, 02449 Harman/Kardon 00054 Hisense 00748, 01314, 02098 Hitachi 01643, 02215, 02433 iLo 01684 Infinity 00054 Insignia 01564, 00171, 02049 JBL 00054 JCB 00000 JVC 00731, 01253, 01601, 01774 KDS 01687 Kolin 01331 LG 01423, 02358 LXI 00054, 00154, 00156 MAG 01687 Magnavox 01454, 01866, 00054, 01254, 01365, 02372 Marantz 00054 Matsushita 00650 Maxent 01755 Memorex 00154, 00463, 00150 MGA 00150 Midland 00051 Brand Code No. Mitsubishi 01250, 00150, 00836 NAD 00156 NEC 01797 NetTV 01755 Norcent 00748, 01365, 01589 Olevia 01610, 01144, 01331 Onida 01253, 02396 Optimus 00154, 00650 Orion 00463, 01463 Panasonic 01480, 00051, 00650 PARK 02104 Penney 00156, 00051 Petters 01523 Philco 00054 Philips 01454, 00054, 00690, 01744, 02372 Pioneer 01457, 01260 Polaroid 01523, 01276, 01314, 01687 Portland 01661 Prism 00051 Proscan 01447, 02147, 02256 Proview 01687 Quasar 00051, 00650 RadioShack 00154 RCA 01447, 01781, 02187, 02247, 02403, 02429, 02434 Realistic 00154 Sampo 01755 Samsung 00812, 00702 Sansui 00463 Sanyo 00154, 01142 Sceptre 01360, 01599 Scott 01711 Sears 00054, 00154, 00156, 00171 Sharp 00818 Sony 00810, 00000 Spectroniq 01687 Squareview 00171 Superscan 00864 Supreme 00000 SVA 00748 Sylvania 01864, 00054, 00171, 01314, 01394 Symphonic 00171 Syntax 01610, 01144, 01331 Tatung 01756 TCL 02403, 02429 Technics 00051 Techwood 00051 Teknika 00054, 00150 Telefunken 00702 Toshiba 01524, 00154, 00156, 00650 TVS 00463 Venturer 01865 Videocon 01540, 01541, 02436 Vidikron 00054 Viewsonic 01755, 00864, 00885, 01627, 01742 Viore 01684, 02104, 02352 Vizio 01758, 00864, 00885, 01756 VU 02098 TV / TV Brand Code No. Wards 00054 Waycon 00156 Westinghouse 01712, 00885, 01577 White Westinghouse 00463, 01661 Wyse 01365 Zenith 00463, 01661 Brand Code No. Accurian 10675 Akai 10695 Allegro 10869 Apex Digital 10672, 11056 Bel Canto Design 11571 Broksonic 10695 CineVision 10869 Citizen 10695 CyberHome 11024 Daewoo 10869 Denon 10490, 11634, 12258 Disney 10675, 11270 Emerson 10591, 10675 Enterprise 10591 Funai 10675 GE 10522 GFM 10675 Go Video 10744, 10741, 10869, 11044, 11075 GoldStar 10741 Harman/Kardon 11229 Hitachi 10573, 10664 Hiteker 10672 Insignia 10675, 12428, 12596 Integra 11769, 10627, 12147 JVC 10623, 10867, 11164 Kenwood 10490 LG 10591, 10741, 10869 Magnavox 10503, 10539, 10646, 10675, 11354 Marantz 10539, 12414, 12432 Memorex 10695, 11270, 12213 Microsoft 10522, 12083 Mitsubishi 11521 NAD 10741, 12572 Olevia 12331 Onkyo 10503, 11769, 10627, 11627, 12147 Brand Code No. Oppo 10575, 12545 Panasonic 10490, 11579, 11641 Philco 10675 Philips 10503, 10539, 12056, 12084, 10646, 10675, 11267, 11354, 12434 Pioneer 10142, 10631, 11571, 12442 Polk Audio 10539 Presidian 10675 Proscan 10522 RCA 10522, 11769, 10822, 12213, 12587, 12592, 12594 Rio 10869 Rotel 10623 Samsung 10490, 10573, 10199, 11044, 11075, 12329, 12489 Sansui 10695 Sanyo 10695 Sharp 10630, 10675, 12250 Shinsonic 10533 Sonic Blue 10869 Sony 11633, 10533, 10864, 11033, 11070, 11431, 11516 Sylvania 10675 Symphonic 10675 TCL 12587 Technics 10490 Tivo 11503 Toshiba 10503, 11769, 10695, 11154, 11503, 12006, 12277 Urban Concepts 10503 Viore 12553 Vizio 12563 Vtrek 12587 Xbox 10522, 12083 Yamaha 10490, 10539, 10497, 10817, 12298 Zenith 10503, 10591, 10741, 10869 DVD player / Reproductor de DVD Brand Code No. Accurian 10675 Apex Digital 11056 Funai 10675 Go Video 10741 JVC 11164 LG 10741 Magnavox 10646, 10675 Panasonic 10490, 11579 Philips 10646 Brand Code No. Pioneer 10631 RCA 10522 Samsung 10490 Sharp 10675 Sony 11033, 11070, 11431 Sylvania 10675 Toshiba 12277 Zenith 10741 DVD recorder / Grabadora de DVD Blu-ray Disc/HD-DVD player/ Reproductor de Blu-ray Disc/HD-DVD Brand Code No. Denon 12258 Insignia 10675, 12428, 12596 Integra 11769, 12147 LG 10741 Magnavox 10675 Marantz 12414, 12432 Microsoft 12083 NAD 12572 Olevia 12331 Onkyo 11769, 12147 Oppo 12545 Panasonic 11641 Brand Code No. Philips 12084, 12434 Pioneer 10142, 12442 RCA 11769 Samsung 10199 Sharp 12250 Sony 11516 Sylvania 10675 Toshiba 11769 Viore 12553 Vizio 12563 Xbox 12083 Yamaha 12298

