Viking Range CVDD5300 Manuals

USE / INSTALLATION GUIDE 5 Series Rear Downdraft Ventilators 2 MODEL WIDTH BLOWER (purchased separately) VDD5300/CVDD5300 30" W. VDVI600 Interior or VDVE900 Exterior VDD5360/CVDD5360 36" W. VDVI600 Interior or VDVE900 Exterior VDD5450/CVDD5450 45" W. VDVI600 Interior or VDVE900 Exterior, VDVE1200 Exterior VDD5480/CVDD5480 48" W. VDVI600 Interior or VDVE900 Exterior, VDVE1200 Exterior WARNING READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number in the warranty. 2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. 3. Installation work and electrical wiring must be done by a qualifi ed person(s) in accordance with all applicable codes and standards, including fi re-rated construction codes and standards. 4. Suffi cient air is needed for proper combustion and exhausting of gases through the fl ue (chimney) of fuel burning equip- ment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authori- ties. 5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. 6. Ducted fans must always be vented to the outdoors. 7. To reduce the risk of fi re, use only metal ductwork. 8. Do not install this product with the activating switch directly behind a burner or element. Minimum distance between the switch and the edge of the burner should be 4 inches. 9. Loose-fi tting or hanging clothing should never be worn when operating this appliance. They may be ignited by burners/ elements on cooktop. 10. Children should not be left alone or unattended in the area where this appliance is in use. 11. This unit must be grounded. TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. b) Always turn hood ON when cooking at high heat or when cooking fl aming foods. c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or fi lter. d) Use proper pan size. Always use cookware appropriate for the size of the surface element. TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWINGa: 1. SMOTHER FLAMES with a close-fi tting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the fl ames do not go out immedi- ately, EVACUATE AND CALL THE FIRE DEPARTMENT. 2. NEVER PICK UP A FLAMING PAN - You may be burned. 3. DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will result. 4. Use an extinguisher ONLY if: A. You know you have a Class ABC extinguisher, and you already know how to operate it. B. The fi re is small and contained in the area where it started. C. The fi re department is being called. D. You can fi ght the fi re with your back to an exit. a Based on “Kitchen Firesafety Tips” published by NFPA. CAUTION 1. For indoor use only. 2. For general ventilating use only. Do not use to exhaust haz- ardous or explosive materials and vapors. 3. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit. 4. Clean fi lters and grease-laden surfaces frequently. 5. Do not repair or replace any part of this appliance unless specifi cally recommended in this manual. All other servicing should be done by a qualifi ed technician. 6. Please read specifi cation label on product for further informa- tion and requirements. 7. To reduce the risk of fi re and electric shock, install this down- draft only with blower models shown below. Other blower models cannot be substituted. (Blowers sold separately). Flex Blower Model VDVI600 Exterior Blower Models VDVE900, VDVE1200 INSTALLER: Save this manual for Electrical Inspector and Homeowner to use. 3 PLANNING ELECTRICAL SPECIFICATIONS Model VDVI600 - Internal Flex: 120 VAC • 60 Hz • 3.0 A Models VDVE900, VDVE1200 - Exterior 120 VAC • 60 Hz • 6.0 A (max.) TAKE MEASUREMENTS Due to its fl exible design, this downdraft system can be used to ex- haust airborne contaminants when cooking with a variety of gas or electric cooking appliances - including cooktops, rangetops, slide-in ranges and free-standing ranges. It can be mounted in island, peninsula, or conventional wall loca- tion. The blower (purchase separately) and electrical panel can be mounted to the downdraft unit, inside the cabinet, or in a convenient remote location. This unit can be easily installed following these basic steps: • Cut out the countertop opening. • Mount the unit in the cabinet. • Install the blower and electrical panel. • Connect the ductwork and electrical. • Mount the trim/door. • Install the cooking appliance. Note: the high level of air fl ow of this appliance may effect the gas fl ame on some types of gas cooktops. This is NORMAL and will cause no harm, but can be corrected by lowering the speed of the blower. PLAN THE DUCTWORK 1. Refer to the cooktop installation instructions for dimensions of cooktop, countertop cut-out, and cabinet requirements. However, it is recommended that oversized cabinets be used for easier installation. 