TP-Link TR-965DA Manuals

Position two converters back to back between the following end devices. Installation Procedure 1. Converter to 10/100Base-TX Device (hub or switch) Connection Make sure that the length of twisted pair cable (Category-5) between 10/100Base-TX device and converter is no longer than 100 meters. Connect one end of twisted pair cable to RJ45 jack on the converter and the other end of the cable to the RJ45 jack on the 10/100Base-TX device. 2. Converter to Converter or 100Base-FX Device Connection Connect one (SC) end of a fiber cable to the SC connector on the converter and the other end of the cable to the SC ! ! 5 2 1 3 4 6 7 TR-965DA TR-965DB User's Guide 71030498 Rev 1.0 10/100Mbps Fast Ethernet Converter Table of Contents Introduction...............................................................................2 Features....................................................................................2 Network Cable Supported..........................................................3 Package Contents.....................................................................3 Appearance Indication...............................................................4 Installation Guide......................................................................5 Appendix Specifications...........................................................7 Introduction The TR-965DA/TR-965DB are 10/100Mbps Fast Ethernet converter. The converter mediates between a 10/100Base-TX segment and a 100Base-FX segment.It is primarily designed for large, more high speed/bandwidth demanding workgroups that require expansion of the Fast Ethernet network. Features Complies with IEEE802.3u 10Base-T, 100Base-TX and 100Base-FX standard. Provide one SC fiber connector and one UTP connector. The SC fiber connector can transfer and receive data on one single-mode fiber. Provide switch configuration of half/full duplex transfer mode for FX port. Extend fiber distance up to 20-60km for single-mode fiber. ! ! ! ! ! AC power connector RJ45 connetor SC fiber connetor ! ! ! Easy-to-view LED indicators provide status to monitor network activity easily. External power adapter supply. Network Cable Supported The connectors and network cables supported by the converter are listed in the following: UTP: Cat 5 Twisted-Pair Fiber SC: 1300nm 62.5/125 Single-mode Fiber Package Contents Before start using the products, make sure that what you have is what you ordered. The Converter includes: One Converter TR-965DA-20 RJ45--SC 20km Single-mode Fiber,Cat-5 TR-965DA-40 RJ45--SC 40km Single-mode Fiber,Cat-5 TR-965DA-60 RJ45--SC 60km Single-mode Fiber,Cat-5 TR-965DB-20 RJ45--SC 20km Single-mode Fiber,Cat-5 TR-965DB-40 RJ45--SC 40km Single-mode Fiber,Cat-5 TR-965DB-60 RJ45--SC 60km Single-mode Fiber,Cat-5 Type Connetor Transmission Distance Transmission Media ! ! ! ! ! ! ! One AC adapter This User's Guide Appearance Indication LED Indicators This converter has LED indicators which can provide a real-time report. When you take a look at these indicators, you will know what's happening on your network. Power(green) Lights when the adapter is properly plugged in. TX_SPD(green) Lights when the UTP ports is connected to 100Base-Tx device. TX_LINK/ACT(green) Steady green indicates that a valid link exists. Flashing green indicates that the converter is receiving data or transmitting data from the RJ45 connector. FX_LINK/ACT(green) Steady green indicates that a valid link exists. Flashing green indicates that the converter is receiving data or transmitting data from the Fiber Optic connector. FX_FDX/COL(green) Steady green indicates that the fiber optic connector is operating in full-duplex mode. The light is off Which means that the fiber optic connector is operating in half-duplex mode. Flashing green indicates for collision. FDX/HDX Switch FDX: The UTP port operate in full-duplex mode ; HDX: The UTP port operate in haf-duplex mode; Notice: You must reset the converter when you achieve the configuration. Installation Guide SC fiber connector works at 1550nm on transferring data and at 1310nm on receiving data in one single-mode fiber. SC fiber connector, inversely, works at 1310nm on transferring data and at 1550nm on receiving data in a fiber. So the Configuration In order to achieve the aim of effectively expanding a Fast Ethernet network, You can use the converter for the example : ! ! TR-965DA's TR-965DB's TR-965DA and the TR-965DB must use as partnership together. 10/100Base-TX interface 10/100Base-TX interface 100Base-FX interface Twisted-pair Twisted-pair Single fiber Device A Device B TR-965DA TR-965DB connector on the other converter or 100Base-FX device. 3. Turn on the power Appendix Specifications Standard: IEEE 802.3/IEEE 802.3u Connector: 1 SC fiber optic; 1 RJ45 jack Max. Distance: Twisted Pair(Cat5):100m Single-mode Fiber Optic: 20km Power: external power adapter supply, AC 9V~ 0.8A O O O O Temperature: Operation: 0 C~40 C (32 F~104 F) O O O O Storage: -40 C~70 C (-40 F~158 F) Humidity: 10%-90% (non-condensing) Dimensions(LxWxH): 4.84x2.64x0.94 in.(123mmx67mmx24 mm) FDX HDX 9V~ 50Hz 0.8A UTP