Vicair Adjuster Manuals

All you need to know ADJUSTER relief by air 0800 238 523 www.mortonperry.co.nz [email protected] View the video VICAIR TECHNOLOGY The best medium for pressure redistribution is air. Unfortunately, there are a few drawbacks; air is unstable and it tends to leak. Vicair solved these issues when they created Vicair SmartCells. The unique Vicair air-technology, which uses the small air-filled SmartCells, was developed in cooperation with the Amsterdam Rehabilitation Centre. It was awarded the Grand Prix at the ‘Salon des Inventions’ in Geneva, Switzerland. Vicair develops and produces its product line in the Netherlands for customers all over the world. Unique combination of skin protection and positioning When you sit on a Vicair wheelchair cushion, you are supported by hundreds of SmartCells. The layers of cells inside the cushion compartments move with so little friction that the effect resembles the behaviour of a viscous fluid, slowly adjusting to the shape of your body. Also, because SmartCells deform individually, they conform to your body’s contours. The result is superior pressure redistribution. On top of this, the tetraeder-shape of the cells and the design of the cushion compartments make the Vicair cushion ultra stable and prevent the person sitting on it from sliding forward. As a result the cushion reduces shear forces to a bare minimum and helps to create and maintain an optimal, functional posture. Ease of use Vicair SmartCell cushions are extremely user-friendly. The well balanced filling grade ensures that Vicair cushions are ready to use, but if you prefer, you can adjust the cushions to your personal positioning needs by adding or removing SmartCells. The cushion requires hardly any maintenance; there is no need for a pump or any other accessories and once the cushion is set up, it doesn’t require daily monitoring. Not only are the Vicair wheelchair cushions extremely comfortable, but they are incredibly lightweight: on average weighing less than 0,8 kg each. This makes them the lightest high performance wheelchair cushions available by far. The Vicair cushion is always ready for use. Safe, durable and low on maintenance. View the technology Scan the code on your smartphone Min. 15 kg Max. 250 kg Min. -20°C Max. 55°C + 2.400 m - 50 m Min. 0% Max. 100% Quick Installation Guide 1 X Y=Y X=X X Y Y 2 3 4 5 6 7 5 min. Min. 2,5 cm Bruynvisweg 5 1531 AX Wormer Netherlands [email protected] vicair.com 070103-REV06/2016 2 cm 8 15 min. 8 717261 040660