2. Cooktop depth can vary greatly from one to another. This may cause the fi t of these two appliances to be rather tight. Pay special attention to the areas of potential interference highlighted above. A countertop with (A) a raised lip and/or (B) a backsplash may not allow enough fl at countertop for a proper installation. Note that 2-3/4" of fl at countertop is required behind cooktop and that 1-3/4" is necessary between the back edge of the cooktop and the inside of cabinet back. HOUSING 1. The downdraft blower system is designed for use with 8" round ductwork using a fl ex blower or 10" Round ductwork using a remote blower. (Purchase blowers separately.) Six (6) different discharge connections are available - with side-to-side adjustment for accurate alignment of ductwork: A = 8" Round, Left Discharge out of Flex Blower B = 8" Round, Right Discharge out of Flex Blower C = 8" Round, Down Discharge out of Flex Blower (Electrical Box to be mounted remotely) D = 2" x 19¼", Left Discharge out of Housing to Remote Blower or Flex Blower in remote location. Use 2" x 19¼" to 8" round transition, 2" x 19¼" to 10" round transition, or 2" x 19¼" ductwork as appropriate. E = 2" x 19¼", Right Discharge out of Housing to Remote Blower or Flex Blower in remote location. Use 2" x 19¼" to 8" round transition, 2" x 19¼" to 10" round transition, or 2" x 19¼" ductwork as appropriate. F = 2" x 19¼", Rear Discharge out of Housing to Remote Blower or Flex Blower in remote location. Use 2" x 19¼" to 8" round transition, 2" x 19¼" to 10" round transition, or 2" x 19¼" ductwork as appropriate. 2. For best performance: Choose the ducting option which allows the shortest length of ductwork and a minimum number of elbows and transitions. Check location of fl oor joists, wall studs, electrical wiring or plumbing for possible interference. CONTENTS These parts are included with your downdraft housing: 1 - Parts Bag 1 - Trim Kit 4 - Support Legs 1 - Electrical Panel 2 - Support Brackets 2-3/4" 2-1/2" FLEX BLOWER * * Remote blowers use 8" or 10" round remote discharge plate instead of fl ex blower.

Use/Installation GUIDE 5 SERIES Rear Downdraft Ventilators VDD5300/CVDD5300 VDD5360/CVDD5360 VDD5450/CVDD5450 VDD5480/CVDD5480 2 MODEL WIDTH BLOWER (purchased separately) VDD5300/CVDD5300 30" W. VDVI600 Interior or VDVE900 Exterior VDD5360/CVDD5360 36" W. VDVI600 Interior or VDVE900 Exterior VDD5450/CVDD5450 45" W. VDVI600 Interior or VDVE900 Exterior, VDVE1200 Exterior VDD5480/CVDD5480 48" W. VDVI600 Interior or VDVE900 Exterior, VDVE1200 Exterior WARNING READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number in the warranty. 2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. 3. Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards. 4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities. 5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. 6. Ducted fans must always be vented to the outdoors. 7. To reduce the risk of fire, use only metal ductwork. 8. Do not install this product with the activating switch directly behind a burner or element. Minimum distance between the switch and the edge of the burner should be 4 inches. 9. Loose-fitting or hanging clothing should never be worn when operating this appliance. They may be ignited by burners/ elements on cooktop. 10. Children should not be left alone or unattended in the area where this appliance is in use. 11. This unit must be grounded. 12. To reduce the risk of fire or electric shock, it is recommended that the downdraft be installed with a dedicated circuit separate from the appliance. TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. b) Always turn hood ON when cooking at high heat or when cooking flaming foods. c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter. d) Use proper pan size. Always use cookware appropriate for the size of the surface element. TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*: 1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immedi- ately, EVACUATE AND CALL THE FIRE DEPARTMENT. 2. NEVER PICK UP A FLAMING PAN - You may be burned. 3. DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will result. 4. Use an extinguisher ONLY if: A. You know you have a Class ABC extinguisher, and you already know how to operate it. B. The fire is small and contained in the area where it started. C. The fire department is being called. D. You can fight the fire with your back to an exit. * Based on “Kitchen Firesafety Tips” published by NFPA. CAUTION 1. TO REDUCE THE RISK OF FIRE OR INJURY, DO NOT INSTALL WITH COOKING PRODUCTS THAT HAVE A GRIDDLE. 2. For indoor use only. 3. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. 4. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit. 5. Clean filters and grease-laden surfaces frequently. 6. Do not repair or replace any part of this appliance unless specifically recommended in this manual. All other servicing should be done by a qualified technician. 7. Please read specification label on product for further information and requirements. 