4-170-642-12(1) Remote Commander RM-VZ220 ©2010 Sony Corporation Printed in China Operating Instructions Manual de instrucciones (parte posterior) English For the Customers in the U.S.A. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Setting Up the RM-VZ220 The RM-VZ220 is preset at the factory to operate Sony brand video devices set to any of the Device Select buttons (see the table below). To use with non-Sony devices, or Sony devices that are not preset at the factory, set the manufacturer’s code for each device. Devices Button Factory setting* TV TV Sony TV (00810) TV, Cable set top box, Satellite receiver, IPTV, DVD player, DVD recorder, Blu-ray Disc player, DVR (digital video recorder), PVR (personal video recorder), VCR, DVD Home Theater CBL (SAT) Cable set top box (non- Sony) (51376) VCR Sony VCR (60032) DVD Sony DVD player (11033) * The five-digit code is the preset manufacturer’s code. Note Only a TV can be assigned to the TV Device Select button. You can assign any device to the other Device Select buttons. Installing the batteries Slide open the battery compartment and insert two size AA (R6) dry batteries (not supplied). Insert the batteries (negative end first) through the guide clamp within each compartment as shown below. 1 2 Battery life Under normal conditions, size AA (LR6) alkaline batteries will last up to one year. If the RM-VZ220 does not operate properly, the batteries might be drained. Replace both batteries with new ones. Notes  Replace the batteries within 2 minutes after removing them, and do not press any button when replacing the batteries. Otherwise, your code settings may be cleared.  Do not use an old battery with a new one, or mix different types of batteries together.  If the electrolyte inside the battery should leak, wipe the contaminated area of the battery compartment with a cloth and replace the old batteries with new ones. To prevent electrolyte from leaking, remove the batteries when you plan not to use the RM-VZ220 for a long period of time. Specifications Operating distance Approx. 11 m (36 ft) (varies depending on devices of different manufacturers) Power requirements Two size AA (R6) dry batteries (not supplied) Battery life Approx. 1 year when using size AA (LR6) alkaline batteries (varies depending on frequency of button use - up to approx. 300 times per day.) Dimensions Approx. 53 × 213 × 27 mm (2 1/8 × 8 1/2 × 1 1/8 in.) (w/h/d) Mass Approx. 100 g (3.5 oz) (not including batteries) Design and specifications are subject to change without notice. Troubleshooting If you have problems setting up or using the RM-VZ220:  Carefully perform the setup procedure of “Startup Guide.” If the RM-VZ220 does not work, try repeating the setup procedure using another manufacturer’s code (if listed for your device). If you still cannot operate the RM-VZ220, try the Search function (see “Searching for the correct code”).  Aim the RM-VZ220 directly at the device.  Remove any obstacles in the path between the RM-VZ220 and the device.  Make sure you have pressed the correct Device Select button.  Check that the device has infrared remote capability. For example, if your device did not come with a remote control, it probably is not capable of being controlled by the RM-VZ220.  The batteries are weak, or not inserted correctly. Replace them with new ones or insert them correctly. For the customers in the U.S.A. Customer Support Information After you have read through this manual, if you still cannot get the RM-VZ220 to work properly, call the Sony Customer Support Helpline at 1-800-822-2217.

4-170-642-12(1) Remote Commander RM-VZ220 ©2010 Sony Corporation Printed in China Operating Instructions Manual de instrucciones (parte posterior) English For the Customers in the U.S.A. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ��Reorient or relocate the receiving antenna. ��Increase the separation between the equipment and receiver. ��Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ��Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Setting Up the RM-VZ220 The RM-VZ220 is preset at the factory to operate Sony brand video devices set to any of the Device Select buttons (see the table below). To use with non-Sony devices, or Sony devices that are not preset at the factory, set the manufacturer’s code for each device. Devices Button Factory setting* TV TV Sony TV (00810) TV, Cable set top box, Satellite receiver, IPTV, DVD player, DVD recorder, Blu-ray Disc player, DVR (digital video recorder), PVR (personal video recorder), VCR, DVD Home Theater CBL (SAT) Cable set top box (non- Sony) (51376) VCR Sony VCR (60032) DVD Sony DVD player (11033) * The five-digit code is the preset manufacturer’s code. Note Only a TV can be assigned to the TV Device Select button. You can assign any device to the other Device Select buttons. Installing the batteries Slide open the battery compartment and insert two size AA (R6) dry batteries (not supplied). Insert the batteries (negative end first) through the guide clamp within each compartment as shown below. 