Transition Networks CFMFF1314-280 Manuals

Installation . . . . . . . . . . . . . . . . . . .2 Operation . . . . . . . . . . . . . . . . . . .6 Cable Specifications . . . . . . . . . . . .7 Technical Specifications . . . . . . . .8 Troubleshooting . . . . . . . . . . . . . . .9 Contact Us . . . . . . . . . . . . . . . . . .11 Compliance Information . . . . . . .12 Unless otherwise indicated, the distances listed are the typical maximum cable distance. The actual maximum cable distances are dependent upon the physical characteristics of the network installation. ** Minimum Cable Distance: 2 meters Typical Maximum Cable Distance: 220 meters for 160/500MHz•Km 270 meters for 200/500MHz•Km CFMFF13xx-28x User’s Guide Single Mode to Multimode Retiming Media Converter • Slide-in-Module Media Converter • Gigabit Ethernet Transition Networks CFMFF13xx-28x series media converters extend multimode interfaces over gigabit Ethernet fiber optic cable. The CFMFF13xx-28x is also designed to be installed into the Transition Networks PointSystem™ chassis. Unlike most gigabit Ethernet media converters, which allow only two media converters in series, the CFMFF13xx-28x has a retiming/reshaping feature that makes it possible to connect any number of media converters in series. Part Number Port One - Duplex Fiber Optic 1000Base-SX Port Two - Duplex Fiber-Optic 1000Base-LX CFMFF1314-280 SC, 850 nm multimode 220 m (721 ft)** SC, 1310 nm single mode 10 km (6.2 miles) CFMFF1315-280 SC, 850 nm multimode 220 m (721 ft)** SC, 1310 nm single mode 25 km (15.5 miles) CFMFF1317-280 SC, 850 nm multimode 220 m (721 ft)** SC, 1550 nm single mode 65 km (40.3 miles) CFMFF1324-280 SC, 850 nm multimode 220 m (721 ft)** SC, 1300 nm multimode (1000Base-SX) 2 km (1.2 miles) (62.5 / 125 mm fiber only) CFMFF1335-280 SC, 850 nm multimode 220 m (721 ft)** SC, 1550 nm single mode 125 km (77.5 mi) CFMFF3535-280 SC, 1550 nm single mode 125 km (77.5 mi) SC, 1550 nm single mode 125 km (77.5 mi) NOTE: The SFMFF13xx-28x model is the stand alone version of the media converter. For more information, see the user’s guide on-line at: www.transition.com. Port One - Duplex Fiber Optic 1000Base-SX Port Two - Single Mode Fiber-Optic Single Fiber, 1000Base-LX 2 CFMFF13xx-28x 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 Part Number CFMFF1329-280 SC, 850 nm multimode 220 m (721 ft)** SC, 1310 nm (TX)/1550 nm (RX) 20 km (12.4 miles) CFMFF1329-281 SC, 850 nm multimode 220 m (721 ft)** SC, 1550 nm (TX)/1310 nm (RX) 20 km (12.4 miles) CFMFF1329-280 and CFMFF1329-281 are intended to be installed in the same network where one is the local converter and the other is the remote converter. CFMFF1329-282 SC, 850 nm multimode 220 m (721 ft)** SC, 1310 nm (TX)/1550 nm (RX) 40 km (24.8 miles) CFMFF1329-283 SC, 850 nm multimode 220 m (721 ft)** SC, 1550 nm (TX)/1310 nm (RX) 40 km (24.8 miles) Unless otherwise indicated, the distances listed are the typical maximum cable distance. The actual maximum cable distances are dependent upon the physical characteristics of the network installation. TX = transmit, RX = receive. ** Minimum Cable Distance: 2 meters Typical Maximum Cable Distance: 220 meters for 160/500MHz•Km 270 meters for 200/500MHz•Km CFMFF1329-282 and CFMFF1329-283 are intended to be installed in the same network where one is the local converter and the other is the remote converter. Installation CAUTION: Wear a grounding device and observe electrostatic discharge precautions when setting the jumper, the 4-position switch, and when installing the slide-in-module. Failure to observe this caution could result in damage to, and subsequent failure of, the media converter. Set the Hardware/Software