Trust 1620W Manuals

TRUST 1620W WIRELESS TELEVIEWER 1 U K Instructions when using for the first time Chapter 1. Functions (3) 2. Connecting (4) 3. Using the Televiewer (5) 1 Introduction This instruction manual is for users of the TRUST 1620W WIRELESS TELEVIEWER. The TRUST 1620W WIRELESS TELEVIEWER allows you to easily change the monitor screen of your computer into a TV screen. The Televiewer operates independently and, therefore, does not depend on the operating system. The Televiewer is suitable for IBM compatible PC’s and Mac systems. The TRUST 1620W WIRELESS TELEVIEWER supports resolutions up to 1600x1200 in real colours. The composite video and S-VHS connections, together with the SCART cable and sound cable, allow you to connect your computer image and sound to virtually any TV set. This makes the Televiewer ideal for playing games and viewing DVD films on large screen televisions. The Televiewer is also very suitable for presentation purposes. 2 Safety Carefully read the following instructions before use: - The TRUST 1620W WIRELESS TELEVIEWER does not require any special maintenance. Use a slightly damp, soft cloth to clean the device. - Do not use aggressive substances, such as petrol or white spirit, to clean the device. These may harm the material. - Do not submerge the device in liquid. This may be dangerous and will damage the device. Do not use this device near water. - Make sure nothing is placed on the cable. Do not use this device in an area where the cable can become worn or damaged as a result of people walking over it. - Do not repair this device yourself. If you open this device, you may touch live components. - Under the following circumstances, have the device repaired by qualified personnel: - The cable or plug is damaged or worn. - The device has come into contact with rain, water or another liquid. - This product works at a frequency of 2,485 MHz. It is approved according to the European R&TEE guidelines and, therefore, meets the harmonized standards for use within the EU. There may be limitations for the use of this device outside of the EU. In that case, check whether this device meets local regulations. Frequency: 2414 ~ 2468 MHz, Bandwidth: 10 MHz, Power: 10 mW. - Nowadays, there are an increasing number of wireless products (video, audio, convenience, computer, etc.) which work in the same frequency range as this device. It may, therefore, be possible that the functionality of this product is limited by or is limiting for other wireless products. This can only be avoided by paying attention to the distance between products and, where possible, by changing channels. - Be careful when using wireless devices if you have a pacemaker or are dependent on other life-saving, sensitive electronic equipment, because this product transmits radio signals! ! TRUST 1620W WIRELESS TELEVIEWER 2 3 Functions The description of the functions below relates to figure 1 on the foldout page. Transmitter (Tx) Function Description 1 VIDEO IN Connection for devices such as a VCR, camcorder, DVD player, etc. 2 ANTENNA Aerial for transmitting the signal to the receiver. 3 SCAN CNVTR Connection for the VGA cable. 4 AUDIO IN Connection for the AUDIO signal input. 5 VIDEO OUT Connection for the composite video cable. 6 S-OUT Connection for the S-VHS video cable. 7 DC IN Connection for the 5VDC / 500 mA adapter. 8 POSITION Buttons for adjusting the position of the TV image (up, down, left, right). 9 POWER Button for turning the transmitter on and off. 10 VIDEO SOURCE Button for switching between the computer and, for example, your VCR or DVD player. 11 SAVE Button for saving all the new settings. 12 FINE TUNE Button for fine-tuning the TV image. 13 ZOOM Button for zooming in and out of the TV image. 14 MENU Button for switching between the various OSD (On Screen Display) menu options. 15 POWER indicator The LED indicator is lit when the Televiewer is switched on. 16 PAL Indicator The LED indicator is lit when the Televiewer is switched on in the PAL mode. 17 Switch Switch for setting the channel (1 to 4). Table 1: Transmitter (Tx) functions Receiver (Rx) Function Description 18 ANT Aerial for receiving the signal from the transmitter. 19 CH.SELECT For setting the channel (1 to 4). 20 DC IN Connection for the 5VDC/500 mA adapter. 21 VIDEO Connection for the outgoing (to the TV) video signal (yellow). 22 AUDIO R Connection for the outgoing (to the TV) right-hand AUDIO signal (red). TRUST 1620W WIRELESS TELEVIEWER 3 U K 23 AUDIO L Connection for the outgoing (to the TV) left-hand AUDIO signal (white). 24 CHANNEL indicator The LED indicator is lit when the receiver is switched on. Table 2: Receiver (Rx) functions 4 Connections Follow the instructions below to install the TRUST 1620W WIRELESS TELEVIEWER (also see figure 2). 4.1 Connecting the receiver 1. Turn off your computer, monitor and TV set. 2. Disconnect your monitor’s VGA plug (A) from the computer. 3. Connect the VGA daisychain plug (B) of the VGA cable to the VGA connection on your computer. 4. Connect your monitor’s VGA plug (A) to the VGA daisychain plug (B). 5. Connect the other end of the VGA cable (C) to the VGA connection on the TRUST 1620W WIRELESS TELEVIEWER. Note: If you connect the 1620W Wireless Televiewer to a Mac, you will need to use VGA converter plugs for the VGA connection on your computer and monitor. 6. Connect the sound cable’s 3.5 mm audio jack (D) to the speaker output on your sound card or to another audio source, such as the headset output of your DVD player. 7. Connect the power adapter to the DC-IN connection. If desired, a TV can also be connected to the transmitter using the SCART plug. There are two possibilities: • S-VHS (black 4-pin plug): For the best image quality, connect the plug (E) of the S-VHS cable to the S-VIDEO OUT connection on the Televiewer. Connect the other end (F) to your TV. • Composite video (yellow cinch plug): Connect the plug (G) of the composite video cable to the VIDEO OUT connection on the Televiewer. Connect the other end (H) to your TV. Note: Only the video signal will be transmitted. The AUDIO signal can be received by using an AUDIO splitter plug (not provided) on the AUDIO IN connection. You can plug the 3.5 mm audio jack (D) in one end and a 3.5 mm audio jack with cable (not provided) in the other, which then goes to the AUDIO IN connection on your TV.