Sturtevant Richmont exacta 2 Manuals

Sturtevant Richmont - P/N 857317 - Issue Date 161024 - Page 1 of 14 Sturtevant Richmont Accurate Reliable Durable: Tools You Trust 555 Kimberly Drive Carol Stream, IL 60881 Worldwide: +1-847/455-8677 US Toll Free 800/877-1347 Fax: 847/455-0347 [email protected] Operating and Service Manual 1200-Series Exacta® 2 Digital Torque Wrench www.srtorque.com NOTE: This tool requires the use of rechargeable NiMH AA batteries. Using ANY other type of battery immediately voids the 1-year limited warranty on this tool. The electronic circuit of the 1200 Series was designed to save power and operate on 1.2 volts. NiMH AA batteries are designed to provide ONLY 1.2 volts. AA Alkaline batteries provide 1.5 volts and therefore can damage the electronics. Tool Overview: SR 1200-Series Exacta® 2 Digital Torque Wrenches are designed to work with the Global 400 and Global 400mp process monitor/process monitors. These are the first digital torque wrenches with wireless capability that are designed for industrial assembly use. The wrench is completely dependent on the Global 400/400mp for directions and torque results reporting. Once connected to the Global 400/400mp, the wrench keypad is disabled. These tools are designed for ease of use. Operators simply pull to green, there are no buttons to push. The display and audible signal the operator of the status for each tightening. The display and Fresnel turn yellow when approaching minimum torque. The display turns green with an audible beep when target torque is achieved. Exceeding maximum torque causes the screen to turn red and the audible beep changes to one long tone. *Details on programming the tool through the Global 400/400mp process monitors are found in the process monitor manual and "how to" videos at www.srtorque.com. The 1200-Series Exacta 2 does not communicate with the Global 8. Safety: Always wear appropriate personal safety equipment when operating this tool. □ Never use this tool for any purpose other than that for which it is intended. □ Never use the tool beyond its’ rated torque capacity. □ Never immerse the tool in liquids. Battery and Battery Charger Selection The Exacta® 2 digital torque wrench has very specific battery requirements. • Use of any batteries not meeting SR NiMH AA rechargeable battery requirements could electronically and physically damage the tool and immediately void the warranty. • BATTERY CHARGING NOTE: The first time you charge NiMH batteries the batteries should remain charging for at least 24 hours. Removing the batteries from the charger prior to 24 hours shortens battery life and the number of cycles a battery can power in the wrench.

Sturtevant Richmont - Exacta® 2 - Page 1 of 20 Sturtevant Richmont The Tools You Trust . 555 Kimberly Drive Carol Stream, IL 60188 Phones Worldwide: +1 847/455-8677 Toll Free US Only: 800/877-1347 Fax: 847/455-0347 [email protected] www.srtorque.com Operating Instructions Exacta® 2 Digital Torque Wrenches Safety • Never use these tools for anything other than their designed purpose. • Never use these tools beyond their rated capacity. • Always wear and use appropriate safety equipment when operating these tools. Modes of Operation - General The Exacta® 2 digital torque wrenches have three modes of operation: Track, Peak and Residual. In the Track mode functions similarly to a dial or beam torque wrench. The current torque is shown on the display as it rises or falls in response to the force applied. This can be particularly useful when working with fasteners having a prevailing torque feature (crimping or insert) and for fastener testing. In the Peak mode, the torque is shown on the display as it rises, and when the force applied to the tool declines the maximum torque applied before the decline is retained on the screen for a period of time and stored in memory. This mode is exceptionally useful in assembly operations and some testing operations. This mode may be used with or without torque specifi cations having been programmed into the tool. The Residual mode is designed specifi cally to capture the torque remaining on a fastener after it has been installed and tightened. The theory behind this is that when testing the torque remaining on a fastener after installation, the torque applied to the fastener will rise until the fastener begins to move. When the fastener begins to move there will be a brief reduction in the torque followed by another rise in the torque. The bottom of this temporary reduction in applied torque is interpreted as the Residual torque. It must be noted that this works best on hard joints with stiff fasteners. For joints where this mode works well, the wrench makes an excellent auditing tool. S/R Dovetail and Interchangeable Heads Those models of the Exacta® 2 digital torque wrench that are equipped with an S/R dovetail are designed to be used with S/R interchangeable heads. The dovetail design provides an exceptionally strong and rigid connection.

Sturtevant Richmont - P/N 857282 Issued 100405 - Page 1 of 4 Sturtevant Richmont Global Reach. Local Support. 3203 N. Wolf Road, Franklin Park, IL 60131 Phones: 847/455-8677 800/877-1347 Fax: 847/455-0347 E-mail: [email protected] URL: www.srtorque.com Quick Start Instructions 1100-Series Exacta® 2 Digital Torque Wrench S/R 1100-Series Exacta® 2 Digital Torque Wrenches are designed to work with the Global 8, Global 8 - Ethernet, RFE and RFE - Ethernet controllers to provide torque application integration that extends from your shop control system all the way to the fastener. The details of programming the tool through each controller are found in the controller manual. Safety ◘ Always wear appropriate personal safety equipment when operating this tool. ◘ Never use this tool for any purpose other than that for which it is intended. ◘ Never use the tool beyond its’ rated torque capacity. Caution • When using this product with an S/R controller and radio communication is lost, the tool will retain the most recently-downloaded specifi cations until radio communication is re-established or alternate means are used to change the specifi cations. Battery and Battery Charger Selection The Exacta® 2 digital torque wrench has very specifi c battery requirements that must be adhered to. Only batteries meeting these requirements may be used. • Use of any batteries other than those provided by S/R or meeting the specifi cations on the Batteries page of our website (http://www.srtorque.com/batteries.html) may cause the tool to become inaccurate. • Use of any batteries other than those provided by S/R or meeting the specifi cations on the Batteries page of our website (http://www.srtorque.com/batteries.html) may damage the tool. • Use of any batteries other than those provided by S/R or meeting the specifi cations on the Batteries page of our website (http://www.srtorque.com/batteries.html) will void the warranty on the tool. • Under no circumstances should alkaline batteries, rechargeable or disposable, be used in the tool. The correct battery and charger pack (NAFTA countries only) for tools in the Exacta® 2 digital torque wrench line is S/R part number 21259. This pack includes a 15-minute charger and four (4) AA NiMH 2200 mAh batteries. The correct replacement battery pack (NAFTA countries only) for tools in the Exacta® 2 digital torque wrench line is S/R part number 21258. This pack includes four (4) AA NiMH 2500 mAh batteries.