Valterra Products Go Power! GP-SW1500TS Manuals

PURE SINE WAVE INVERTER GP-SW1500TS User Manual GP-SW1500TS © 2019 Go Power!® By Valterra Products, LLC Worldwide Technical Support and Product Information gpelectric.com Go Power! Corporate Headquarters 201-710 Redbrick St, Victoria, BC Canada V8T 5J3 Tel: 1.866.247.6527 79570_MAN_GP-SW1500TS_RevB [page 2] | gpelectric.com CFB 3 4 7 CFB 3 4 7 GP-SW1500TS is new generation power inverter equipped and AC transfer switch. GP-SW1500TS is suitable for RV, Marine and Emergency appliances • User-friendly remote control • Automatic master mechanism to eliminate single point failure and optimize reliability • Built-in ATS (Automatic Transfer Switch) and AC circuit breaker • Input & output fully isolation • Output voltage / power saving mode is selectable by DIP switch • Input Protection: Reverse Polarity (Fuse) / Under Voltage / Over Voltage Protection • Output Protection: Short Circuit / Overload / Over Temperature / Over Voltage Protection To get the most out of the power inverter, it must be installed and used properly. Please read the instructions in this manual before installation and operation of this model. Product Packaging Please safely store the packaging the GP-SW1500TS was delivered in or please recycle the packaging components as outlined below; Plastic Bag Plastic Foam Plastic Bubble Wrap LDPE Low Density Polyethylene CFB 3 4 7 CFB 3 4 7 Corrugated fiberboard Main box & Internal sleeve CFB CFB 3 4 7 Corrugated Recycles www.corrugated.org www.earth911.com/recycling-center-search-guides Local recycling centres can be found here; gpelectric.com | [page 3] 1. CONTENTS 2. GENERAL INFORMATION .................................................................................................4 2.1 CAUTIONS / WARNINGS .................................................................................4 2.2 DISCLAIMERS................................................................................................10 2.3 GP-SW1500TS KIT PARTS ............................................................................11 2.3.1 PARTS CHECKLIST .........................................................................11 2.4 GP-SW1500TS FEATURES ...........................................................................12 2.5 UNIT DIMENSIONS ........................................................................................14 2.6 POWER DE-RATING CURVE AND TRANSFER TIME ..................................15 3. INSTALLATION .................................................................................................................16 3.1 TYPICAL SYSTEM OVERVIEW .................................................................... 16 3.2 MOUNTING REQUIREMENTS ..................................................................... 20 3.3 DC WIRING ................................................................................................... 22 3.3.1 DC WIRING SIZING .........................................................................23 3.3.2 DC OVERCURRENT PROTECTION ...............................................24 3.3.3 PREPARING THE DC CABLES .......................................................24 3.3.4 DC CABLE CONNECTIONS ............................................................24 3.3.5 WIRING THE INVERTER TO THE BATTERIES ..............................25 3.3.6 DC GROUNDING .............................................................................25 3.4 AC WIRING.................................................................................................... 26 3.4.1 GP-SW1500TS AC WIRING TABLE .................................................26 3.4.2 HARD-WIRE INSTALLATION ...........................................................27 3.4.3 AC OUTPUT AND TERMINALS OF THE GP-SW1500TS ...............29 3.4.4 GFCI (GROUND FAULT CIRCUIT INTERRUPTION) OUTLETS .....29 4. OPERATION ......................................................................................................................30 4.1 FINAL INSPECTION .......................................................................................30 4.2 TESTING THE INSTALLATION ......................................................................30 4.3 CONNECTING THE AC LOADS .....................................................................30 4.4 LED INDICATOR ............................................................................................31 4.5 DIP SWITCH (S1~S8) ....................................................................................32 4.5.1 POWER SAVING MODE ..................................................................33 4.6 REMOTE PORT ..............................................................................................34 4.6.1 REMOTE CONTROL GREEN TERMINAL .......................................35 4.7 TROUBLESHOOTING ....................................................................................36 5. WARRANTY RETURN PROCEDURE ..............................................................................37 6. SPECIFICATIONS .............................................................................................................38 7. PRODUCT END OF LIFE - RECYCLING .........................................................................39 [page 4] | gpelectric.com 2.1 CAUTIONS / WARNINGS This document contains important safety instructions for the products produced by Go Power!. Read all instructions and cautionary markings on the product and on any accessories or additional equipment included in the installation. Failure to follow these instructions could result in severe shock or possible electrocution. Use extreme caution at all times to prevent accidents. All electrical work must be performed in accordance with local and national electrical codes. These instructions are for use by qualified personnel who meet all local and governmental code requirements for licensing and training for the installation of electrical power systems with AC and DC voltage up to 600 volts. Installation, maintenance, and connection of inverters must be performed by qualified personnel, in compliance with local electrical standards, wiring rules, and the requirements of local power authorities and/or companies. Safety regulations relevant to the location shall be followed during installation, operation and maintenance. Improper operation may have a risk of electric shock or damage to equipment and property. 2. GENERAL INFORMATION