Thermador VTR1000Q Manuals

IMPORTANT: Save these instructions for the Local Electrical Inspector’s use. INSTALLER: Please leave these Instructions with this unit for the owner. OWNER: Please retain these instructions for future reference. INSTALLATION INSTRUCTIONS for ISLAND HOOD ® FOR RESIDENTIAL USE ONLY

1 Dim. Model A B C VTR600R 5-11/16" 6-1/8" 9" VTR1000Q 7-1/4" 6-15/16" 11" VTR1400Q 7-1/4" 6-15/16" 11" INSTALLATION INSTRUCTIONS ROOF OR WALL VENTILATOR MODEL VTR1400Q, VTR1000Q & VTR600R IMPORTANT SAFETY INSTRUCTIONS WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PER- SONS, OBSERVE THE FOL- LOWING: A. Installation work and electrical wir- ing must be done by qualified person(s) in accordance with all applicable codes & standards, in- cluding fire-rated construction. B. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equip- ment manufacturers guideline and safety standards such as those pub- lished by the National Fire Protec- tion Association (NFPA), and the American Society for Heating, Re- frigeration and Air Conditioning En- gineers (ASHRAE), and the local code authorities. C. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. D. To properly exhaust air, be sure to duct air out side. Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces, or ga- rages. WARNING: To reduce the risk of fire, use only metal ductwork. CAUTION - For General Ventilat- ing Use Only. Do Not Use To Exhaust Hazardous Or Explosive Materials And Vapors. Fig. 1 TOP VIEW Down Slope of Roof or Wall I. INSTALLATION: 1. Remove and discard shipping bracket (attached to mo- tor mounts and inlet collar). Check to see if blower wheel turns freely. Do not replace top until installation is complete. 2. Provide a square cutout through the roof (or wall) as shown by the dashed lines, or cut a round hole to fit duct with a separate hole for electrical conduit as shown by solid lines in Fig. 1. 3. Install the remote ventilator with the discharge pointing down slope as shown in Figures 3 and 4. Follow standard roofing procedures. Install the ventilator so the dis- charge edge is on top of the shingles and the rear edge is underneath the shingles. B 14" 1" C Dia. A 1" 1-1/4 " Hole 14" PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING. IMPORTANT: Save these instructions for the Local Electrical Inspector’s use. INSTALLER: Please leave these Installation Instructions with this unit for the owner. OWNER: Please retain these instructions for future reference. Recommended for use only over conventional domestic gas and electric ranges, and use with an approved Thermador Hood. READ AND SAVE THESE INSTRUCTIONS SAFETY WARNING: Before ser- vicing or cleaning unit, switch power off at the service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, attach a tag to the service panel to indicate power has been switched off for maintenance.

1 Dim. Model A B C VTR600R 5-11/16" 6-1/8" 9" VTR1000Q 7-1/4" 6-15/16" 11" VTR1400Q 7-1/4" 6-15/16" 11" INSTALLATION INSTRUCTIONS ROOF OR WALL VENTILATOR MODEL VTR1400Q, VTR1000Q & VTR600R IMPORTANT SAFETY INSTRUCTIONS WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PER- SONS, OBSERVE THE FOL- LOWING: A. Installation work and electrical wir- ing must be done by qualified person(s) in accordance with all applicable codes & standards, in- cluding fire-rated construction. B. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equip- ment manufacturers guideline and safety standards such as those pub- lished by the National Fire Protec- tion Association (NFPA), and the American Society for Heating, Re- frigeration and Air Conditioning En- gineers (ASHRAE), and the local code authorities. C. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. D. To properly exhaust air, be sure to duct air out side. Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces, or ga- rages. WARNING: To reduce the risk of fire, use only metal ductwork. CAUTION - For General Ventilat- ing Use Only. Do Not Use To Exhaust Hazardous Or Explosive Materials And Vapors. Fig. 1 TOP VIEW Down Slope of Roof or Wall I. INSTALLATION: 1. Remove and discard shipping bracket (attached to mo- tor mounts and inlet collar). Check to see if blower wheel turns freely. Do not replace top until installation is complete. 2. Provide a square cutout through the roof (or wall) as shown by the dashed lines, or cut a round hole to fit duct with a separate hole for electrical conduit as shown by solid lines in Fig. 1. 3. Install the remote ventilator with the discharge pointing down slope as shown in Figures 3 and 4. Follow standard roofing procedures. Install the ventilator so the dis- charge edge is on top of the shingles and the rear edge is underneath the shingles. PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING. IMPORTANT: Save these instructions for the Local Electrical Inspector’s use. INSTALLER: Please leave these Installation Instructions with this unit for the owner. OWNER: Please retain these instructions for future reference. Recommended for use only over conventional domestic gas and electric ranges, and use with an approved Thermador Hood. READ AND SAVE THESE INSTRUCTIONS SAFETY WARNING: Before servic- ing or cleaning unit, switch power off at the service panel and lock service disconnecting means to prevent power from being switched on acci- dentally. When the service discon- necting means cannot be locked, at- tach a tag to the service panel to indicate power has been switched off for maintenance.