Tableau TD2u Manuals

QUICK REFERENCE GUIDE GETTING STARTED TD2u TABLEAU FORENSIC DUPLICATOR 1 1 2 2 4 5 3 Power Press - On Hold - Off SATA Source IDE Source USB Source Alert Busy SATA Dest 1 SATA Dest 2 USB Dest 1 2 3 Setup Wizard: During the initial start-up or following a factory reset, the Setup Wizard will prompt you to configure the default system settings of the Duplicator. USB 2.0 Device Port (Optional) – Connect a USB storage device to save logs or a USB keyboard for easier data entry via the USB 2.0 port USB 2.0 Update Port – To update the firmware, connect the Duplicator to your computer via the mini USB port and use the Tableau Firmware Update utility. Confirm that the Duplicator is off before beginning. 1. Source Drive – Connect one drive to the Duplicator’s source side: SATA, IDE, USB 3.0, or SAS* * Tableau Duplicator SAS Expansion Module [TDP6] (sold separately) is needed for SAS drives. 2. Destination Drive(s) – Connect up to two SATA drives and one USB 3.0 drive to the Duplicator’s destination side 3. Duplicator Power – Connect the power supply to the Duplicator’s DC In 4. Power On – Press the power button and begin operation Before disconnecting a source or destination drive, we recommend powering down the Duplicator. 4 5 FIRMWARE UPDATES Guidance Software releases free firmware updates for Tableau products through the Tableau Firmware Update (TFU) utility. Reference the TFU webpage for more information: www.guid.com/tableau/tfu For support: Toll Free +1 (866) 973-6577 Main +1 (626) 229-9191 [email protected] For additional product information, visit: www.guid.com/tableau © Guidance Software, Inc. All rights reserved. Tableau is a registered trademark of Guidance Software, Inc. Updated 2/2017 USER GUIDE For a comprehensive overview of the Tableau TD2u features and functions, reference the Tableau TD2u User Guide: www.guid.com/tableau/td2u CABLE RECOMMENDATIONS Use a Tableau SATA/SAS Signal & Power cable [TC4-8-R2] Use a Tableau IDE Data cable [TC6-8] and Tableau IDE Power cable [TC2-8-R2] Use cable supplied with USB drive enclosure or directly connect Use a Tableau SATA/SAS Signal & Power cable [TC4-8-R2] Use a Tableau Power Supply [TP5] Use a Tableau USB cable [TC8] * Tableau Duplicator SAS Expansion Module [TDP6] (sold separately) is needed for SAS drives. For SATA Drive For IDE Drive For USB Drive For SAS Drive* For Power(DC In) For Firmware Updates

USER GUIDE Tableau TD2u Version 1.3 Copyright© 2018Guidance Software, Inc. Allrights reserved. EnCase®, EnScript®, FastBloc®, Guidance Software®and EnCE®are registered trademarks or trademarks owned by Guidance Software in the United States and other jurisdictions and may not be used without prior written permission. Allother marks and brands may be claimed as the property of their respective owners. Products and corporate names appearing in this work may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation into the owners' benefit, without intent to infringe. Any use and duplication of this work is subject to the terms of the license agreement between you and Guidance Software, Inc. Except as stated in the license agreement or as otherwise permitted under Sections 107or 108of the 1976United States Copyright Act, no part of this work may be reproduced, stored in a retrievalsystem or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, scanning, or otherwise. Product manuals and documentation are specific to the software versions for which they are written. For previous or outdated versions of this work, please contact Guidance Software, Inc. at https://www.guidancesoftware.com. Information contained in this work is furnished for informationaluse only, and is subject to change at any time without notice. January 05, 2018 CONTENTS Preface 7 About this Guide 7 Conventions Used in this Guide 7 Disk Capacity and Transfer Rate Measurement Con- ventions 7 CHAPTER 1 Overview 9 Tableau TD2u 11 TD2u Kit Contents 11 Navigating the TD2u 14 Reading the LEDs 15 USB Keyboard Support 15 CHAPTER 2 Setting up the TD2u 17 Startup Sequence 19 Initialization 19 Configuring the TD2u 19 User-Selected Startup Mode 19 System Settings (Menu 7.1) 20 Set Examiner Name (Menu 7.1.2) 21 Imaging Setup (Menu 7.2) 22 - iii -