Therma-Stor Phoenix D385 Manuals

1 www.usephoenix.com • [email protected] Toll-Free 1-800-533-7533 Owner’s Manual — Phoenix D385 Installation, Operation & Service Instructions Read and Save These Instructions The Phoenix D385 provides the perfect combination of features and performance the restoration industry has been craving in a desiccant dehumidifier. Designed to operate vertically or horizontally, the Phoenix D385 provides the wide operating range and ultra-low grains of a desiccant with the water removal capacity of the largest LGR’s in cabinet dimensions identical to our popular Phoenix 200 Max. The D385 delivers 385 CFM of ultra-low grain process air and removes an incredible 116 pints per day at AHAM conditions. The true four hole configuration* allows the Phoenix D385 to be located in the affected area with the 75 CFM re-activation air stream isolated from the drying chamber. Three hole designed units** inherently pull unaffected and/or outside air into the drying chamber. The D385’s four hole design allows the restoration contractor to set-up for effective positive, neutral or negative pressure operation. Able to operate vertically or horizontally, the D385 will fit inside most crawlspaces. Having the D385 securely inside, rather than outside the crawlspace access, deters the possibility of tampering with the dehumidifier or the set- up. The 385 CFM of process air will provide 3 ACH on an affected area up to 7000 cubic feet. The Phoenix D385 is easy to transport and set-up. The D385 will fit on your truck in the areas already designed for your LGR’s and will move around the jobsite with the same portability. All the power to the unit is provided by two 115 volt grounded power cords. Simply plug the cords into separate 15 amp circuits. Each cord draws only 11 amps to power the D385. The re-activation air stream is ducted through 6” flex duct provided with the unit and stores conveniently in the top of the unit. *Having completely separate process and regeneration airstreams. **Where regeneration airstream is pulled from the process airstream. The Phoenix D385 Desiccant Dehumidifier • Ultra low grains • Wide operating range • 116 pints per day @ AHAM • Operates vertically or horizontally • Process airflow 385 CFM • Two 23’ power cords: 11 Amps per cord 22 Amps 115 Volts/60 Hz • Unlimited ducting possibilities • Legendary stainless construction Phoenix D385 PN 4026700 Specifications subject to change without notice. TS-387 Revised 7/07 PO Box 8680 • Madison, WI 53708  www.usephoenix.com • [email protected] Toll-Free 1-800-533-7533 1 Specifications Part No. 4026700 Power 2 circuits: 11 Amps, 115 VAC each 22 Amps total power consumption Water 116 pints per day AHAM Removal Blower 385 CFM Process Airflow 75 CFM Reactivation Airflow Operating Up to 140°F Range As low as 10°F Filters Process filter size: 16” x 20” x 2” Reactivation filter size: 12” x 12” x 1” Duct Process Inlet: 12” Flex-Duct (optional) Connections Process Outlet: 10” Lay Flat collar (optional) Reactivation Inlet: 6” Flex-Duct (optional) Reactivation Outlet: 6” Flex-Duct (required) Warranty One year Parts and Labor Dimensions: Machine Shipping Width 24-1/4” 27-1/2” Height 40” 45-1/2” Depth 21-3/8” 22” Weight 105 Lbs. 130 Lbs. Popular Accessories 4026859 6” Metalized Polyester Flex-Duct 25’ (Standard) 4020128 6” Insulated Flex-Duct 25’ 4024750 12” Metalized Polyester Flex Duct 25’ 4022537 10” Lay Flat Duct 500’ 4024935 10” Lay Flat Duct 250’ 4024440 Kestrel 3000 Multi-Function Air Meter Process Air Filter Replacement 4021475 16” x 20” x 2” MERV 11 Filter (Standard) 4024969 16” x 20” x 2” MERV 6 Filter (Optional) 4022164 16” x 20” x 2” MERV 14 Filter (Optional) Reactivation Air Filter Replacement 4026315 12” x 12” x 1” MERV 7 Filter (Standard) Read the operation and maintenance instructions carefully before using this unit. Proper adherence to these instructions is essential to obtain maximum benefit from your Phoenix D385 dehumidifier. Table of Contents Introduction.................................................................1 1. Specifications.........................................................2 