Videofied DCV200 Manuals

Product Summary The Camera Model DCV200/DCV700/DCV600 is a wireless, indoor motion activated camera designed for use in VIDEOFIEDTM security systems. The camera includes the following features: > Lithium batteries for long life. > Wide angle lens. > Infrared LED for night illumination. > Standard motion coverage lens (12 m/40 ft. distance). > Dual tamper function provides detection for both wall and cover tamper. > Transmits check-in/status signal every 8 minutes. Installation Guidelines For easier installation, programming and RF testing should be done to check for good communication between the control panel and all system devices before mounting system devices. Install the detector and other system devices in the following order: > Programming/RF Testing - program detector and all other devices into the control panel and test RF communication from each intended device location to the control panel. > Mounting - mount detector at the tested location. Programming/RF Testing The following provides summarized steps for device programming and testing. For complete details, refer to the control panel installation manual. 1 Loosen bottom screw, separate base from camera and install batteries. 2 Re-attach base to secure tamper switch. 3 Put control panel into programming/configuration mode. 4 Using a programmed alphanumeric keypad, proceed through menus until the display shows ADD A NEW DEVICE. 5 Press YES. The display shows PRESS PROGRAM BUTTON OF DEVICE. 6 Press and release program button on camera using a paper clip end. The camera LED flashes. Wait for keypad display to show CAMERA (1 - 24) PROGRAMMED. 7 Press YES. The display shows RADIO RANGE TEST? Press YES again. The camera LED starts flashing and keypad display shows TEST IN PROGRESS. 8 Take camera to its intended mounting location and make sure LED flashes continuously, indicating good communication with control panel. 9 Press YES to end radio range test, then press ESC/NO. 10 The display shows AREA ASSIGNMENT AREA: Press either arrow button repeatedly until desired AREA number appears, then press Yes. 11 The display shows NAME + LOCATION. Enter appropriate device name/location (up to 16 characters), then press YES. The display shows the device number and name for your verification. 12 Press YES. The display shows FUNCTIONAL DEVICE TEST? Press YES again and verify camera operation. For example, wave your hand in front of the camera to activate its LED indicating detection. (walk test LED) 13 Press YES to end detection verification. 14 The display shows ADD A NEW DEVICE? Repeat steps 1 – 14 for remaining cameras. 15 When finished, exit from configuration mode. www.videofied.com Program Button Screw I N S T A L L A T I O N I N S T R U C T I O N S Camera Model DCV200/DCV600/DCV700 Made by RSI VIDEO TECHNOLOGIES 1002-c July 2008 Regulatory Information FCC Part 15 This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: 1.) This device may not cause harmful interference and, 2.) This device must accept any interference that may be received, including interference that may cause undesired operation. Changes or modifications not expressly approved by RSI VIDEO TECHNOLOGIES can void the user’s authority to operate the equipment Mounting > Use proper tools and hardware. > Mount indoors in a temperature-controlled environment. > Mount camera 2.1 to 2.3 m (6.9 to 7.5 ft.) from the floor. > Mount detector on an outside wall, aimed at area to be secured. > Do not aim detector at windows, especially those that let in direct sunlight, or at heat sources such as lamps, fireplaces, radiators, and heating vents. > Do not aim detector at moving objects such as curtains, fans. Specifications Panel Compatibility VIDEOFIED VISIO1000/V6000/V7000 Operating Frequency 868/915/920 MHz Radio type Spread Spectrum Bidirectional RF Power Requirements Three 3.6 V lithium batteries Battery Type LS14500 Motion detection Lens: Fresnel Detection distance: 12 m/ 40 ft. Angle: 90° Detector type: Dual elements Weight threshold: 18 kg/40 lbs. Camera sensor CMOS black & white Video resolution 320 x 240 pixels Video sequence (in alarm) 5 frames/s for 10 seconds Video sensitivity 0.2 lux Lens Wide-angle 85° (no IR treatment) Night illumination type Infrared (LED) Night illumination distance 4.5 m/14 ft. Operating Temperature 0°/+40°C (32°/104°F) Maximum Relative Humidity 70%, non-condensing Dimensions 89 mm x 70 mm x 70 mm (LxWxD): 3-1/2 in. x 2-3/4 in. x 2-3/4 in. Weight 150 g/5.3 oz. (without batteries) Approvals CE / EN50131 / EN300220 / INCERT/ IDA / NCP (DCV200) UL / FCC (DCV600) A-Tick (DCV700) 1 Separate base from camera. 2 Hold camera base against mounting surface and mark the two appropriate mounting holes. 3 Drill pilot holes and install anchors where needed. 4 Place base on mounting surface so mounting holes line up with pilot holes/anchors and secure base with appropriate screws. 5 Install batteries into camera, observing correct polarity. 6 Attach camera to base and secure with screw. EMEA SALES 2, rue Alexis de Tocqueville 92160 ANTONY FRANCE Phone +33 (0)1 55 59 10 25 Fax +33 (0)3 90 20 66 36 © 2008 RSI VIDEO TECHNOLOGIES. VIDEOFIEDTM is a Registered Trademark of RSI VIDEO TECHNOLOGIES. S2View® is a registered trademark of RSI VIDEO TECHNOLOGIES. Specifications subject to change without notice. USA SALES 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 USA Phone 877-206-5800 Fax 651-762-4693 www.videofied.com Flat Wall Mounting Holes Corner Mounting Holes I N S T A L L A T I O N I N S T R U C T I O N S Camera Model DCV200/DCV600/DCV700