Jumper • The jumper is located on the circuit board. • Use small needle-nose pliers to set the recessed switches. Hardware The media converter mode is determined by the 4-position switch settings (see page 4). Software The media converter mode is determined by the most-recently saved, on-board microprocessor settings. (See SNMP on page 6.) CFMFF1414-280 SC, 1310 nm single mode 10 km (6.2 miles) SC, 1310 nm single mode 10 km (6.2 miles) 3 [email protected] -- Click the “Transition Now” link for a live Web chat. Installation -- Continued Set the 4-position switch • The 4-position switch is located on the circuit board. • Use a small flat-blade screwdriver to set the recessed switches. Fiber Auto-Negotiation (Switch 1) up = Enable fiber Auto-Negotiation for both the single mode and the multimode ports. When fiber Auto-Negotiation is enabled: The pause feature can be set using switches 3 and 4. (See page 4). down = Disable fiber Auto-Negotiation for both the single mode and the multimode ports. When fiber Auto-Negotiation is disabled: Switches 3 and 4 will not function. The media converter adopts the pause setting from the end device at the other end of the fiber cable. NOTE: All devices in the network, including the end devices, must have Auto-Negotiation enabled, or all devices must have Auto-Negotiation disabled. Otherwise, the devices in the network will not link up. Link Pass-Through (Switch 2) up = Enable Link Pass-Through. down = Disable Link Pass-Through. The Link Pass-Through feature allows the media converter to monitor both fiber RX (receive) ports for loss of signal. In the event of a loss of an RX signal on one media port, the media converter will automatically disable the TX (transmit) signal of the other media port, thus, “passing through” the link loss. No Pause: • Pause feature is disabled. Transmit Only: • CFMFF13xx-28x can transmit and the link partner can receive the pause signal. Transmit and Receive: • Both the CFMFF13xx-28x and the link partner can send and receive the pause signal. Receive Only: • The CFMFF13xx-28x can receive and the link partner can transmit the pause signal. Installation -- Continued Pause (Switches 3 & 4) The pause feature can improve network performance by allowing one end of the link to signal the other to discontinue frame transmission for a set period of time to relieve buffer congestion. To properly set the pause feature in the network, the link partner (i.e., the device to which the CFMFF13xx-28x is linked) must also have comparable pause switches. If the link partner does not have the pause feature, disable the pause feature on the CFMFF13xx-28x media converter. The CFMFF13xx-28x has four pause options (listed below). To the right of each option, a drawing shows the switch settings for the CFMFF13xx-28x and the link partner. 4 CFMFF13xx-28x 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 5 [email protected] -- Click the “Transition Now” link for a live Web chat. Install the Fiber Cable 1. Locate or build IEEE 802.3™ compliant fiber cable with male, two- stranded TX to RX connectors installed at both ends. 2. Connect the fiber cables to the CFMFF13xx-28x media converter as described: • Connect the male TX cable connector to the female TX port. • Connect the male RX cable connector to the female RX port. 3. Connect the fiber cables to the other device (another media converter, hub, etc.) as described: • Connect the male TX cable connector to the female RX port. • Connect the male RX cable connector to the female TX port. Installation -- Continued Install the CFMFF13xx-28x Slide-in-Module CAUTION: Slots in the PointSystem™ chassis without a slide-in-module installed MUST have a protective plate covering the empty slot for Class A and/or Class B compliance. The media converter slide-in-modules may be installed in any slot, in any order. To install the CFMFF13xx-28x slide-in-module: 1. Carefully slide the slide-in-module into the installation slot, aligning the module’s circuit board with the installation guides. 