Thermo King T- series Manuals

Simple to Start: One or Multiple Zones 1. Press the ON key to turn the unit on. • Dashes will appear in both the upper and lower portions of the display as it powers up. • The running time hour meters are then displayed briefly. • The standard display automatically scrolls through all configured zones showing each zone for 10 seconds. Horizontal bars indicate the current zone being displayed; One bar = Zone 1, Two bars = Zone 2 and Three bars = Zone 3. • The diesel engine will preheat and start as required when the unit is turned on. On SmartPower equipped units, the electric standby motor will start if the unit is connected to standby power. To turn a Zone on or off: 1. Press the ENTER key to put the unit in Manual Zone Selection mode. • A decimal point will appear to the right of the horizontal bar indicating the Manual Zone Selection Mode is active. 2. Press the ENTER key again as require to select the desired zone. 3. When the desired zone is selected, simultaneously press the ON key and the ENTER key to turn the zone off. • The box temperature and setpoint temperature will now show all dashes indicating the zone is turned off. 4. Simultaneously pressing the ON key and ENTER key again will turn the selected zone back on. 5. Press the Off key to turn the unit off. • The unit will immediately shut off and the display will go blank. Simple to Set: CYCLE-SENTRY™ or Continuous Run 1. Press the CYCLE-SENTRY/Continuous key to change from CYCLE- SENTRY to Continuous mode. • Amber LED indicates the unit is operating in CYCLE-SENTRY mode. • No LED illuminated indicates the unit is operating in Continuous mode. Simple to Set: Setpoint Temperature 1. Press the ENTER key to put the unit in Manual Zone Selection mode. 2. Press the ENTER key again as required to select the desired zone. 3. When the desired zone is selected, press the UP or DOWN arrow keys until the desired setpoint is shown. 4. Press the ENTER key to confirm the new setpoint. Simple to Defrost: Initiate Manual Defrost 1. Press the ENTER key to put the unit in Manual Zone Selection mode. 2. Press the ENTER key again as required to select the desired zone. 3. Press the DEFROST key to initiate a manual defrost cycle in the selected zone. • Amber LED next to the DEFROST key indicates the unit is in defrost in the selected zone. NOTE: The defrost cycle terminates automatically when the evaporator coil reaches a predetermined temperature or when the defrost timer expires. Defrost can also be terminated by turning the unit off and back on. Simple to Check: Pretrip Test FULL PRETRIP TEST NOTE: Full Pretrip must be done with the unit not running. 1. Turn the unit on, clear all alarm codes and turn the unit off. 2. Turn the unit on again and wait for the unit running time hourmeters to be displayed. Once the hourmeters are displayed, press and hold the PRETRIP key for 5 seconds. • Flashing LED indicates that the Pretrip is being initialized. • Steady amber LED indicates the Pretrip is in process. • Full Pretrip Test typically lasts 20 to 30 minutes. • The amber LED will turn off when the Pretrip Test is complete or if a Shutdown Alarm occurs. ENGINE RUNNING PRETRIP TEST NOTE: Engine Running Pretrip Test must be done with the unit running. 1. Turn the unit on, clear all alarm codes and allow the unit to start. 2. With the unit running, press and hold the PRETRIP key for 5 seconds. • Flashing LED indicates that the Pretrip is being initialized. • Steady amber LED indicates the Pretrip is in process. • Full Pretrip Test typically lasts 20 to 25 minutes. • The amber LED will turn off when the Pretrip Test is complete or if a Shutdown Alarm occurs. To stop a Pretrip Test at any time, press the OFF key to turn the unit off. This will generate a Alarm Code 28 Pretrip Abort. PRETRIP TEST RESULTS Pass Pretrip Test • If the unit passes the Pretrip Test, the amber Pretrip Test LED will turn off at the completion of the test and the unit will continue to run as required. Fail Pretrip Test with Check Alarms • If the unit fails the Pretrip Test with Check Alarms, the Alarm Icon will appear when the alarm condition occurs. The Pretrip Test will continue to run unless a Shutdown Alarm occurs. See Operator’s Manual for more information regarding alarm codes.