2. Operation..............................................................3 2.1 How The Phoenix D385 Works...........................3 2.2 Avoiding Secondary Damages............................3 2.3 Universal Use Set-Up........................................3 2.4 Location..........................................................4 2.5 Electrical Requirements....................................4 2.6 Control Panel...................................................4 2.6A Power Switch.............................................4 2.6B Pilot Light.................................................4 2.6C Hour Meter...............................................4 2.7 Ducting Connections........................................4 2.8 Storage and Transportation...............................5 3. Maintenance..........................................................5 3.1 Air Filter Replacement......................................5 4. Service..................................................................5 4.1 Warranty..........................................................5 5. Wiring Diagram......................................................5 6. Service Parts List...................................................6 7. Warranty................................................................7 Serial No. ___________________________ Purchase Date ______/______/_____ Dealer’s Name ___________________________________  www.usephoenix.com • [email protected] Toll-Free 1-800-533-7533 2 Operation 2.1 How the Phoenix D385 works Your Phoenix D385 has two separate air streams that run through it – Process (Fig. 1) and Reactivation (Fig. 2). Process Air Stream: P1 – 385 CFM of air enters (12”flex) the top of the machine and... P2 – ...water vapor from incoming air is deposited on the desiccant wheel. P3 – 385 CFM of dry air exits (10” lay flat) the machine. Reactivation Air Stream: R1 – 75 CFM of air enters (6”flex) the lower-side of the machine and... R2 – passes over the heater coils. R3 – Water vapor is picked up from the desiccant wheel by the hot air and... R4 – ...75 CFM of wet air exits (6”flex) the machine. 2.2 Avoiding Secondary Damages The D385 is a powerful tool capable of removing a great deal of water from most environments. Care must be taken to avoid secondary damages of over-drying and or unexpected condensation. Your Phoenix D385 removes vapor water from the incoming process air stream (Fig. 1) and transfers it to the outgoing reactivation air stream (Fig. 2). The reactivation exhaust air is hot and wet. Take care to prevent the reactivation exhaust air stream from causing secondary damage due to condensation. If the reactivation exhaust air stream cools below its dewpoint liquid water will condense inside the duct work creating puddles. If the reactivation exhaust air stream is not exhausted completely from the structure it can also cause secondary water damage. Your Phoenix D385 does not produce liquid water internal to the machine. There is no condensate pump and no drain hose. The D385 desiccant dehumidifier will continue to remove water from already dry, cold air. It is possible to over-dry objects and or structures. Care must be taken to avoid secondary damages due to over-drying. 2.3 Universal Use Set-Up When conditions warrant the use of a desiccant dehumidifier, use the set-up shown below (Fig. 3). This universal set-up will produce efficient drying, while avoiding secondary damages. The Phoenix D385 has been designed with the goal of being easy to use every time. Therma-Stor LLC | Madison, WI | 800-533-7533 PORTABLE DESICCANT DEHUMIDIFIER PORTABLE DESICCANT DEHUMIDIFIER Optional 12” Flex-Duct Optional 10” Lay Flat Duct 385 CFM 385 CFM Therma-Stor LLC | Madison, WI | 800-533-7533 PORTABLE DESICCANT DEHUMIDIFIER PORTABLE DESICCANT DEHUMIDIFIER Hot Wet Air Room or Outdoor Ambient Air Duct Outside! 75 CFM 75 CFM Optional 6” Flex Duct Required 6” Flex Duct Figure 1: Desiccant process air stream. Figure 2: Desiccant reactivation air stream. P1 P2 P3 R4 R1 R3 R2 Figure 3: Universal D385 Set-up Therma-Stor LLC | Madison, WI | 800-533-7533 PORTABLE DESICCANT DEHUMIDIFIER PORTABLE DESICCANT DEHUMIDIFIER 6” Flex-Duct 75 CFM 75 CFM

