Thompson roc 4306 Manuals

The ROC 4306 is a universal remote control (4 in 1). It can replace 4 remote controls thanks to its 4 mode keys TV, VCR/DVD... It is compatible with the majority of television sets, video cassette recorders, DVD players, satellite and cable receivers as well as terrestrial digital television (DVBT), amplifiers and other audio equipment provided they are controlled by infra red signals. This remote control has been factory programmed to allow you to use it immediately with the majority of Thomson Group devices.We therefore advise you to try it before beginning to program it. If programming is necessary, follow one of the methods A, B, C, D or E that are given in this manual. But first, install 2 batteries (AAA) in the remote control. Keep these instructions and the separate list of codes in a safe place so that you can later reprogram your remote control. 1 Indicator lamp: the red indicator lamp lights up when any key is pressed. 2 B: On / Standby. 3 Remote control mode Selects device to control TV, DVD,VCR,... 4 B (Play): play*. 5 F (FF): fast forward *. 6 L (STOP): stop playback*. 7 K (Pause): stops on an image*. 8 I (EXIT): teletext Off in TV mode. SHIFT and EXIT: turns off the menu of the selected product. 9 VOL-/VOL+ increases (+) or decreases (-) the volume of the TV set. SHIFT and VOL-/VOL+ also allows you to navigate the menus horizontally. 10 S: programmes the remote control. SHIFT: activates the secondary key features (indications in blue). 11 Number keys 0 to 9: these keys have the same functions as those of your original remote and are also used to enter the codes for different products. 12 Press this key first before you type in the 2-digit channel number (except for Thomson group products). 13 AV: for selecting an external source (SCART). 14 c: switches the TV sound off. SHIFT and OK: confirms a selection. 15 PROG+,PROG-: programmes zapping button (received by the television set or the satellite receiver); use to scroll vertically through menus SHIFT and PROG+/PROG- also allow you to navigate the menus vertically. 16 a (MENU): teletext On/Off in TV mode. SHIFT and MENU: turns on the menu of the selected products. 17 M (RECORD): to record. 18 G (REW): goes backward or advances forward*. * The coloured buttons can be used to select categories when teletext is activated, and specific functions depending on the make. 2 - Testing the remote control before programming 1 1. Turn on the device that you wish to control. 2. Press the key corresponding (3) to the type of device to control: TV: television set, VCR/DVD: video cassette recorder, DVD player, DVB-T: DVBT receiver, SAT: satellite. 3. Point the remote control at the device you wish to control and try to turn it off using theB (2) key. If the device does not turn off, you must program the remote control using one of the methods A, B, C or D as described below. 1 - Description of keys 3 - Programming the remote control Before you start programming, you must find the subcode of the set to be controlled. Refer to the list provided with these instructions, page I of the codes. 1 Switch on the set you want to control. 2. Hold down the S (10) key until the red indicator lamp (1) remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes when this time is almost up, and then goes off). 3. Press the key (3) that corresponds to the type of equipment you want to control: TV: television set, VCR/DVD: video cassette recorder, DVD player, DVB-T: DVBT receiver, SAT: satellite. 4. While the indicator is lit, type in the subcode (example: 1 for Thomson). 5. Direct the remote control towards the set and try to switch it off by pressing the B (2) key. 6. If the set you want to control switches off, press c (14) to memorise the subcode. 7. If the product doesn’t turn off, press the B (2) key repeatedly until the set switches off. Wait approximately one second between key presses to give the red indicator lamp (1) enough time to go off and light up again. This will allow you to see whether the product responds or not. 8. Immediately upon the switching-off of the set to be controlled, press c (14) to store the subcode. Note: If you want to assign another type of product than those mentioned on the remote control (with the exception of the TV button which can only be used to control a television set), begin by entering the code that corresponds to the product you want to programme (a 4-digit code that you will find in the code booklet – see method B). Example: if you want to control a satellite receiver with the VCR/DVD key, begin by entering a satellite code (any satellite, for example: 0603 for a Thomson satellite receiver) then begin the procedure. Check of the programming: In principle, your set is ready for receiving the remote control commands. Check your remote control for proper functioning by performing the test described on page 3. Method A – Fast programming with 1-digit subcode 1 GB 1 01_ROC4306_GB.indd 1 8/12/06 9:50:20