8. To reduce the risk of fire and electric shock, install this downdraft only with blower models shown below. Other blower models cannot be substituted. (Blowers sold separately). Flex Blower Model VDVI600 Exterior Blower Models VDVE900, VDVE1200 INSTALLER: Save this manual for Electrical Inspector and Homeowner to use. 3 PLANNING ELECTRICAL SPECIFICATIONS Model VDVI600 - Internal Flex: 120 VAC • 60 Hz • 3.0 A Models VDVE900, VDVE1200 - Exterior 120 VAC • 60 Hz • 6.0 A (max.) TAKE MEASUREMENTS DO NOT INSTALL WITH COOKING PRODUCTS THAT HAVE A GRIDDLE. Due to its flexible design, this downdraft system can be used to exhaust airborne contaminants when cooking with a variety of gas or electric cooking appliances - including cooktops, rangetops, slide-in ranges and free-standing ranges. It can be mounted in island, peninsula, or conventional wall location. The blower (purchase separately) and electrical panel can be mounted to the downdraft unit, inside the cabinet, or in a convenient remote location. This unit can be easily installed following these basic steps: • Cut out the countertop opening. • Mount the unit in the cabinet. • Install the blower and electrical panel. • Connect the ductwork and electrical. • Mount the trim/door. • Install the cooking appliance. Note: the high level of air flow of this appliance may effect the gas flame on some types of gas cooktops. This is NORMAL and will cause no harm, but can be corrected by lowering the speed of the blower. PLAN THE DUCTWORK 1. Refer to the cooktop installation instructions for dimensions of cooktop, countertop cut-out, and cabinet requirements. However, it is recommended that oversized cabinets be used for easier installation. 2. Cooktop depth can vary greatly from one to another. This may cause the fit of these two appliances to be rather tight. Pay special attention to the areas of potential interference highlighted below. A countertop with (A) a raised lip and/or (B) a backsplash may not allow enough flat countertop for a proper installation. Note that 2-3/4" of flat countertop is required behind cooktop and that 2-1/2" is necessary between the back edge of the cooktop and the inside of cabinet back. A B C D E F HOUSING 1. The downdraft blower system is designed for use with 8" round ductwork using a flex blower or 10" Round ductwork using a remote blower. (Purchase blowers separately.) Six (6) different discharge connections are available - with side-to-side adjustment for accurate alignment of ductwork: A = 8" Round, Left Discharge out of Flex Blower B = 8" Round, Right Discharge out of Flex Blower C = 8" Round, Down Discharge out of Flex Blower (Electrical Box to be mounted remotely) D = 2" x 19¼", Left Discharge out of Housing to Remote Blower or Flex Blower in remote location. Use 2" x 19¼" to 8" round transition, 2" x 19¼" to 10" round transition, or 2" x 19¼" ductwork as appropriate. E = 2" x 19¼", Right Discharge out of Housing to Remote Blower or Flex Blower in remote location. Use 2" x 19¼" to 8" round transition, 2" x 19¼" to 10" round transition, or 2" x 19¼" ductwork as appropriate. F = 2" x 19¼", Rear Discharge out of Housing to Remote Blower or Flex Blower in remote location. Use 2" x 19¼" to 8" round transition, 2" x 19¼" to 10" round transition, or 2" x 19¼" ductwork as appropriate. 2. For best performance: Choose the ducting option which allows the shortest length of ductwork and a minimum number of elbows and transitions. Check location of floor joists, wall studs, electrical wiring or plumbing for possible interference. CONTENTS These parts are included with your downdraft housing: 1 - Parts Bag 4 - Support Legs 1 - Trim Kit 1 - Electrical Panel 2 - Support Brackets 2-3/4" 2-1/2" FLEX BLOWER * * Remote blowers use 8" or 10" round remote discharge plate instead of flex blower. Note: Remove all protective film and packaging before op- eration. In order to remove all protective film and packag- ing, raise the ventilator housing and remove the front panel to access the filter area. 4 PLAN THE WIRING 1. This downdraft blower using the Flex Blower (purchase separately) draws 3.0 Amps and requires a 120 VAC, 60 Hz circuit. If using a remote blower (purchase separately), the system draws 6.0 Amps (max.) and requires a 120 VAC, 60 Hz circuit. 2. The unit has a 18 in. long power cord with a 3-pronged plug. Plan to provide a grounded outlet in a location which will allow the unit’s power cord to reach. 3. Install electrical box according to local codes. 4. The length of cable from the electrical box to the downdraft is 20 in. 5. The length of blower (sold separately) cable to the electrical box is 5 ft. PREPARE THE DOWNDRAFT Installations ducting through front panel opening only: 1. Place the downdraft on its back on a table or flat work surface. 2. Loosen the HEX NUTS on the CLAMP CHANNEL and remove the FRONT PANEL COVER. FRONT PANEL COVER CLAMP CHANNEL (4-6) HEX NUTS Installations using FLEX BLOWER only: (Purchase Model VDVI600 Flex Blower separately.) 