1 www.usephoenix.com • [email protected] Toll-Free 1-800-533-7533 Owner’s Manual — Phoenix D385 Installation, Operation & Service Instructions Read and Save These Instructions The Phoenix D385 provides the perfect combination of features and performance the restoration industry has been craving in a desiccant dehumidifier. Designed to operate vertically or horizontally, the Phoenix D385 provides the wide operating range and ultra-low grains of a desiccant with the water removal capacity of the largest LGR’s in cabinet dimensions identical to our popular Phoenix 200 Max. The D385 delivers 385 CFM of ultra-low grain process air and removes an incredible 116 pints per day at AHAM conditions. The true four hole configuration* allows the Phoenix D385 to be located in the affected area with the 75 CFM re-activation air stream isolated from the drying chamber. Three hole designed units** inherently pull unaffected and/or outside air into the drying chamber. The D385’s four hole design allows the restoration contractor to set-up for effective positive, neutral or negative pressure operation. Able to operate vertically or horizontally, the D385 will fit inside most crawlspaces. Having the D385 securely inside, rather than outside the crawlspace access, deters the possibility of tampering with the dehumidifier or the set- up. The 385 CFM of process air will provide 3 ACH on an affected area up to 7000 cubic feet. The Phoenix D385 is easy to transport and set-up. The D385 will fit on your truck in the areas already designed for your LGR’s and will move around the jobsite with the same portability. All the power to the unit is provided by two 115 volt grounded power cords. Simply plug the cords into separate 15 amp circuits. Each cord draws only 11 amps to power the D385. The re-activation air stream is ducted through 6” flex duct provided with the unit and stores conveniently in the top of the unit. *Having completely separate process and regeneration airstreams. **Where regeneration airstream is pulled from the process airstream. The Phoenix D385 Desiccant Dehumidifier • Ultra low grains • Wide operating range • 116 pints per day @ AHAM • Operates vertically or horizontally • Process airflow 385 CFM • Two 23’ power cords: 11 Amps per cord 22 Amps 115 Volts/60 Hz • Unlimited ducting possibilities • Legendary stainless construction Phoenix D385 PN 4026700 Specifications subject to change without notice. TS-387 Revised 1/08 PO Box 8680 • Madison, WI 53708 2 www.usephoenix.com • [email protected] Toll-Free 1-800-533-7533 1 Specifications Part No. 4026700 Power 2 circuits: 11 Amps, 115 VAC each 22 Amps total power consumption Water 116 pints per day AHAM Removal Blower 385 CFM Process Airflow 75 CFM Reactivation Airflow Operating Up to 140°F Range As low as 10°F Filters Process filter size: 16” x 20” x 2” Reactivation filter size: 12” x 12” x 1” Duct Process Inlet: 12” Flex-Duct (optional) Connections Process Outlet: 10” Lay Flat collar (optional) Reactivation Inlet: 6” Flex-Duct (optional) Reactivation Outlet: 6” Flex-Duct (required) Warranty One year Parts and Labor Dimensions: Machine Shipping Width 24-1/4” 27-1/2” Height 40” 45-1/2” Depth 21-3/8” 22” Weight 105 Lbs. 130 Lbs. Popular Accessories 4026859 6” Metalized Polyester Flex-Duct 25’ (Standard) 4020128 6” Insulated Flex-Duct 25’ 4024750 12” Metalized Polyester Flex Duct 25’ 4022537 10” Lay Flat Duct 500’ 4024935 10” Lay Flat Duct 250’ 4024440 Kestrel 3000 Multi-Function Air Meter Process Air Filter Replacement 4021475 16” x 20” x 2” MERV 11 Filter (Standard) 4024969 16” x 20” x 2” MERV 6 Filter (Optional) 4022164 16” x 20” x 2” MERV 14 Filter (Optional) Reactivation Air Filter Replacement 4026315 12” x 12” x 1” MERV 7 Filter (Standard) Read the operation and maintenance instructions carefully before using this unit. Proper adherence to these instructions is essential to obtain maximum benefit from your Phoenix D385 dehumidifier. Table of Contents Introduction.................................................................1 1. Specifications.........................................................2 