Telex TR-700 Manuals

Telex Op er ating In struc tions RadioCom™ BTR-700, TR-700 Pro fes sional Wire less In ter com Sys tem

Telex Op er ating In struc tions RadioCom™ BTR-700, TR-700 Pro fes sional Wire less In ter com Sys tem 0891 0885

MENU SET MIC PT TX PT TALK 6 7 8 9 MENU SET MIC PT TX PT TALK 2 1 3 4 5 TR-700 Quick Start Card Initial Beltpack and Base Station Set-up 1. Press [MENU] as powering-up the base station. This will place it on group 01A and set the receives on channels: 01, 02 , 03 and 04. Ensure the appropriate portable station connect path is enabled. If used stand alone, the base should be in the 4-wire mode. 2. Set beltpack back panel slide switch to push-to-talk (PT TALK). 3. Press [MENU] as powering-up the beltpack. This will place the beltpack on group 01A with channel 01 flashing. 4. Use the [UP] and [DOWN] arrow buttons to change the channel to an unoccupied receive channel on the base station. Then press [SET]. Press [MENU] if not changing channels. 5. The group/channel on the beltpack should now match the group and a receive channel on the base station. Nothing should be flashing on the beltpack screen. 6. Plug a headset into the beltpack and set the microphone gain so the BAT/OM light flashes at the beginning of most words at normal speech levels. Special Functions ClearScan· · · · · · · Press [MENU]+[SET] buttons for 3 seconds. After 25 seconds of searching, the beltpack will produce a list of the groups organized from best (clearest) to worse. The best group is displayed flashing. Use the [UP] and [DOWN] buttons to select other groups if desired. Lockout · · · · · · · · Press [UP]+[DOWN] arrows buttons for 3 seconds. Repeat to toggle it off/on. 1st Use Default · · · Press [MENU] as powering-up the beltpack. Sets beltpack on group 01A with channel 01 flashing. User must then set the channel. All user-programmed memory is retained. Factory Default · · Press [MENU]+[SET]+[UP]+[DOWN] buttons for 3 seconds to software “reset” the beltpack. All user-programmed memory is erased. Talk Latch Enable/Disable Talk Button . . . . . . . . . . . . . . . . Press and hold [SET] then press [TALK] to enable latching or non-latching. 1. [MENU] and [SET] buttons – Used to select menus and set options on the LCD. 2. LCD display. 3. [UP] and [DOWN] buttons – Used to select beltpack options on the LCD. 4. Microphone Gain – Adjusts the headset’s microphone gain. Adjust so that the light flashes at the beginning of most words at normal speech levels. 5. Push-to-Talk/Push-to-Transmit Switch – Push-to-Talk (PT TALK) – The transmitter is always on. No audio sent unless the talk button is pressed. Recommended position. Push-to-Transmit (PT TX) - The transmitter and audio path are off except when the talk button is pressed. 6. Headset Connector – Male XLR connector for Telex units, Female XLR connector for RTS units. 7. Battery Latch – Press down to enable the battery pack to be released. While the latch is held down, slide the battery pack about 1/8 inch back, toward the latch, until it stops, then lift out. 8. Receive Antenna – Screw type ¼ wave replaceable antenna. The receiver antenna is always the longer antenna. Color dot on the screw end of the antenna must match color dot on antenna receptacle. 9. Transmit Antenna – Screw type ¼ wave replaceable antenna. Color dot on the screw end of the antenna must match color dot on antenna receptacle. MENU SET MIC PT TX PT TALK 6 7 8 9 MENU SET MIC PT TX PT TALK 2 1 3 4 5 TR-700 Quick Start Card Initial Beltpack and Base Station Set-up 1. Press [MENU] as powering-up the base station. This will place it on group 01A and set the receives on channels: 01, 02 , 03 and 04. Ensure the appropriate portable station connect path is enabled. If used stand alone, the base should be in the 4-wire mode. 2. Set beltpack back panel slide switch to push-to-talk (PT TALK). 3. Press [MENU] as powering-up the beltpack. This will place the beltpack on group 01A with channel 01 flashing. 4. Use the [UP] and [DOWN] arrow buttons to change the channel to an unoccupied receive channel on the base station. Then press [SET]. Press [MENU] if not changing channels. 5. The group/channel on the beltpack should now match the group and a receive channel on the base station. Nothing should be flashing on the beltpack screen. 6. Plug a headset into the beltpack and set the microphone gain so the BAT/OM light flashes at the beginning of most words at normal speech levels. Special Functions ClearScan· · · · · · · Press [MENU]+[SET] buttons for 3 seconds. After 25 seconds of searching, the beltpack will produce a list of the groups organized from best (clearest) to worse. The best group is displayed flashing. Use the [UP] and [DOWN] buttons to select other groups if desired. Lockout · · · · · · · · Press [UP]+[DOWN] arrows buttons for 3 seconds. Repeat to toggle it off/on. 1st Use Default · · · Press [MENU] as powering-up the beltpack. Sets beltpack on group 01A with channel 01 flashing. User must then set the channel. All user-programmed memory is retained. Factory Default · · Press [MENU]+[SET]+[UP]+[DOWN] buttons for 3 seconds to software “reset” the beltpack. All user-programmed memory is erased. Talk Latch Enable/Disable Talk Button . . . . . . . . . . . . . . . . Press and hold [SET] then press [TALK] to enable latching or non-latching. 1. [MENU] and [SET] buttons – Used to select menus and set options on the LCD. 2. LCD display. 3. [UP] and [DOWN] buttons – Used to select beltpack options on the LCD. 4. Microphone Gain – Adjusts the headset’s microphone gain. Adjust so that the light flashes at the beginning of most words at normal speech levels. 5. Push-to-Talk/Push-to-Transmit Switch – Push-to-Talk (PT TALK) – The transmitter is always on. No audio sent unless the talk button is pressed. Recommended position. Push-to-Transmit (PT TX) - The transmitter and audio path are off except when the talk button is pressed. 6. Headset Connector – Male XLR connector for Telex units, Female XLR connector for RTS units. 7. Battery Latch – Press down to enable the battery pack to be released. While the latch is held down, slide the battery pack about 1/8 inch back, toward the latch, until it stops, then lift out. 8. Receive Antenna – Screw type ¼ wave replaceable antenna. The receiver antenna is always the longer antenna. Color dot on the screw end of the antenna must match color dot on antenna receptacle. 9. Transmit Antenna – Screw type ¼ wave replaceable antenna. Color dot on the screw end of the antenna must match color dot on antenna receptacle.