Transition Networks C/AR-CF-02SC Manuals

MEDIA CONVERTER TECHNICAL SPECIFICATIONS Standards ANSI/ATA 878 Delay 300ns one-way Case dimensions 4.75" x 3.0" x 1.0" (119mm x 76mm x 25mm) Shipping Weight 2 pounds (0.9 kilograms) Environment Temperature: 0-40°C (32° to 104° F ) Humidity 10-90%, non condensing Altitude 0-10,000 feet Warranty Five years CAUTION: Wear a grounding device and observe electrostatic discharge precautions when installing Media Converter Slide-in-Module(s) in the Media Conversion Center. Failure to observe this caution could result in damage to, and subsequent failure of, the Media Converter Slide-in- Module(s). NOTE: Media Converter Slide-in-Modules can be installed in any installation slot, in any order. Compliance Information UL Listed C-UL Listed (Canada) CISPR/EN55022 Class A FCC Regulations This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at the user’s own expense. Canadian Regulations This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio interference regulations of the Canadian Department of Communications. European Regulations Warning This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Copyright Restrictions © 1999 TRANSITION Networks. All rights reserved. No part of this work may be reproduced or used in any form or by any means – graphic, electronic, or mechanical – without written permission from TRANSITION Networks. Trademark Notice ARCNET is a registered trademark of Datapoint Corporation. All registered trademarks and trademarks are the property of their respective owners. 33096.A The TRANSITION Networks ARCNET® Coax Copper/Fiber Media Converter (series C/AR-CF-02), designed to be installed in the TRANSITION Networks Media Conversion Center, E-MCC-1600, extends the signal distance of an ARCNET® segment or node link up to 2 kilometers over fiber*, up to 600 meters over coax cable in a star topology, and up to 300 meters over coax cable in a bus topology. A switch on the media converter allows the media converter to terminate the link or node signal. STATUS LEDS Power Steady green LED indicates connection to external AC power. Coax Blinking green LED indicates network traffic on coaxial cable link. Fiber Blinking green LED indicates network traffic on fiber link. *Consider carefully the network constraints imposed by the maximum latency response time of installed equipment. Some equipment cannot handle the extended response time that 2 kilometers of fiber introduces. Minneapolis, MN 55344 USA ARCNET® Coax Copper/Fiber Slide-In-Module Media Converters C/AR-CF-02, C/AR-CF-02(SC), C/AR-CF-02(SM) USER’S GUIDE 10BASE-T RX TX Fiber Power Coax C/AR-CF-02 Provides a BNC connector to coaxial cable and a set of RX (receive) and TX (transmit) ST connectors to multimode fiber-optic cable. C/AR-CF-02(SC) Provides a BNC connector to coaxial cable and an RX (receive) and TX (transmit) SC connector to multimode fiber-optic cable. C/AR-CF-02(SM) Provides a BNC connector to coaxial cable and an RX (receive) ST and TX (transmit) SC connector to singlemode fiber-optic cable. Power Modules Media Conversion Center E-MCC-1600 Power In Use Power In Use 1 2 Management Module Power Link TX RX Fiber Multimode - to 2 kilometers Singlemode - to 8 kilometers Coax STAR - to 600 meters (no minimum) BUS - to 300 meters (1.8 meter minimum