superbrightleds RGB-MDC83 Manuals

Begin the installation, by connecting an appropriate power supply to the controller. With the controller in standby mode (off) use the button to select each setting and buttons to adjust the setting values to match the table below. Once all setting adjustments have been made, and with supply power off, connect strip as shown using the provided adapter. Wiring Important: Read all instructions prior to installation. Dream-Color Chasing RGB Controller and Remote • Supports twelve unique IC strip styles and has pixel adjustment from 16 to 2,048 pixels to accommodate different strip lengths. • Input power should be 5–24 VDC (matching connected strip). Input power connection is a 5.5 mm / 2.1 mm DC barrel connector. • Ensure all electrical connections are secure and follow the provided wiring instructions. • Strips require data signal to operate properly. Use caution if cutting strip to custom length as interrupting the data signal will cause the strip(s) to malfunction. Strips should be powered from a single power supply connected to the controller, as additional power connections after the controller will cause the strip(s) to malfunction. • Jumper wires/interconnects should be no more than 8” between strip sections to avoid issues with data loss. Safety and Notes Specifications FCC Statement Controller Buttons Setup and Installation ¹Range may be decreased by interference from electrical signals and physical barriers ²This setting is for the full 5 m strip, part number NDC2-RGB150. Increase or decrease the pixel count by 1 for each additional 0.1 meter of strip. Model RGB-MDC83 Operating Temperature -4°–140° F (-20°–60° C ) Supply Voltage 5–24 VDC Maximum Output Power 5 A Maximum Remote Range¹ 175 ft (53.3 m) Terminal Connection Wire Color for NDC2-RGB150 V- strip negative black Data strip data green CLK strip clock blue V+ strip positive red Setting Value IC WS2811 LED Sequence RGB Pixels² 50 ON/OFF button turns the controller on or off. The controller must be off (powered on in standby mode) to adjust IC type, pixels, and LED sequence. Play/pause button can pause and then resume dynamic modes. Mode increase/decrease buttons cycle up or down to the next mode. They also adjust IC type, pixel number, and LED sequence in the settings. M+ and M- perform the same function on the remote control. Speed up/down buttons increase or decrease speed during dynamic modes. S+ and S- perform the same function on the remote control. Value selection buttons cycle through different setting types (IC type, pixel number, and LED sequence) in standby mode. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. WIFI-CON Important: Read all instructions prior to installation. RGB-MDC83 4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com Rev Date: V2 01/28/2020 User Manual V- V+ (Included LC4M-PT connector) D C Modes/Programs Available Settings Mode Program 1 Static Red 2 Static Blue 3 Static Green 4 Static Magenta 5 Static Yellow 6 Static Cyan 7 Static White 8 Red Chasing / Right 9 Red Chasing / Left 10 Blue Chasing / Right 11 Blue Chasing / Left 12 Green Chasing / Right 13 Green Chasing / Left 14 Red Chasing / Middle to Ends 15 Blue Chasing / Ends to Middle 16 RGB Chasing to Solid / Backward 17 CMY Chasing to Solid / Forward 18 RGB chasing to Solid / Middle to Ends 19 CMY Chasing to Solid / Ends to Middle 20 Seven Color Chasing to Solid / Backward 21 Seven Color Chasing to Solid / Forward 22 Seven Color Chasing to Solid (Backward) and Chasing (Forward) 23 Seven Color Chasing to Solid (Forward) and Chasing (Backward) 24 RGB Color Scan / Forward 25 RGB Scan / Backward 26 CMY Scan / Forward 27 CMY Scan / Backward 28 Seven Color Scan / Forward 29 Seven Color Scan / Backward 30 RGB Scan / Backward Then Flash Once 31 RGB Scan / Forward Then Flash Once 32 Seven Color Scan / Backward Then Flash Once 33 Seven Color Scan / Forward Then Flash Once 34 RGB Flash 35 Seven Color Flash 36 RGB Jump 37 CMY Jump 38 Seven Color Jump 39 GBM Flow / Forward 40 GCM Flow / Backward 41 CMY Flow / Forward 42 CMY Flow / Backward Mode Program 43 GYCM Flow / Forward 44 GB Alternating 45 GM Alternating 46 Seven Color Flow / Forward 47 Seven Color Flow / Backward 48 Green Comet / Backward 49 Red Comet / Forward 50 Red Comet / Backward 51 Blue Comet / Forward 52 Blue Comet / Backward 53 Green Comet / Forward 54 Magenta Comet / Forward 55 Cyan Comet / Forward 56 Yellow Comet / Backward 57 White Comet / Forward 58 White Comet / Backward 59 Seven Color Comet / Backward 60 Seven Color Comet / Forward 61 RC Gradual Change 62 YR Gradual Change Chasing / Backward 63 N/A 64 MB Gradual Change Chasing / Backward 65 N/A 66 BC Gradual Change Chasing / Backward 67 N/A 68 GY Gradual Change Chasing / Backward 69 N/A 70 CG Gradual Change Chasing/ Backward 71 N/A 72 WR Gradual Change Chasing/ Backward 73 N/A 74 RB Gradual Change 75 RG Gradual Change 76 MR Gradual Change Chasing/ Backward 77 N/A 78 RM Gradual Change 79 RY Gradual Change 80 BC Gradual Change 81 BM Gradual Change 82 GY Gradual Change 83 Scan Modes 1–82 Dream-Color Chasing RGB Controller and Remote WIFI-CON Important: Read all instructions prior to installation. RGB-MDC83 4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com Rev Date: V2 01/28/2020 User Manual This product is recommended for use with SBL strip part number NDC2-RGB150. If this is purchased to work with any other strip, the following settings are available. IC can be set to LPD6803, WS2801, P9813, and LPD8806 for data and clock operation, and TM1803, UCS1903, WS2811, TM1812, TM1809, TLS3011, TLS3008, and TM1829 for data operation. LED sequence can be set to RGB, RBG, GRB, GBR, BRG, or BGR. Pixel number can be set between 16 and 2,048.