1 2 Battery life Under normal conditions, size AA (LR6) alkaline batteries will last up to one year. If the RM-VZ220 does not operate properly, the batteries might be drained. Replace both batteries with new ones. Notes ��Replace the batteries within 2 minutes after removing them, and do not press any button when replacing the batteries. Otherwise, your code settings may be cleared. ��Do not use an old battery with a new one, or mix different types of batteries together. ��If the electrolyte inside the battery should leak, wipe the contaminated area of the battery compartment with a cloth and replace the old batteries with new ones. To prevent electrolyte from leaking, remove the batteries when you plan not to use the RM-VZ220 for a long period of time. Specifications Operating distance Approx. 11 m (36 ft) (varies depending on devices of different manufacturers) Power requirements Two size AA (R6) dry batteries (not supplied) Battery life Approx. 1 year when using size AA (LR6) alkaline batteries (varies depending on frequency of button use - up to approx. 300 times per day.) Dimensions Approx. 53 × 213 × 27 mm (2 1/8 × 8 1/2 × 1 1/8 in.) (w/h/d) Mass Approx. 100 g (3.5 oz) (not including batteries) Design and specifications are subject to change without notice. Troubleshooting If you have problems setting up or using the RM-VZ220: ��Carefully perform the setup procedure of “Startup Guide.” If the RM-VZ220 does not work, try repeating the setup procedure using another manufacturer’s code (if listed for your device). If you still cannot operate the RM-VZ220, try the Search function (see “Searching for the correct code”). ��Aim the RM-VZ220 directly at the device. ��Remove any obstacles in the path between the RM-VZ220 and the device. ��Make sure you have pressed the correct Device Select button. ��Check that the device has infrared remote capability. For example, if your device did not come with a remote control, it probably is not capable of being controlled by the RM-VZ220. ��The batteries are weak, or not inserted correctly. Replace them with new ones or insert them correctly. For the customers in the U.S.A. Customer Support Information After you have read through this manual, if you still cannot get the RM-VZ220 to work properly, call the Sony Customer Support Helpline at 1-800-822-2217. Sta RM-VZ220_U [US,ES] 4-170-642-12(1) 4-170-642-12(1) Remote Commander RM-VZ220 ©2010 Sony Corporation Printed in China Operating Instructions Manual de instrucciones (parte posterior) English For the Customers in the U.S.A. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: � Reorient or relocate the receiving antenna. � Increase the separation between the equipment and receiver. � Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. � Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Setting Up the RM-VZ220 The RM-VZ220 is preset at the factory to operate Sony brand video devices set to any of the Device Select buttons (see the table below). To use with non-Sony devices, or Sony devices that are not preset at the factory, set the manufacturer’s code for each device. Devices Button Factory setting* TV TV Sony TV (00810) TV, Cable set top box, Satellite receiver, IPTV, DVD player, DVD recorder, Blu-ray Disc player, DVR (digital video recorder), PVR (personal video recorder), VCR, DVD Home Theater CBL (SAT) Cable set top box (non- Sony) (51376) VCR Sony VCR (60032) DVD Sony DVD player (11033) * The five-digit code is the preset manufacturer’s code. Note Only a TV can be assigned to the TV Device Select button. You can assign any device to the other Device Select buttons. Installing the batteries Slide open the battery compartment and insert two size AA (R6) dry batteries (not supplied). Insert the batteries (negative end first) through the guide clamp within each compartment as shown below. 1 2 Battery life Under normal conditions, size AA (LR6) alkaline batteries will last up to one year. If the RM-VZ220 does not operate properly, the batteries might be drained. Replace both batteries with new ones. Notes � Replace the batteries within 2 minutes after removing them, and do not press any button when replacing the batteries. Otherwise, your code settings may be cleared. � Do not use an old battery with a new one, or mix different types of batteries together. � If the electrolyte inside the battery should leak, wipe the contaminated area of the battery compartment with a cloth and replace the old batteries with new ones. To prevent electrolyte from leaking, remove the batteries when you plan not to use the RM-VZ220 for a long period of time. Specifications Operating distance Approx. 11 m (36 ft) (varies depending on devices of different manufacturers) Power requirements Two size AA (R6) dry batteries (not supplied) Battery life Approx. 1 year when using size AA (LR6) alkaline batteries (varies depending on frequency of button use - up to approx. 300 times per day.) Dimensions Approx. 53 × 213 × 27 mm (2 1/8 × 8 1/2 × 1 1/8 in.) (w/h/d) Mass Approx. 