Steelcase 3200 Series Manuals

Steelcase, Inc. Grand Rapids, MI 49501 U.S.A. 1-888-783-3522 Tools Assembly Directions Printed In U.S.A. REV 93-9501180 A Page 1 of 6 Replacement of Standard Legs with Adjustable Legs for Desk & Table Units 3200 & 4200 Series; also 2900 Series Tables 6" Extension 3/8" & 5/16" Sockets 3/16" Allen Wrench Magnetic Tip Section 1 3200 & 4200 Desks Section 2 2900, 3200 & 4200 Tables Assembly Directions 93-9501180 REV A Page 2 of 6 Section 1: 3200 & 4200 Desks • NON-PEDESTAL SIDE 1. Turn desk up-side down. NOTE: When removing file drawers from pedestal, the cradle assembly must be removed with the drawer at the same time. Store drawer on the front face to prevent grease damage on carpet etc. 2a. For 45" desks with center drawer. Remove the center drawer rail, which is attached to the end panel by (3) phillips screws. 2b. For desks larger than 45" with center drawer. Remove filler, (3) phillips screws, (1) attaching end panel and (2) attaching filler to center drawer support. Pull filler forward to clear attaching clips. Center Drawer Rail Desk Filler Assembly Directions 93-9501180 REV A Page 3 of 6 NOTE: Model No. 32F DAL-DBL includes adjustable legs for a double pedestal desk. (2) legs have (3) phillips head screws and (2) legs have 5/16" hex head screws. Model No. 32F DAL-SIL includes adjustable legs for a desk with a single pedestal on the left side. Each leg has different screws. Model No. 32F DAL-SIR includes adjustable legs for a desk with a single pedestal on the right side. Each leg has different screws. • The adjustable legs illustrated below explain the (5) different types and their uses. Non-Pedestal Rear Leg for SIR Desks Front Pedestal Leg Rear Pedestal Leg Non-Pedestal Front Leg for SIR or SIL Desks Non-Pedestal Rear Leg for SIL Desks 3. Remove the (3) phillips screws and 5/16" hex screw that holds the end panel to the desk top. Remove the (3) 5/16" hex screws that hold the rear leg to the back panel.

Steelcase, Inc. Grand Rapids, MI 49501 U.S.A. 1-888-783-3522 Tools Assembly Directions Printed In U.S.A. REV 93-9500642 - Page 1 of 2 3/8” SOCKET 5/32” DRILL BIT Attaching An Extension Top To A 3200, 3300 or 4200 Series Desk EXTENSION TOP Assembly Directions 93-9500642 REV - Page 2 of 2 1. EXTENSION TOP Align braces with extension top using a square. Secure both braces to the extension top with No. 10 x 1/2 screws provided. 2. Align extension top with end of desk top. Mark and drill 5/32” holes in desk top edge. 3. Attach spacer plates to extension top by removing backing from tape (binding edge only). 4. Lift extension top just enough to remove the backing from the braces, align brace with the desk leg or end panel and press in place. 5. Tighten extension top attaching screws. PRE-DRILLED HOLES PRE-DRILLED HOLES BRACES NO. 10 X 1/2” SCREWS MARK AND DRILL 5/32” HOLES NO. 14 HEX HEAD SCREWS SPACER PLATES (Binding Edge Tops Only) REMOVE BACKING

Steelcase, Inc. Grand Rapids, MI 49501 U.S.A. 1-888-783-3522 Tools Assembly Directions Printed In U.S.A. REV 93-9500964 A Page 1 of 11 Installation Of A Lock System Into A Single Pedestal Desk Without A Center Drawer, Or On An executive High Wing-Unit With A Steel Top 1/8” DRILL BIT 3/32” DRILL BIT LOCK ROD LOCK ROD RETAINER SPRING CLIP SECURITY BRACKET TEMPLATE ANGLE LOCK GUARD (FOR 60” WIDE WING-UNITS ONLY) #8 SCREW INNER LOCK BAR ASSEMBLY LOCK ROD SCREW #8 x 3/8” LOCK ROD BRACKET #10 SCREW LOCK ROD COVER SUPPORT LOCK ROD COVER ANGLE LOCK ROD COVER #8 SCREW #10 FLAT HEAD SCREW SIMS SCREW ACTUATOR SPRING BEZEL LOCK CYLINDER� BRACKET SPRING RETAINER ACTUATOR LOCK ROD This installation direction covers package numbers shown in the chart below Assembly Directions 93-9500964 REV A Page 2 of 11 1. Box or personal drawer removal Pull drawer out until it stops. Press in on lock catch spring and at the same time pull out drawer. As drawer approaches the end of case channel, tip head of drawer down and lift out. LOCK CATCH (EACH SIDE OF DRAWER) DRAWER HEAD DRAWER RUNNER PACKAGE MODEL SERIES UNIT SIZE PACKAGE MODEL SERIES UNIT SIZE 5527531 3200 OR 4200 45” x 30” 5327535 3200 OR 4200 3200C62L 32A37L 4200C62L 42A37L 3200C47L 32A47L 4200C47L 42A47L 5517531 5200 45” x 30”S1 5327532 3200 OR 4200 55” x 30” 45” x 24”S1 70” x 30” 52A454-L 70” x 36” 5517532 5200 60” x 30”S1 65” x 30” 65” x 30”S1 60” x 30” 70” x 30”S1 60” x 36” 5517533 5200 52A374L 32A62L 52A604L 42A62L 5517534 5200 52C604L 5327534 3200 OR 4200 32B47L 52C754L 42B47L 5517535 5200 52B754L 32B62L 52B604L 42B62L 52B454L 32D62L 42D62L Assembly Directions 93-9500964 REV A Page 3 of 11 3. Removal of case channels from pedestal Remove the retaining case channels to the left side of each pedestal. Free and remove case channels by pulling out in direction of arrows. CASE CHANNELS PEDESTAL CASE CHANNELS SCREWS 2. File drawer removal When removing file drawers from pedestal, the cradle assembly must be removed with the drawer at the same time. Store drawer on the front face to prevent grease damage on carpet. To re-install, file drawer must be seated into cradle assembly then re-installed into pedestal. This is done to insure proper drawer alignment and ease operation. Installer should wipe any excess grease from exterior of cradle prior to re-assembly. BACK FLANGE CRADLE FILE DRAWER HEAD Assembly Directions 93-9500964 REV A Page 4 of 11 4. Installation of lock bar into pedestal Assemble inner lock bar tabs into slot located at the top and bottom of pedestal. Bend locking tab out in direction of arrows thus securing the lock bar in place. NOTE: A lock bar assembly is shown being installed into a left hand pedestal and is typical for a right hand all pedestals. 5. The lock tabs on lock bar must be at the same height as the lock catch located on side of drawers. Lock tabs may be pulled from one location and snapped into the proper location on lock bar for your drawer arrangement. DRAWER LOCK CATCH TAB SLOT LOCK BAR TAB TAB SLOT LOCKING TAB