2. Ensure that the module is firmly seated inside the chassis. 3. Push in and rotate the attached panel fastener screw clockwise to secure the module to the chassis front. 6 CFMFF13xx-28x 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 SNMP Use SNMP at an attached terminal or at a remote location to monitor the media converter by monitoring: • Media converter power • Single mode fiber link status • Multimode fiber link status • Hardware/software mode status Also, use SNMP to enter network commands that: • Power up/down the media converter • Enable/disable the single mode fiber link • Enable/disable the multimode fiber link • Enable/disable Auto-Negotiation • Enable/disable Link Pass-Through • Select pause advertisements See the on-line documentation that comes with Transition Networks FocalPoint™ software for applicable commands and usage at www.transition.com. Operation Status LEDs Use the status LEDs to monitor the media converter operation in the network. PWR On = Connection to external power. LKS On = 1000Base-LX (single mode) fiber link is up. LKM On = 1000Base-SX (multimode) fiber link is up. ACT Flashing = Reception of data on either fiber link. 7 [email protected] -- Click the “Transition Now” link for a live Web chat. Cable Specifications The physical characteristics must meet or exceed IEEE 802.3™ specifications. Single Mode fiber (recommended): 9 µm Multimode fiber (recommended): 62.5/125 µm Multimode fiber (optional): 100/140, 85/140, 50/125 µm Bit error rate: <10-12 Port 1: 1300 nm multimode Fiber-optic Transmitter Power: min: -10.0 dBm max: -4.0 dBm Fiber-optic Receiver Sensitivity: min: -17.0 dBm max: 0.0 dBm Link Budget: 7.0 dB Port 2: CFMFF1314-280 1310 nm single mode Fiber-optic Transmitter Power: min: -13.0 dBm max: -3.0 dBm Fiber-optic Receiver Sensitivity: min: -20.0 dBm max: -3.0 dBm Link Budget: 7.0 dB CFMFF1315-280 1310 nm single mode Fiber-optic Transmitter Power: min: -5.0 dBm max: 0.0 dBm Fiber-optic Receiver Sensitivity: min: -20.0 dBm max: -3.0 dBm Link Budget: 15.0 dB CFMFF1317-280 1550 nm single mode Fiber-optic Transmitter Power: min: -3.0 dBm max: +2.0 dBm Fiber-optic Receiver Sensitivity: min: - 23.0 dBm max: -3.0 dBm Link Budget: 20.0 dB CFMFF1324-280 1300 nm extended multimode Fiber-optic Transmitter Power: min: -10.0 dBm max: -3.0 dBm Fiber-optic Receiver Sensitivity: min: -17.0 dBm max: -3.0 dBm Link Budget: 7.0 db CFMFF1329-280 1310 nm (TX) / 1550 nm (RX) single mode Fiber-optic Transmitter Power: min: -8.0 dBm max: -3.0 dBm Fiber-optic Receiver Sensitivity: min: -21.0 dBm max: -3.0 dBm Link Budget: 13.0 dB CFMFF1329-281 1550 nm (TX) / 1310 nm (RX) single mode Fiber-optic Transmitter Power: min: -8.0 dBm max: -3.0 dBm Fiber-optic Receiver Sensitivity: min: -21.0 dBm max: -3.0 dBm Link Budget: 13.0 dB CFMFF1329-282 1310 nm (TX) / 1550 nm (RX) single mode Fiber-optic Transmitter Power: min: -3.0 dBm max: +2.0 dBm Fiber-optic Receiver Sensitivity: min: -23.0 dBm max: -8.0 dBm Link Budget: 20.0 dB CFMFF1329-283 1550 nm (TX) / 1310 nm (RX) single mode Fiber-optic Transmitter Power: min: -3.0 dBm max: +2.0 dBm Fiber-optic Receiver Sensitivity: min: -23.0 dBm max: -8.0 dBm Link Budget: 20.0 dB CFMFF1335-280 1550 nm single mode Fiber-optic Transmitter Power: min: 0.0 dBm max: +5.0 dBm Fiber-optic Receiver Sensitivity: min: -32.0 dBm max: -3.0 dBm Link Budget: 32.0 db