100 g (3.5 oz) (not including batteries) Design and specifications are subject to change without notice. Troubleshooting If you have problems setting up or using the RM-VZ220: � Carefully perform the setup procedure of “Startup Guide.” If the RM-VZ220 does not work, try repeating the setup procedure using another manufacturer’s code (if listed for your device). If you still cannot operate the RM-VZ220, try the Search function (see “Searching for the correct code”). � Aim the RM-VZ220 directly at the device. � Remove any obstacles in the path between the RM-VZ220 and the device. � Make sure you have pressed the correct Device Select button. � Check that the device has infrared remote capability. For example, if your device did not come with a remote control, it probably is not capable of being controlled by the RM-VZ220. � The batteries are weak, or not inserted correctly. Replace them with new ones or insert them correctly. For the customers in the U.S.A. Customer Support Information After you have read through this manual, if you still cannot get the RM-VZ220 to work properly, call the Sony Customer Support Helpline at 1-800-822-2217. Startup Guide This guide shows you how to set up and use the RM-VZ220 to operate your devices. If your Sony device has already been preset, see “Operate the device.” Set the manufacturer’s code Example: To set up a Philips TV 1 Find the manufacturer’s code in “Manufacturer’s Code List.” Manufacturer’s Code List / Lista de códigos del fabricante English The following tables show brand names (Brand) and their corresponding code numbers (Code No.). 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 2 Enter the manufacturer’s code. The SET indicator flashes three times and turns off. Español La siguiente tabla muestra los nombres de las marcas (Brand) y el número de código correspondiente (Code No.). 1 Presione y mantenga presionado el botón SET durante más de 3 segundos. Se encenderá la luz indicadora SET. Mientras tiene presionado el botón SET, presione el botón de selección de dispositivo deseado y luego suelte ambos botones. 2 Ingrese el código del fabricante. El indicador SET parpadeará tres veces y se apagará. Brand Code No. Sony 00810, 00000 Acer 01339 Action 00650 Admiral 00463 Akai 00812, 01675, 00702, 02232 Akira 01733 AOC 01365, 01589 Apex Digital 00748 Aventura 00171 Bell & Howell 00154 BPL 01543 Broksonic 00463 Carver 00054 Celebrity 00000 Coby 02306, 02345, 02348 Commercial Solutions 01447 Crosley 00054 Curtis 02352 Curtis Mathes 00054, 00154, 00702, 01661 Daewoo 01661 Digital Lifestyles 01765 Durabrand 00463, 00171 Dynex 01463, 01810, 02049 Electroband 00000 Electrograph 01755 Electrohome 00463 Elektra 01661 Element 01687 Emerson 01864, 00154, 00463, 00171, 01661, 01394 Emprex 01765 Envision 01365, 01589 ESA 00812, 00171 Fisher 00154 Funai 00171 Gateway 01755, 01756 GE 01447, 00051, 02359 GFM 00171 Haier 01748, 01749, 02309, 02449 Harman/Kardon 00054 Hisense 00748, 01314, 02098 Hitachi 01643, 02215, 02433 iLo 01684 Infinity 00054 Insignia 01564, 00171, 02049 JBL 00054 JCB 00000 JVC 00731, 01253, 01601, 01774 KDS 01687 Kolin 01331 LG 01423, 02358 LXI 00054, 00154, 00156 MAG 01687 Magnavox 01454, 01866, 00054, 01254, 01365, 02372 Marantz 00054 Matsushita 00650 Maxent 01755 Memorex 00154, 00463, 00150 MGA 00150 Brand Code No. Midland 00051 Mitsubishi 01250, 00150, 00836 NAD 00156 NEC 01797 NetTV 01755 Norcent 00748, 01365, 01589 Olevia 01610, 01144, 01331 Onida 01253, 02396 Optimus 00154, 00650 Orion 00463, 01463 Panasonic 01480, 00051, 00650 PARK 02104 Penney 00156, 00051 Petters 01523 Philco 00054 Philips 01454, 00054, 00690, 01744, 02372 Pioneer 01457, 01260 Polaroid 01523, 01276, 01314, 01687 Portland 01661 Prism 00051 Proscan 01447, 02147, 02256 Proview 01687 Quasar 00051, 00650 RadioShack 00154 RCA 01447, 01781, 02187, 02247, 02403, 02429, 02434 Realistic 00154 Sampo 01755 Samsung 00812, 00702 Sansui 00463 Sanyo 00154, 01142 Sceptre 01360, 01599 Scott 01711 Sears 00054, 00154, 00156, 00171 Sharp 00818 Spectroniq 01687 Squareview 00171 Superscan 00864 Supreme 00000 SVA 00748 Sylvania 01864, 00054, 00171, 01314, 01394 Symphonic 00171 Syntax 01610, 01144, 01331 Tatung 01756 TCL 02403, 02429 Technics 00051 Techwood 00051 Teknika 00054, 00150 Telefunken 00702 Toshiba 01524, 00154, 00156, 00650 TVS 00463 Venturer 01865 Videocon 01540, 01541, 02436 Vidikron 00054 Viewsonic 01755, 00864, 00885, 01627, 01742 Viore 01684, 02104, 02352 Vizio 01758, 00864, 00885, 01756 VU 02098 TV / TV Brand Code No. Wards 00054 Waycon 00156 Westinghouse 01712, 00885, 01577 White Westinghouse 00463, 01661 Wyse 01365 Zenith 00463, 01661 Brand Code No. Sony 11633, 10533, 10864, 11033, 11070, 11431, 11516 Accurian 10675 Akai 10695 Allegro 10869 Apex Digital 10672, 11056 Bel Canto Design 11571 Broksonic 10695 CineVision 10869 Citizen 10695 CyberHome 11024 Daewoo 10869 Denon 