TechNexion PICO-WIZARD-IMX8M Manuals

3.1 Connect the parts 3.3 Camera module / HDMI capture card (optional) PICO-WIZARD-IMX8M Quickstart Guide 3 Installation Instructions This installation guide will help you to assemble your development kit using step-by-step instructions to make sure all parts (development board, display, camera module and Wi-Fi antenna) are working. Connect the parts in the following order. Note that some versions of the PICO-WIZARD-IMX8M evaluation kit do not include the multi-touch display, camera/HDMI capture module and/or HDMI expander card. Tips: Do not power your board during the installation process. 3.2 Standoffs Let’s prepare four standoffs It only takes a few minutes. Step 1: Prepare evaluation board and standoffs. Step 2: Locate four standoffs holes on the evaluation board. Step 3: Locate a screw and insert it into the hole. Screw a standoff on the underside. Attach the standoffs for the remaining three holes. Please follow the steps below to properly install the camera module.The same steps can be applied to the installation of the HDMI capture card. Step 1: Prepare camera module, FPC cable and evaluation board. Step 2: Turn the camera module over to reveal a white connector near the edge of the module. Swivel the black retaining clip upward. Step 3: Insert either end of the camera module cable into the white connector. Make sure that the blue side of the ribbon is facing up and is aligned straight with the connector. The silver pins on the FPC cable should be facing down. Step 4: Swivel the retaining clip back down to hold the FPC cable in place. Steps 5 and 6: Repeat these same steps with the other end of the cable and the connector on the board. Tips: After installation remove the protective blue film from the camera lens. INNOVATORS OF TECHNOLOGY 2 Dimensions 1 Safety Precautions Thank you for purchasing a TechNexion PICO series evaluation kit based on NXP i.MX8M applications processor. This installation guide will be helpful in the installation, wiring and inspection of your TechNexion evaluation kit. Before using the product, please read this guide to ensure correct use. You should thoroughly understand all safety precautions before proceeding with the installation, wiring, and operation. Place this instruction sheet in a safe location for future reference. • Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet, allow it to dry completely. • Do not use or store the device in dusty or dirty areas. Its parts and electronic components can be damaged. • Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and warp or melt certain plastics. • Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form inside the device and damage electronic circuit boards. • This product is designed for specific applications and needs to be installed by qualified personnel. • Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and fine mechanics. • Do not paint the device. Paint can clog the parts and prevent proper operation. • Unauthorized modifications or attachments could damage the device and may violate regulations governing radio devices. • Do not touch any internal or exposed parts of the device as electrical shock may result. • Do not open the device while power is on. Otherwise electrical shock may result. • Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device. • Be sure the ventilation holes are not obstructed during operation. Otherwise malfunction may result due to bad ventilation or overheating. These suggestions apply equally to your device, battery, charger, or any enhancement. If any device is not working properly, take it to the nearest authorized service facility for service. • Make sure that the available power source matches the required input power of the device. Failure to observe this caution may result in electric shock or fire. 1.1 Storage and Installation 1.2 Wiring 1.3 Maintenance and Inspection ! Unit : mm 1 2 3 4 5 1 2 1 2 3 170 170 1.6 21.2 17.65 2.4 6.35 33.02 165.1 10.16 165.1 165.1 6.35 163.83 6