2. Operation..............................................................3 2.1 How The Phoenix D385 Works...........................3 2.2 Avoiding Secondary Damages............................3 2.3 Universal Use Set-Up........................................3 2.4 Location..........................................................4 2.5 Electrical Requirements....................................4 2.6 Control Panel...................................................4 2.6A Power Switch.............................................4 2.6B Pilot Light.................................................4 2.6C Hour Meter...............................................4 2.7 Ducting Connections........................................4 2.8 Storage and Transportation...............................5 3. Maintenance..........................................................5 3.1 Air Filter Replacement......................................5 4. Service..................................................................5 4.1 Warranty..........................................................5 5. Wiring Diagram......................................................5 6. Service Parts List...................................................6 7. Warranty................................................................7 Serial No. ___________________________ Purchase Date ______/______/_____ Dealer’s Name ___________________________________ 3 www.usephoenix.com • [email protected] Toll-Free 1-800-533-7533 2 Operation 2.1 How the Phoenix D385 works Your Phoenix D385 has two separate air streams that run through it – Process (Fig. 1) and Reactivation (Fig. 2). Note: Check for airflow at all inlets and outlets. DO NOT run unit if no airflow is detected. Process Air Stream: P1 – 385 CFM of air enters (12”flex) the top of the machine and... P2 – ...water vapor from incoming air is deposited on the desiccant wheel. P3 – 385 CFM of dry air exits (10” lay flat) the machine. Reactivation Air Stream: R1 – 75 CFM of air enters (6”flex) the lower-side of the machine and... R2 – passes over the heater coils. R3 – Water vapor is picked up from the desiccant wheel by the hot air and... R4 – ...75 CFM of wet air exits (6”flex) the machine. 2.2 Avoiding Secondary Damages The D385 is a powerful tool capable of removing a great deal of water from most environments. Care must be taken to avoid secondary damages of over-drying and or unexpected condensation. Your Phoenix D385 removes vapor water from the incoming process air stream (Fig. 1) and transfers it to the outgoing reactivation air stream (Fig. 2). The reactivation exhaust air is hot and wet. Take care to prevent the reactivation exhaust air stream from causing secondary damage due to condensation. If the reactivation exhaust air stream cools below its dewpoint liquid water will condense inside the duct work creating puddles. If the reactivation exhaust air stream is not exhausted completely from the structure it can also cause secondary water damage. Your Phoenix D385 does not produce liquid water internal to the machine. There is no condensate pump and no drain hose. The D385 desiccant dehumidifier will continue to remove water from already dry, cold air. It is possible to over-dry objects and or structures. Care must be taken to avoid secondary damages due to over-drying. 2.3 Universal Use Set-Up When conditions warrant the use of a desiccant dehumidifier, use the set-up shown below (Fig. 3). This universal set-up will produce efficient drying, while avoiding secondary damages. The Phoenix D385 has been designed with the goal of being easy to use every time. Optional 12” Flex-Duct Optional 10” Lay Flat Duct 385 CFM 385 CFM Therma-Stor LLC | Madison, WI | 800-533-7533 PORTABLE DESICCANT DEHUMIDIFIER PORTABLE DESICCANT DEHUMIDIFIER Hot Wet Air Room or Outdoor Ambient Air Duct Outside! 75 CFM 75 CFM Optional 6” Flex Duct Required 6” Flex Duct Figure 1: Desiccant process air stream. Figure 2: Desiccant reactivation air stream. P1 P2 P3 R4 R1 R3 R2 Figure 3: Universal D385 Set-up PORTABLE DESICCANT DEHUMIDIFIER PORTABLE DESICCANT DEHUMIDIFIER 6” Flex-Duct 75 CFM 75 CFM