10490, 11634, 12258 Disney 10675, 11270 Emerson 10591, 10675 Enterprise 10591 Funai 10675 GE 10522 GFM 10675 Go Video 10744, 10741, 10869, 11044, 11075 GoldStar 10741 Harman/Kardon 11229 Hitachi 10573, 10664 Hiteker 10672 Insignia 10675, 12428, 12596 Integra 11769, 10627, 12147 JVC 10623, 10867, 11164 Kenwood 10490 LG 10591, 10741, 10869 Magnavox 10503, 10539, 10646, 10675, 11354 Marantz 10539, 12414, 12432 Memorex 10695, 11270, 12213 Microsoft 10522, 12083 Mitsubishi 11521 NAD 10741, 12572 Olevia 12331 Brand Code No. Onkyo 10503, 11769, 10627, 11627, 12147 Oppo 10575, 12545 Panasonic 10490, 11579, 11641 Philco 10675 Philips 10503, 10539, 12056, 12084, 10646, 10675, 11267, 11354, 12434 Pioneer 10142, 10631, 11571, 12442 Polk Audio 10539 Presidian 10675 Proscan 10522 RCA 10522, 11769, 10822, 12213, 12587, 12592, 12594 Rio 10869 Rotel 10623 Samsung 10490, 10573, 10199, 11044, 11075, 12329, 12489 Sansui 10695 Sanyo 10695 Sharp 10630, 10675, 12250 Shinsonic 10533 Sonic Blue 10869 Sylvania 10675 Symphonic 10675 TCL 12587 Technics 10490 Tivo 11503 Toshiba 10503, 11769, 10695, 11154, 11503, 12006, 12277 Urban Concepts 10503 Viore 12553 Vizio 12563 Vtrek 12587 Xbox 10522, 12083 Yamaha 10490, 10539, 10497, 10817, 12298 Zenith 10503, 10591, 10741, 10869 DVD player / Reproductor de DVD Brand Code No. Sony 11033, 11070, 11431 Accurian 10675 Apex Digital 11056 Funai 10675 Go Video 10741 JVC 11164 LG 10741 Magnavox 10646, 10675 Panasonic 10490, 11579 Brand Code No. Philips 10646 Pioneer 10631 RCA 10522 Samsung 10490 Sharp 10675 Sylvania 10675 Toshiba 12277 Zenith 10741 DVD recorder / Grabadora de DVD Blu-ray Disc/HD-DVD player/ Reproductor de Blu-ray Disc/HD-DVD Brand Code No. Sony 11516 Denon 12258 Insignia 10675, 12428, 12596 Integra 11769, 12147 LG 10741 Magnavox 10675 Marantz 12414, 12432 Microsoft 12083 NAD 12572 Olevia 12331 Onkyo 11769, 12147 Oppo 12545 Brand Code No. Panasonic 11641 Philips 12084, 12434 Pioneer 10142, 12442 RCA 11769 Samsung 10199 Sharp 12250 Sylvania 10675 Toshiba 11769 Viore 12553 Vizio 12563 Xbox 12083 Yamaha 12298 Brand Code No. Sony 00810, 00000 Acer 01339 Action 00650 Brand Code No. Midland 00051 Mitsubishi 01250, 00150, 00836 NAD 00156 TV / TV BPL 01543 Broksonic 00463 Carver 00054 Celebrity 00000 Coby 02306, 02345, 02348 Commercial Solutions 01447 Crosley 00054 Curtis 02352 Curtis Mathes 00054, 00154, 00702, 01661 Daewoo 01661 Digital Lifestyles 01765 Durabrand 00463, 00171 Panasonic 01480, 00051, 00650 PARK 02104 Penney 00156, 00051 Petters 01523 Philco 00054 Philips 01454, 00054, 00690, 01744, 02372 Pioneer 01457, 01260 Polaroid 01523, 01276, 01314, 01687 Portland 01661 Prism 00051 Proscan 01447, 02147, 02256 Proview 01687 If your device is not listed, try the Search function (see “Searching for the correct code”). 2 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 3 Enter the manufacturer’s code (01454). The SET indicator flashes three times and turns off. � Operate the device 1 Aim the RM-VZ220 directly at the device. 2 Press the Device Select button for the device you want to operate. 3 Press POWER to turn on the device. 4 Press buttons on the RM-VZ220 to check that they function. See “Remote Button Descriptions” for the functions of buttons for each device. If the RM-VZ220 does not seem to be working… � Check that you have set the correct manufacturer’s code. � Try repeating the setup procedure using another manufacturer’s code (if listed for your device). If you still cannot operate the RM-VZ220 after trying all the listed codes, try the Search function (see “Searching for the correct code”). Notes � If the setting is incomplete, the SET indicator flashes once and the indicators turn off. Start again from the beginning. � If no operations are performed for 10 seconds while setting, the setting will be canceled, and must be restarted. � To cancel the process, press SET any time. The SET indicator turns off. SET POWER Device Select buttons Number buttons The SET indicator lights up. Searching for the correct code You can set the manufacturer’s code using the Search function. 1 Power on the device with its power switch. 2 Aim the RM-VZ220 at the device you want to set. 3 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 4 Enter 9 - 2 - 2 using the number buttons. The SET indicator flashes three times. 5 Press and hold � to start searching. When the device turns off, release the button. If you overshoot the required code, you can search for the next or previous code using the � or � button. 6 Press . The SET indicator flashes three times and turns off. 7 Check if the code number works correctly (see “Remote Button Descriptions”). If you still cannot operate the device, repeat steps to search for another code that works for most functions of your device. Checking the manufacturer’s code you have set 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press the desired Device Select button, then release both buttons. 