Theben TR 652 S Manuals

english Digital Timers TR 651 S 1-channel timer No. 651 0 001 TR 652 S 2-channel timer No. 652 0 001 TR 653 S 3-channel timer No. 653 0 001 310 051 01 1.0 Information The devices TR 651 S – TR 653 S comes ready programmed with the current time and with the relevant Greenwich mean time rule for automatic sum- mer / winter timer adjustment. Should you require a different time adjustment rule, or none at all, the new rule can be selected from the table (chapter 18.2) and re-programmed as described in chapter 18.3 to 18.6. 2.0 Application Time switches switch on, off or over, electrical units time dependent on a day or week cycle.Time switch TR 651 S,TR 652 S,TR 653 S, is suitable in dry spaces and for assembly to the 35 mm top-hait rail (DIN EN 50022). If assembly kit 907 0 050 is used, the installation can be fitted to a wall. 3.0 Safety information Electrical devices should only be connected and mounted by an electrical specialist. The national specifications and applicable safety regulations must be observed. Manipulations and modifications on the switch will be result in loss of warranty. Despite elaborate safety precautions, exceptionally strong electrical fields may cause interference with the microprocessor-controlled time switch.We therefore recom- mend that you observe the following points before installation: • Suppress interference of inductive loads by means of an RC filter • Use a separate line for the mains voltage suppply • Do not install device in close proximity to sources of interference, e.g. transfor- mers, contactors, PCs and TV sets. • If interference occurs, we recommed that you carry out a RESET before putting the device back into operation (press button v + C1 simultaneously). Attention This action deletes all stored switching times! 4.0 Features – free block formation of the weekdays – 140 memory locations – holiday program, programmable 21 days in advance for max. 45 days – Pulse program, 1 – 59 sec., switching times programmable precise to the second. – 1 x switching e.g. for one time program override on holidays 5.0 Electrical connection TR 651 S TR 652 S TR 653 S 6.0 Technical Data Operating voltage: 240 V~ + 6 % / – 14 % 230 V~ ± 10 % Mains frequence: TR 651 S/652 S 50 – 60 Hz TR 653 S 50 Hz Specified voltage range: TR 653 S 60 Hz Own consumption: aprox. 7 VA (TR 653 approx. 14 VA) Contact rating: TR 651 / 652 S 16 A, 250 V~, cos ϕ = 1 10 A, 250 V~, cos ϕ = 0,6 TR 653 S 10 A, 250 V~, cos ϕ = 1 6 A, 250 V~, cos ϕ = 0,6 (Kontakte, potentialfreii) Kontaktmaterial: AgSnO Time base: quartz Memory locations: 140 Shortest possible switching interval: 1 minute Impuls einstellbar: 1 – 59 Sek. Switching accuracy: precise-to-the second Running accuracy: ≤±1 sec. / deg at 20 °C Power reserve: Lithium max. 8 years at 20 °C Admissible ambient temperature: –10 °C ... +50 °C (-10T50) Class of protection: II acc. to EN 60 335-1 when mounted Type of enclosure: IP 20 acc. to EN 60 529 Type: 1 BSTU acc. EN 60730-2-7 Interference suppression degree: The time switches are in accordance with the European directives 73/23/EWG Low- Voltage Directive) and 89/336/EWG (EMC-Directive). If the time switches are used together with other devices in an installation, take care that the complete installation does not cause a radio interference. Dimentioned drawing 7.0 Automatic reset If no buttons are pressed for a certain length of time in the checking or program- ming mode, the display is automatically reset to automatic mode after approx. 40 sec.The device then assumes the switching status dictated by the program. 8.0 Setting / changing the current time Should the time already set in the factory vary slightly, it can be corrected as follows: Press button vfor approx 1 sec. (see Cursor under ). Change the controll-time with button h or m. Store it by pressing the button ENTER. 9.0 Programming e. g. switch C1 Mo – Fr 8.00 (On) press button v see Note: Using the 1 channel timer TR 651 S Cursor in Pos. the key C is pressed instead of C1 or C2. C1 (On) > Enter > d > Enter > d > Enter > d > Enter > d > Enter > h ... (8 h) > Enter. e. g. switch C1 Mo – Fr 18.00 (OFF) C1 > C1 (OFF) > Enter > d > Enter > d > Enter > d > Enter > d > Enter > h ... (18 h) > Enter. Pressing the keys h or m for more than 2 seconds, a fast run – through is carried out. 10. One-time switching e. g. one time wednesday 9.45 switch C1 on. One-time switch has priority Enter (1x) > C1 (On) > d ... (3 = We) > Enter > h ... (9 h) > m > (45 min.) > Enter. 11. Program switching e. g. Channel C2 thursday 7:15 switching-on times Impuls 10 sec. C2 (On) > 2 x d > Enter > h (7 h) > m (15 min.) > Enter > m > (10 sec.) > Enter. Attention: If you want to program only the switching times of the pulse program, you must program additional the daily OFF switching times. 12. Pulse program Switching times can be prolonged by 1 – 59 sec. with an additional On rubbe command. C1 (On) > 1 x d (Tue) > Enter > h (7 h) > Enter C1 > C1 (OFF) > 1 x d (Tue) > Enter > h (7 h) > Enter > m (25 sec.) > Enter. N L N 1 2 3 L M N L N 1 2 3 4 5 6 L C 1 C 2 M N L N 1 2 3 4 5 6 7 8 L C 1 C 2 C 3 M program display switch position of the channels On, OFF H = holiday program 1 x = one-time switch setting of minutes selection of channel and ON / OFF program entry / recall time / response time day indication e. g. 1 = Monday 2 = Tuesday setting of weekday setting of hours program selector switch or C ~ ~