Simple to Start: One or Multiple Zones 1. Press the ON key to turn the unit on. • The Thermo King Logo will briefly be displayed as the system initializes. • CONFIGURING SYSTEM PLEASE WAIT briefly appears while communications are established and the unit prepares for operation. • The Standard Display showing box temperatures and setpoints briefly appears next. • DIESEL ENGINE STARTING appears as the engine preheats and starts. On SmartPower equipped units, ELECTRIC MOTOR STARTING will appear if the unit is connected to standby power. • The Standard Display showing box temperatures and setpoints appears while the unit is running. 2. Press the OFF key to turn the unit off. The unit will immediately shut off and SYSTEM IS POWERING DOWN will appear briefly. To turn a Zone on or off: Zone 1 will always be displayed any time the unit is turned on. Zone 2 and Zone 3 (if present) can be turned on and off as desired. 1. Return to the Standard Display (press any key to return to the Standard Display). 2. Press the ZONE key under the desired zone. • The setpoint display appears. If the zone is turned on, the third key will be labeled Turn Zone Off. If the zone is turned off, the third key will be labeled Turn Zone On. 3. Press the TURN ZONE OFF key to turn the zone off. • The display briefly shows PROGRAMMING ZONE ON/OFF - PLEASE WAIT. • The display will confirm the new Zone setting for several seconds. • The display will return to the Standard Display showing the Zone is off. The setpoint for the Zone has been replaced with OFF to indicate that the zone is now off. Simple to Set: CYCLE-SENTRY™ or Continuous Run 1. From the Standard Display, press the MENU key to display the MODE menu. 2. When the MODE Menu is shown press the SELECT key. • TURN OFF CYCLE SENTRY or TURN ON CYCLE SENTRY will appear. 3. Press the SELECT key to change the mode. • The new mode is confirmed for 10 seconds followed by NEW SYSTEM MODE IS (Cycle Sentry or Continuous). 4. Once the display returns to Mode Menu, press EXIT key to return to the Standard Display. 5. Press the SELECT key again to change the unit back to the previous mode. Simple to Set: Setpoint Temperature 1. From the Standard Display, press the ZONE key for the desired zone (example: Zone 2 is shown). • The setpoint display will appear for the selected Zone. 2. Press the + or - keys to change the setpoint reading. 3. Press the YES or NO key accordingly. • PROGRAMMING NEW SETPOINT - PLEASE WAIT will appear. • NEW SETPOINT WILL BE XX appears briefly. • The Standard Display appears with Zone setpoint changed to the new setpoint. Simple to Check: Gauges 1. From the Standard Display, press the MENU key. 2. Press the NEXT key until the Gauges Menu appears. 3. Press the SELECT key to enter the Gauges Menu. 4. Press the BACK or NEXT keys to scroll through the available gauges. 5. Press the LOCK key to display any gauge screen for an indefinite period. 6. Press the LOCK key again to unlock the screen. 7. Press the EXIT key to return to the Standard Display. Simple to Defrost: Initiate Manual Defrost 1. From the Standard Display, press the DEFROST key. • DEFROST will briefly be displayed followed by SELECT ZONE TO DEFROST. 2. Press the SELECT key for desired zone (example: Zone 1 is shown). • The display will briefly show DEFROST, followed by PROGRAMMING DEFROST - PLEASE WAIT and then DEFROST STARTED. • The bar indicator shows approximate percentage of time remaining to complete defrost cycle. NOTE: The defrost cycle terminates automatically when the evaporator coil reaches a predetermined temperature or when the defrost timer expires. Defrost can also be terminated by turning the unit off and back on. Simple to Check: Sensors 1. From the Standard Display, press the MENU key. 2. Press the NEXT key until the Sensors Menu appears. 3. Press the SELECT key to enter the Sensors Menu. 4. Press the NEXT or BACK keys to scroll through the sensors. 5. Press the LOCK key to display any sensor screen for an indefinite period. 6. Press the LOCK key again to unlock the screen. 7. Press the EXIT key to return to the Standard Display. Simple to Check: Pretrip Test 1. Clear all alarm codes. 2. From the Standard Display, press the MENU key. 3. Press the NEXT key until the PRETRIP Menu appears. 4. Press the SELECT key. • FULL PRETRIP will be initiated if the unit is not running. • RUNNING PRETRIP will be initiated if the unit is running on either diesel or electric standby. When all tests are complete, the results are reported as PASS, CHECK or FAIL. If the results are CHECK or FAIL, the accompanying alarm codes will direct the technician to the cause of the problem.