2 Enter 9 - 3 - 3 using the number buttons. The SET indicator flashes three times. 3 Press �. 4 When the SET indicator starts flashing, count the number of flashes. Short flash(es) indicate which digit (first, second, etc.), followed by long flash(es) to indicate the digit number (i.e., 2 long flashes represent the number 2). “0” is indicated by rapid flashing. Determine the 5-digit code number this way. To recheck, press �. 5 Press SET to finish. Clearing the automatic power-on control (Sony devices only) The Device Select buttons are preset to automatically turn on a device when pressed. To cancel the function: 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press , then release both buttons. 2 Enter 9 - 7 - 7 using the number buttons. The SET indicator flashes three times. 3 Press the desired Device Select button. The SET indicator flashes three times and turns off. To set the function again, perform the same procedure above. Restoring the factory settings You can clear all the settings and reset the RM-VZ220 to its factory settings. 1 Press and hold SET for more than 3 seconds. The SET indicator lights up. While keeping SET held down, press , then release both buttons. 2 Enter 9 - 0 - 0 using the number buttons. The SET indicator flashes three times. To cancel, press any button except . 3 Press . The SET indicator flashes three times and turns off. Remote Button D General �� SET: Press to set up the RM setting. � Device Select buttons: Press � GUIDE: Displays the program g � �/�/�/�/ : Moves the cursor � RETURN: Returns to the previo � VOL +/–: Turns the volume up/ � POWER: Turns the selected dev � MUTING: Mutes the volume. P � SLEEP: Enables the Sleep funct The number 5, CH+, and � buttons The GUIDE and RETURN buttons do Note on the VOL+/– and MUTIN When a TV or other video device is se DVD Home Theater is selected, its vo TV � �: VIDEO 1 input : VIDEO 2 input : HDMI input �: RGB input �: (PIP INPUT) Changes th input mode of the “window” picture. �: (PIP) Turns the “window” picture on and off. �: (PIP MOVE) Moves the location of the “window” pictur �: (PIP STILL) Freezes the “window” picture. �: (PIP SWAP) Switches betwe “main” and “window” picture. � A: Red button B: Green button C: Yellow button D: Blue button � LIST: (CAPTION) Displays clo captioning. elease both buttons. 9 - 2 - 2 using the number buttons. ET indicator flashes three times. and hold � to start searching. the device turns off, release the button. overshoot the required code, you can search for the next or previous sing the � or � button. . ET indicator flashes three times and turns off. if the code number works correctly (see “Remote Button ptions”). still cannot operate the device, repeat steps to search for another hat works for most functions of your device. king the manufacturer’s code you have set and hold SET for more than 3 seconds. ET indicator lights up. keeping SET held down, press the desired Device Select button, elease both buttons. 9 - 3 - 3 using the number buttons. ET indicator flashes three times. �. the SET indicator starts flashing, count the number of flashes. flash(es) indicate which digit (first, second, etc.), followed by long s) to indicate the digit number (i.e., 2 long flashes represent the er 2). “0” is indicated by rapid flashing. mine the 5-digit code number this way. To recheck, press �. SET to finish. ng the automatic power-on control (Sony es only) ice Select buttons are preset to automatically turn on a device when l the function: and hold SET for more than 3 seconds. ET indicator lights up. keeping SET held down, press , then release both buttons. 9 - 7 - 7 using the number buttons. ET indicator flashes three times. he desired Device Select button. ET indicator flashes three times and turns off. e function again, perform the same procedure above. ring the factory settings clear all the settings and reset the RM-VZ220 to its factory settings. and hold SET for more than 3 seconds. ET indicator lights up. keeping SET held down, press , then release both buttons. 