Toyota 00016-34088 Manuals

TOYOTA TUNDRA 2015 Billet Grille w/LED DRL Part Number: 00016-34088 Accessory Code: BG3000 Conflicts Models 1794 and Platinum Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3 1 Switch 4 1 5 2 Hardware bags 6 1 Grille Assy 7 1 Logo Plate SR5 8 1 Logo Plate Limited DRL Hardware Bag Contents Item # Quantity Reqd. Description 1 1 Relay 2 1 Hood Wire Harness 3 1 Cabin Wire Harness 4 8 Wire ties 5 2 Black T-Taps Grille Hardware Bag Contents Item # Quantity. Description 1 6 U-Nuts 2 8 #10 Screws 3 2 #8 Screws 4 2 5 2 Top Plate Extension Brackets (LH/RH) 6 2 Middle Extension Brackets (LH/RH) 7 2 Bottom Extension Brackets (LH/RH) 8 4 9 3 10 2 Recommended Tools Safety Tools Safety Glasses Electrical Tape Installation Tools 10mm Wrench Phillips Screw Driver Pliers Side Cutters Torque Wrench 48" lbs Special Chemicals 3M Silicon Sealant DRL Accessory Service Parts Service Part LED DRL LH LED DRL RH Switch Relay Wire Harness Driver box Part Number 00016-32290-01 X 00016-32290-02 X 00016-32270-05 X 00016-32260-04 X 00016-32270-03 X 00016-32270-06 X Grille Accessory Service Parts Service Part Hardware Kit (Black) Logo Mount Plate (Black) Part Number 00016-34088-01 X 00016-34064-02 X Recommended Sequence of Application Item # Accessory 1 LED DRL 2 Billet Grille Mandatory Legend Southeast Toyota Distributors, LLC Page 1 of 16 Doc. 15.215.00 Business Partner: J55 PIO / DIO Rev. A 01/07/15 TOYOTA TUNDRA Billet Grille w/LED DRL Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure quality installation. These guidelines can be found in the Accessory Installation Practices document. This document covers such items as: • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc) • Safety (eye protection) • Vehicle Disassembly / Reassembly (panel removal, part storage, etc) Preparation Remove negative battery cable Installation 1. From front of vehicle, lay the DRL’s wire harness on the engine compartment, left side from the battery towards the firewall of the car (pictures A and B). Picture A Picture B 2. Locate the large vehicle harness grommet on the left side. If accessible, cut the auxiliary wiring access nipple off the grommet or cut ¼” slit in grommet and push the red, black, black-white and red-white wires through firewall. Note: Extra caution should be taken not to damage the connector’s pin. Seal with 3M Silicone sealant (picture 1) Southeast Toyota Distributors, LLC Page 2 of 16 TOYOTA TUNDRA Billet Grille w/LED DRL Picture 1 Vehicle Disassembly 3. Remove driver side door scuff plate. Disengage with panel tool and remove (picture 2 and 2A) Picture 2 Picture 2A 4. Remove the driver side cowl side trim (pictures 3 and 3A) Picture 3 Picture 3A 5. Remove the driver’s side lower dash panel: remove two lower screws (picture 4) Picture 4 6. From inside the cabin, locate the wires that were pushed through in step 2. It will be the Southeast Toyota Distributors, LLC Page 3 of 16