Sunpak PF30X Manuals

Sunpak PF30X Flash Instructions Congratulations on your purchase of a Sunpak PF30X flash dedicated for use on the latest Canon, Nikon or Sony digital single lens reflex camera. Never use the flash on any camera brand other than the one noted on the base of the flash. Before use, please read the instructions carefully to take full advantage of its features and safe usage. Flash Safety * For maintenance, inspection or repair, return to ToCAD America Inc. * Never try to open, repair or modify the flash. Such action may result in fire, shock hazard or injury due to high voltage. * Never use accessories not specified by Sunpak. Using them may result in fire, shock hazard or injury. * If the flash is dropped or damaged, or impacted, return to ToCAD America Inc. for service and repair. * Never use the flash at close distances to subject’s eyes, especially babies and newborns. Using the flash at close distances to subject’s eyes may result in visual impairment. When shooting infants or newborns, keep the flash at a minimum distance of 3 feet or greater. * When loading batteries, install in the correct polarity. When replacing the batteries, replace both at the same time, use only the same model and type and from the same manufacturer. Incorrect battery usage may result in leakage, over heating, rupture, short battery time and loose contacts. * Never use the flash near glass or near containers holding cosmetics or chemicals. If cosmetics or chemicals enter the flash, it may result in fire, shock hazard or injury. * Never use the flash in a place with high humidity, such as in the bathroom or near a humidifier. It may result in fire, shock hazard or injury. * When cleaning or caring for the flash, be sure to remove the batteries. * Never use the flash in a place where flammable gas or explosive gas may exist in the air. * Keep batteries away from babies so that they will not be swallowed or ingested. * Never place the flash in a dusty environment, subject to direct sunlight or area of high humidity. Increased temperatures may result leading to serious damage, shock hazard or fire. * Never use the flash without the locking ring securely tightened. If left un-tightened it may fall or drop from the camera resulting in injury. Other Cautions * Never use benzene, thinner or alcohol to clean the flash. Use a soft cloth without chemicals or solvents. *If subject to moisture, remove the batteries and dry completely before reusing. *Neglecting any of these instructions may lead to injury or damage. Before use * Mount the flash on the camera and securely tighten the locking ring to secure to the camera. For operation, be sure to hold the body of the camera, not the flash. If the flash is used to hold the camera, the camera will break from the flash causing serious damage to the flash and camera. * For additional operating instructions and camera compatibility, go to www.sunpak.jp. Mounting When the PF30X is mounted or dismounted from the camera, be sure to turn OFF the Power switch. If the PF30X is mounted or dismounted with the power ON, malfunction or failure of the camera may result. 1. Insert the flash into the camera’s hot shoe firmly and turn the Locking Ring clockwise to secure the flash to the camera. For Sony version, turn the Locking Ring in the direction of the arrow until the ring locks into position. 2. After mounting the flash on the camera, turn on the camera and flash. 3. The shutter speed of the camera will automatically be set. 4. To confirm a correct exposure, the Auto Check function of the Test Charge indicator will flash approximately two seconds. If Auto Check function of the Test Charge indicator does not blink indicating a correct exposure, the distance from the flash to the subject is too great. Move closer to the subject if possible until confirmation of the Auto Check Test Charge indicator confirms the correct exposure. Installing Batteries 1. Confirm that the Power switch is OFF before loading the batteries. 2. Press down on the Battery cover and slide it downwards to open it. 3. Carefully load 2 AA type batteries into the battery box in accordance with the + - illustrations. The flash is designed to prevent incorrect loading, but if the batteries are installed incorrectly, failure will result. 4. Close the battery cover and slide it upward to close securely. Turn power switch to the ON position. Charging will start with the beep sound. During the charging cycle, the Ready Lamp will blink indicating the charging cycle and then to continues on for full charge status. (When fully charged, the lamp changes from blinking to steady lighting.) 5. To turn off, turn the Power switch to the OFF position. Before Mounting * When the flash is not mounted on a camera and turned on, use caution not to short-circuit the hot shoe terminals. If short-circuited, the flash may fire and cause an operational failure of the flash. * Nickel Metal-Hydride (NiMH) batteries are highly recommended to shorten the charging time and increase the number flashes. Information on the Ready Lamp Confirm after each shot that the Ready Lamp is on and not blinking. If blinking, charging is still taking place. If the flash is fired without the Ready Light on continuously, there will be insufficient flash to illuminate the subject causing an under exposure image. Therefore it is highly recommended for images with the optimum amount of illumination, wait until Ready Light remains on continuously. * If the Ready lamp continuously blinks for more than 30 seconds without changing to a continuous illumination, the voltage of the batteries has dropped below the recommend voltage and must be replaced. Flash Diffuser Battery Cover AF Assist Light Bounce Head + EV Indicator - EV Indicator - EV Selector + EV Selector Auto Check Ready Lamp/Test Power Switch Hot Shoe Locking Ring (Canon & Nikon ) Locking Ring (Sony) Hot Shoe (Sony)

OWNER'S MANUAL SONY ADI

Compatible with the latest digital SLR cameras from Canon with E-TTL II metering technology: • Digital Rebel, Rebel XT, Rebel XTi • EOS 40D • EOS 30D • EOS 20D • EOS 5D Compatible with the latest digital SLR cameras from Nikon with i-TTL metering technology: • D40, D40x, D50 • D70, 70s • D80 • D200 • Power 2-AA Alkaline, Ni-MH or Ni-Cd batteries • Number of flashes: approx. 100 at full manual (Alkaline batteries) • Auto effective range: 4.9 feet to 49 feet • AF assist effective range: 3.5 to 16 feet • Flash Control Mode: Canon E-TTL II, Nikon i-TTL • Flash speed: 1/800 second • EV adjustment: 7 steps (-1.5, -1, -0.5, 0, +0.5, +1, +1.5) • Dimensions: 4.1” high x 2.7" wide x 3.7" deep • Weight: 7 ounces (without batteries) • Guide number: 100, ISO 100/feet @ 35mm • Recycle time: approx. 10 seconds at full output (Alkaline) Product design and specifications subject to change without notice. Catalog Numbers PF30XC (Canon version) PF30XN (Nikon version) Sunpak PF30X Digital SLR Flash The Sunpak PF30X flash is the perfect accessory for today’s digital SLR cameras. For great con- trast and bright colors, the PF30X provides the power and flexibility that you need to make a great DSLR camera even better. With a five position bounce head images come out with a more pleasing light and illuminations without harsh shadows. Another great feature of the PF30X are the +/- EV adjustment buttons for greater control of the light output. Other features include a built-in AF assist light and a power sav- ing standby mode which automatically shuts down the flash after 5 minutes of inactivity. Highlights • Designed for today's digital SLR cameras with a hot shoe • Compatible with all camera exposure modes • Compact, lightweight digital design • Auto focus assist for low light shooting out to 16 feet • High guide number for greater range • Bounce flash head with 90 degree range • Bright, easy-to-read and use indicators and controls • Power saving standby mode • Auto shut off mode • Pro black finish Features Specifications ToCAD America Inc. 53 Green Pond Road Rockaway, NJ 07866, USA tocad.com