9 - 0 - 0 using the number buttons. ET indicator flashes three times. cel, press any button except . . ET indicator flashes three times and turns off. General �� SET: Press to set up the RM-VZ220. The indicator lights or flashes while setting. � Device Select buttons: Press to select the device to operate. � GUIDE: Displays the program guide (EPG). � �/�/�/�/ : Moves the cursor to select a menu item/enters the selected item. � RETURN: Returns to the previous display/exits the menu. � VOL +/–: Turns the volume up/down. � POWER: Turns the selected device on and off. � MUTING: Mutes the volume. Press again to turn muting off. � SLEEP: Enables the Sleep function (when available). The number 5, CH+, and � buttons each have a tactile dot for ease of use. The GUIDE and RETURN buttons do not work for a VCR. Note on the VOL+/– and MUTING buttons When a TV or other video device is selected, the TV’s volume is controlled. When a DVD Home Theater is selected, its volume can be controlled. TV � �: VIDEO 1 input : VIDEO 2 input : HDMI input �: RGB input �: (PIP INPUT) Changes the input mode of the “window” picture. �: (PIP) Turns the “window” picture on and off. �: (PIP MOVE) Moves the location of the “window” picture. �: (PIP STILL) Freezes the “window” picture. �: (PIP SWAP) Switches between “main” and “window” picture. � A: Red button B: Green button C: Yellow button D: Blue button � LIST: (CAPTION) Displays closed captioning. � MENU: Calls up the menu display. � INPUT: Changes the input mode. ��� 1 – 9, 0, ENTER, � (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). � PAGE +/–: (PIP CH +/–) Changes the channel up/down in the “window” picture. � FAVORITES: Enables the Favorite function. � INFO: Displays program information. � OPTIONS: Displays the options menu. � RECALL: Selects the channel previously selected. � CH +/–: Switches the channel up/ down. �: Plays. �: Fast forwards. �: Records. �: Pauses. �: Stops. � A, B, C buttons D: (Live TV) Displays Master Guide. � LIST: Displays the title of recorded program. function. � INFO: Displays program information. � OPTIONS: Displays the options menu. � RECALL: Switches between the current and previous channel. � CH +/–: Switches the channel up/ down. Satellite receiver � �: Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). �: Proceeds to the next location. �: Fast reverses. �: Plays. �: Fast forwards. �: Records. �: Pauses. �: Stops. � A: Red button B: Green button C: Yellow button D: Blue button � LIST: Displays the title of recorded program/PVR menu. � MENU: Calls up the menu display. � INPUT: (TV/SAT) Switches the output between SAT and TV. � � � 1 – 9, 0, ENTER, � (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). � PAGE +/–: Page up/down � FAVORITES: Enables the Favorite function. � INFO: Displays program information. � OPTIONS: Displays the Satellite dish menu/Station Index. � RECALL: Tunes to the last tuned station. � CH +/–: Switches the channel up/ down. VCR � �: Rewinds. �: Plays. �: Fast forwards. �: Records. �: Pauses. �: Stops. � INPUT: Changes the input mode. � 1 – 9, 0: Number buttons � �: Ejects a tape. � INFO: (DISPLAY) Displays the playback information. � OPTIONS: (ANT/SW) Switches the antenna output. � RECALL: (DRIVE SELECT) Selects the deck. � CH +/–: Switches the channel up/ down. � ENTER: Enters the selected item. DVD player/recorder � �: Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). �: Skips to the next chapter/ track. �: Fast reverses. �: Plays. �: Fast forwards. �: Records (for DVD recorder). �: Pauses. �: Stops. � A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. � LIST: Displays the Title List. � MENU: Displays the DVD menu. � INPUT: Changes the input mode. � 1 – 9, 0: Number buttons � � (dot): (+10) Selects numbers 10 and above. � �: Opens/closes the disc tray. � PAGE +: (DVD) Selects the DVD drive. PAGE –: (HDD) Selects the internal HDD (hard disk drive). � FAVORITES: (TOP MENU) Displays the Top Menu. � INFO: (DISPLAY) Displays the playback information. � OPTIONS: Displays the options menu. � RECALL: (DRIVE SELECT) Switches between HDD and DVD. � CH +/–: Switches the channel up/ down (for DVD recorder). � ENTER: Enters the selected item. overshoot the required code, you can search for the next or previous sing the � or � button. . ET indicator flashes three times and turns off. if the code number works correctly (see “Remote Button ptions”). still cannot operate the device, repeat steps to search for another hat works for most functions of your device. king the manufacturer’s code you have set and hold SET for more than 3 seconds. ET indicator lights up. keeping SET held down, press the desired Device Select button, elease both buttons. 9 - 3 - 3 using the number buttons. ET indicator flashes three times. �. the SET indicator starts flashing, count the number of flashes. flash(es) indicate which digit (first, second, etc.), followed by long s) to indicate the digit number (i.e., 2 long flashes represent the er 2). “0” is indicated by rapid flashing. mine the 5-digit code number this way. To recheck, press �. SET to finish. ng the automatic power-on control (Sony es only) ice Select buttons are preset to automatically turn on a device when l the function: and hold SET for more than 3 seconds. ET indicator lights up. keeping SET held down, press , then release both buttons. 