Academy cushions NL Gebruiksaanwijzing GB User manual S Bruksanvisning N Brukermanual DK Brugermanual F Mode d’emploi I Istruzioni d’uso J E Instrucciones de uso D Gebrauchsanweisung SF Käyttöohje CN 使用說明書 all-guides.c om B A SIZE* cm inch Available models and sizes VECTOR TWIN POSITIONER + ADJUSTER 35x40 14x16 + + + 40x40 16x16 + + + + 40x45 16x1� + + + + 40x50 16x20 + + + 43x43 17x17 + + + + 45x40 1�x16 + + + + 45x45 1�x1� + + + + 45x50 1�x20 + + + 50x45 20x1� + + + 50x50 20x20 + + + * Width x Depth - The Twin, Postitioner + and Adjuster are available in 6 cm �2,5��� and 10 cm �4��� height� 6 cm �2,5��� and 10 cm �4��� height� - Specials and custom made products on request� Introduction Assembly ENGLISH Thank you for choosing a Vicair® Academy cushion� We are sure you will appreciate the simplicity, reliability and fantastic effect� Your Vicair®Academy cushion is designed to be used as described in this manual� Please read the whole manual before use� The cushion consists of the following parts: Inner cover The inner cover is made up of zippered compartments� The number and shape of the compartments depends on the cushion model� Each compartment is filled with a specific number of triangular, air filled SmartCells™� Outer cover Two types of outer cover are available: • Comfair, made of breathable fabric • Incontinence, made of waterproof incontinence-resistant material Both cover types have an anti-slip bottom surface and a two-way stretchable top surface� As the bottom of the cover is also provided with strips of Velcro tape, it is possible to fixate the cushion onto the wheelchair seat� Checking the cushion size Together with your therapist or dealer, make sure the cushion fits the dimensions of your body and your wheelchair� Width: The cushion should match the width of the wheelchair seat� If your wheelchair has armrests or side-guards that are capable of containing the cushion, the cushion may be up to 2 cm �0����� wider� Make sure the cushion cannot interfere with the wheel spokes� Depth: The cushion should match the length of the wheelchair seat, or be up to 2�5 cm �1��� longer� If the cushion is longer than that, we recommend the insertion of a solid seat base underneath the inner cushion, inside the outer cover� Fitting the cushion in the outer cover • Check if the dimensions of the outer cover matches the dimension of the cushion� • Remove the clear plastic wrapping� • Fully open the zipper in the outer cover� • Insert the inner cushion in the outer cover� • Pass the loop through the eyelet in the bottom panel of the outer cover �fig� A��� • Close the zipper in the outer cover� Make sure not to damage the inner cover� • Always use the cushion with the outer cover in place� Installation Use ENGLISH Vicair recommends to install and adjust the Academy cushions under the direct supervision of your therapist or dealer� • Make sure that the wheelchair seat is clean and degreased� • Remove the protective backing tape from the self-adhesive Velcro strips� • Place the cushion on the seat of your wheelchair and push it down firmly� Make sure the loop faces down and to the back of your wheelchair �fig� B��� To remove the cushion from the wheelchair seat, simply pull it off the Velcro strips� • Sit on the cushion for a few minutes, to allow the cushion to adapt to your body shape� • If necessary, adjust the footrests of your wheelchair� Your feet should just rest on them while your thighs are in full contact with the cushion� When you prefer not to use the Velcro, you can simply remove the self-adhesive Velcro strips� Note that the strips confected to the bottom of the cover cannot be removed� Adjusting the cushion filling Each Vicair® cushion has its own unique filling grade depending on size and model� Vicair® cushion has its own unique filling grade depending on size and model� cushion has its own unique filling grade depending on size and model� If necessary, the filling grade of the cushion can be adjusted by removing or adding SmartCells™ from the various compartments of the cushion� from the various compartments of the cushion� You can find the default filling grade on the label that is attached to the inner cover� Checking for “bottoming out” Your tailbone and pelvic bones should not touch the bottom of the cushion� Checking for “bottoming out� should be done during first use and after adjustments to the cushion filling� • Check the cushion for bottoming out, after sitting on the cushion for approximately 5 minutes� • Let your therapist or dealer slide a hand between the cushion and the wheelchair while leaning forward� • Make sure the buttocks are supported by at least ca�3cm / 1,2� of SmartCells™� • Do not use the cushion if bottoming out occurs� In most cases, adjusting the filling grade of the compartments, or using a different model or size of cushion will solve the problem� Checking for redness of the skin Check your skin regularly for redness, especially during the first few days� If redness occurs and does not disappear after 15 minutes, do not continue to use the cushion� Consult your therapist or dealer� Userweight The maximum userweight is 250kg �551 Lbs��

VICAIR-HANDBOOK REV0513 sales fax 800.564.9248 406.522.8563 comfortcompany.com Comfort Company 509 South 22nd Avenue Bozeman, MT 59718 VICAIR USER GUIDELINES ADJUSTER Front Rear A B D E C CELLS REMOVED CELLS ADDED A A B B C C D D E E VECTOR Front Rear A D CELLS REMOVED CELLS ADDED A A B B C C D D E E F F G G H H B C H G E F VICAIR ® ADJUSTMENT WORKSHEET DATE PATIENT NAME HEIGHT WEIGHT DIAGNOSIS *Proper positioning on cushion. *Improper cushion adjustments. Each compartment of the Adjuster Seat Cushion and the Vector Seat Cushion comes with a standard number of cells to accom- modate most user’s needs. Each compartment is designed to be adjustable by adding or removing cells to accommodate specific postural and pressure equalization requirements. To open the cushion and access the compartments, there are zippers located on the side edges of the cushion. NOTE: It is recommended that you consult your health care professional before making any significant adjustments to your cushion. NOTE: Bottoming Out: It is essential to ensure that your tailbone and pelvic bones are supported by at least two continuous layers of cells. Check for bottoming out during first time use and after adjustments to the number of cells in each chamber have been made. ADJUSTING THE CUSHION FILLING • • • You can easily check your cushion for the presence of sufficient cells under your pelvic bones. Start by sitting on the cushion and allowing the cushion to adjust to your shape. Wait 15 minutes for cells to adapt to your body’s contours. You can then perform a pressure relief and either use your hand or have someone check to verify that there are two continuous layers of cells under the bony pressure points. This test should be done only after full im- mersion in the cushion. Check your skin regularly for redness. If redness occurs and does not disappear within 15 minutes, it may indicate a problem. In the event of bottoming out or persistent redness of the skin, you must discontinue use of the cushion. Consult your health care professional immediately. CHECKING FOR IMPROPER ADJUSTMENTS • Congratulations on the purchase of your Vicair cushion. Your cushion is ready for use AS IS. Vicair cushions are developed to provide superior pressure relief and positioning directly out of the box. Although this is true, Vicair cushions can be customized by adding or removing comfort cells when needed. VICAIR ® USER GUIDELINES