Toro 38622 Manuals

Form No. 3353-595 Rev A Power Max™826LE Snowthrower Model No. 38622—Serial No. 260000001 and Up Operator's Manual Introduction Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely. You may contact Toro directly at www.Toro.com for product and accessory information, help finding a dealer, or to register your product. Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product. Write the numbers in the space provided. Figure 1 1. Model and serial number location Model No. Serial No. This manual identifies potential hazards and has safety messages identified by the safety alert symbol (Figure 2), which signals a hazard that may cause serious injury or death if you do not follow the recommended precautions. Figure 2 1. Safety alert symbol This manual uses 2 other words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention. Warning CALIFORNIA Proposition 65 Warning The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. This spark ignition system complies with Canadian ICES-002 The enclosed Engine Owner’s Manual is supplied for information regarding the US Environmental Protection Agency (EPA) and the California Emission Control Regulation of emission systems, maintenance, and warranty. Replacements may be ordered through the engine manufacturer. © 2005—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Register at www.Toro.com. Original Instructions (EN) Printed in the USA All Rights Reserved

Form No. 3353-932 Rev A Power Max™ 828LXE Snowthrower Model No. 38630—Serial No. 260000001 and Up Operator's Manual Introduction Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely. You may contact Toro directly at www.Toro.com for product and accessory information, help finding a dealer, or to register your product. Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product. Write the numbers in the space provided. G000982 1 Figure 1 1. Model and serial number location Model No. Serial No. This manual identifies potential hazards and has safety messages identified by the safety alert symbol (Figure 2), which signals a hazard that may cause serious injury or death if you do not follow the recommended precautions. Figure 2 1. Safety alert symbol This manual uses 2 other words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention. Warning CALIFORNIA Proposition 65 Warning The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. This spark ignition system complies with Canadian ICES-002 The enclosed Engine Owner’s Manual is supplied for information regarding the US Environmental Protection Agency (EPA) and the California Emission Control Regulation of emission systems, maintenance, and warranty. Replacements may be ordered through the engine manufacturer. © 2005—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Register at www.Toro.com. Original Instructions (EN) Printed in the USA All Rights Reserved

2005 by The Toro Company 8111 Lyndale Ave., Bloomington, MN 55420, USA Printed in the USA All Rights Reserved Original Instructions (EN) Register your product at www.toro.com PowerMax Snowthrower Model No. 38622 Form No. 3353-603 Rev B Setup Instructions Important: Refer to your Operator’s Manual for safety, maintenance, and warranty information. Setup 1. Position the upper handle over the lower handle. Note: Do not remove the rubber band until you have installed the handle. Important: Route the 2 cables attached to the Quick Stick (A) inside the upper handle legs. Do not pinch the cables or the headlight wire. m-7698 A 2. Secure the upper handle (fasteners are shown above). 3. Remove the hairpin cotter and washer from the end of the speed control rod (B) and insert the end into the lower link arm (C). 4. Secure the rod end with the washer and hairpin cotter. m-6899 C B 5. Remove the hairpin cotter and the outer washer from the trunnion (D) on the upper end of the speed control rod. m-6898a F E D G Note: Do not remove the wave washer (E) or the flat washer (F). 6. Shift the speed selector lever into Position R2. 7. Rotate the lower link arm up. m–6971 8. Lift up the speed control rod and insert the trunnion in the hole in the speed selector lever (see G above) located under the control panel. Note: If the trunnion does not fit into the hole when you lift up the speed control rod, rotate the trunnion up or down on the speed control rod until it fits. 9. Secure the trunnion and upper end of the speed control rod with the outer washer and a hairpin cotter. Note: For easier installation, look down through the opening in the speed selector (H). m-6972 H 10. Unwrap the Quick Stick and rotate it so that it is upright and in the center. 11. Hold the blue cap down and pull the lever fully back. Note: The discharge chute and deflector should face forward. If they do not, hold the blue cap down (but do not move the Quick Stick), and rotate the discharge chute until they do. 12. Align the flattened end of the long rod (I) with the flattened end of the short rod (J) that extends from the control panel so they nest together. m-6969 I J m–6973 13. Insert the long rod end into the back of the chute gear cover until it slides into the gear. 14. Align the holes in the nested ends of the rods and insert 2 bolts through the short rod from the left side (from the operating position). 15. Insert the cable clip (K) that supports the deflector cable (L) on the forward bolt (M), and secure the bolts with the locknuts provided. K L M 16. Hold the blue cap down and rotate the Quick Stick in a circle to ensure that the chute and deflector work smoothly. 17. Insert the wire connector on the loose end of the wire straight into the back of the headlight. 18. Secure a cable tie around the wire and the handle about an inch (2.5 cm) below the U-bolt. m-7011