9 - 7 - 7 using the number buttons. ET indicator flashes three times. he desired Device Select button. ET indicator flashes three times and turns off. e function again, perform the same procedure above. ring the factory settings clear all the settings and reset the RM-VZ220 to its factory settings. and hold SET for more than 3 seconds. ET indicator lights up. keeping SET held down, press , then release both buttons. 9 - 0 - 0 using the number buttons. ET indicator flashes three times. cel, press any button except . . ET indicator flashes three times and turns off. General �� SET: Press to set up the RM-VZ220. The indicator lights or flashes while setting. � Device Select buttons: Press to select the device to operate. � GUIDE: Displays the program guide (EPG). � �/�/�/�/ : Moves the cursor to select a menu item/enters the selected item. � RETURN: Returns to the previous display/exits the menu. � VOL +/–: Turns the volume up/down. � POWER: Turns the selected device on and off. � MUTING: Mutes the volume. Press again to turn muting off. � SLEEP: Enables the Sleep function (when available). The number 5, CH+, and � buttons each have a tactile dot for ease of use. The GUIDE and RETURN buttons do not work for a VCR. Note on the VOL+/– and MUTING buttons When a TV or other video device is selected, the TV’s volume is controlled. When a DVD Home Theater is selected, its volume can be controlled. TV � �: VIDEO 1 input : VIDEO 2 input : HDMI input �: RGB input �: (PIP INPUT) Changes the input mode of the “window” picture. �: (PIP) Turns the “window” picture on and off. �: (PIP MOVE) Moves the location of the “window” picture. �: (PIP STILL) Freezes the “window” picture. �: (PIP SWAP) Switches between “main” and “window” picture. � A: Red button B: Green button C: Yellow button D: Blue button � LIST: (CAPTION) Displays closed captioning. � MENU: Calls up the menu display. � INPUT: Changes the input mode. ��� 1 – 9, 0, ENTER, � (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). � PAGE +/–: (PIP CH +/–) Changes the channel up/down in the “window” picture. � FAVORITES: Enables the Favorite function. � INFO: Displays program information. � OPTIONS: Displays the options menu. � RECALL: Selects the channel previously selected. � CH +/–: Switches the channel up/ down. p y Guide. � LIST: Displays the title of recorded program. p � CH +/–: Switches the channel up/ down. Satellite receiver � �: Proceeds to the previous location. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). �: Proceeds to the next location. �: Fast reverses. �: Plays. �: Fast forwards. �: Records. �: Pauses. �: Stops. � A: Red button B: Green button C: Yellow button D: Blue button � LIST: Displays the title of recorded program/PVR menu. � MENU: Calls up the menu display. � INPUT: (TV/SAT) Switches the output between SAT and TV. � � � 1 – 9, 0, ENTER, � (dot): Changes the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). � PAGE +/–: Page up/down � FAVORITES: Enables the Favorite function. � INFO: Displays program information. � OPTIONS: Displays the Satellite dish menu/Station Index. � RECALL: Tunes to the last tuned station. � CH +/–: Switches the channel up/ down. VCR � �: Rewinds. �: Plays. �: Fast forwards. �: Records. �: Pauses. �: Stops. � INPUT: Changes the input mode. � 1 – 9, 0: Number buttons � �: Ejects a tape. � INFO: (DISPLAY) Displays the playback information. � OPTIONS: (ANT/SW) Switches the antenna output. � RECALL: (DRIVE SELECT) Selects the deck. � CH +/–: Switches the channel up/ down. � ENTER: Enters the selected item. DVD player/recorder � �: Skips to the previous chapter/track. : Briefly replays the scene (Flash –). : Briefly fast forwards the scene (Flash +). �: Skips to the next chapter/ track. �: Fast reverses. �: Plays. �: Fast forwards. �: Records (for DVD recorder). �: Pauses. �: Stops. � A: (SET UP) Calls up the system/ setup menu. B: (SUBTITLE) Switches the subtitle. C: (AUDIO) Changes the sound. D: (CLEAR) Clears the setting. � LIST: Displays the Title List. � MENU: Displays the DVD menu. � INPUT: Changes the input mode. � 1 – 9, 0: Number buttons � � (dot): (+10) Selects numbers 10 and above. � �: Opens/closes the disc tray. � PAGE +: (DVD) Selects the DVD drive. PAGE –: (HDD) Selects the internal HDD (hard disk drive). � FAVORITES: (TOP MENU) Displays the Top Menu. � INFO: (DISPLAY) Displays the playback information. � OPTIONS: Displays the options menu. � RECALL: (DRIVE SELECT) Switches between HDD and DVD. � CH +/–: Switches the channel up/ down (for DVD recorder). � ENTER: Enters the selected item. Not ��If t the an Sta be ��If n pe wh be res ��To SE ind Provided by www.replacementremotes.com