3. Determine its location on FRONT PANEL and whether it will discharge to the left, right, or down. Use a combination of COVER PLATES (3" and/or 6" wide) to close the opening on side(s) of blower. Slide the blower and cover plates between the LOWER CHANNEL and the clamp channel. Tighten the hex nuts to secure blower and panels in place. LOWER CHANNEL COVER PLATE COVER PLATES (included with blower) FLEX BLOWER FRONT PANEL If blower discharge is down, electrical panel must be relocated. See Step 6. PLAN CABINET CUTOUTS CAUTION: BEFORE CUTTING HOLE IN CABINET FOR DUCTWORK, check for interference with floor joists, wall studs, electrical wiring, or plumbing. Use the dimensions in the above illustration to help plan how and where to provide duct access through your cabinet. Generally, 1-7/8" x 19" rectangular duct will be used through left, right, and back of cabinet - while 8" round duct will be used through cabinet floor. For left, right, or rear exhaust: Allow at least 18" for transition and elbow or blower. For left/right exhaust: A 30" deep cabinet is recommended to align properly with flex blower. Flex blower can be mounted to rear cabinet wall or to a platform/frame (not provided) on the base of the cabinet floor. (See flex blower instructions). Cabinet depths of 24" to 30" are required - depending on the type of cooking appliance. Electrical panel can be mounted remotely. INSTALLATION CENTER LINE HOLE FOR 8” or 10” ROUND DUCT (*Adjustable 6” Left and 6” Right) (When using Remote Discharge Plate - Hole is adjustable 6” Left and 6” Right from Installation Center Line.) HOLE FOR 2” X 19¼” DUCT INSIDE CABINET BACK INSIDE CABINET FLOOR 1½” 6”* 6”* 19¼” centered 2” 26¾” 6 ” 7/8 FLUSH 19¼” 2”

USE / INSTALLATION GUIDE 5 Series Rear Downdraft Ventilators 2 MODEL WIDTH BLOWER (purchased separately) VDD5300/CVDD5300 30" W. VDVI600 Interior or VDVE900 Exterior VDD5360/CVDD5360 36" W. VDVI600 Interior or VDVE900 Exterior VDD5450/CVDD5450 45" W. VDVI600 Interior or VDVE900 Exterior, VDVE1200 Exterior VDD5480/CVDD5480 48" W. VDVI600 Interior or VDVE900 Exterior, VDVE1200 Exterior WARNING READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number in the warranty. 2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. 3. Installation work and electrical wiring must be done by a qualifi ed person(s) in accordance with all applicable codes and standards, including fi re-rated construction codes and standards. 4. Suffi cient air is needed for proper combustion and exhausting of gases through the fl ue (chimney) of fuel burning equip- ment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authori- ties. 5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. 6. Ducted fans must always be vented to the outdoors. 7. To reduce the risk of fi re, use only metal ductwork. 8. Do not install this product with the activating switch directly behind a burner or element. Minimum distance between the switch and the edge of the burner should be 4 inches. 9. Loose-fi tting or hanging clothing should never be worn when operating this appliance. They may be ignited by burners/ elements on cooktop. 10. Children should not be left alone or unattended in the area where this appliance is in use. 11. This unit must be grounded. TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. b) Always turn hood ON when cooking at high heat or when cooking fl aming foods. c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or fi lter. d) Use proper pan size. Always use cookware appropriate for the size of the surface element. TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWINGa: 1. SMOTHER FLAMES with a close-fi tting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the fl ames do not go out immedi- ately, EVACUATE AND CALL THE FIRE DEPARTMENT. 2. NEVER PICK UP A FLAMING PAN - You may be burned. 3. DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will result. 4. Use an extinguisher ONLY if: A. You know you have a Class ABC extinguisher, and you already know how to operate it. B. The fi re is small and contained in the area where it started. C. The fi re department is being called. D. You can fi ght the fi re with your back to an exit. a Based on “Kitchen Firesafety Tips” published by NFPA. CAUTION 1. For indoor use only. 2. For general ventilating use only. Do not use to exhaust haz- ardous or explosive materials and vapors. 3. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit. 4. Clean fi lters and grease-laden surfaces frequently. 5. Do not repair or replace any part of this appliance unless specifi cally recommended in this manual. All other servicing should be done by a qualifi ed technician. 6. Please read specifi cation label on product for further informa- tion and requirements. 7. To reduce the risk of fi re and electric shock, install this down- draft only with blower models shown below. Other blower models cannot be substituted. (Blowers sold separately). Flex Blower Model VDVI600 Exterior Blower Models VDVE900, VDVE1200 ! INSTALLER: Save this manual for Electrical Inspector and Homeowner to use. 3 PLANNING ELECTRICAL SPECIFICATIONS Model VDVI600 - Internal Flex: 120 VAC • 60 Hz • 3.0 A Models VDVE900, VDVE1200 - Exterior 120 VAC • 60 Hz • 6.0 A (max.) TAKE MEASUREMENTS Due to its fl exible design, this downdraft system can be used to ex- haust airborne contaminants when cooking with a variety of gas or electric cooking appliances - including cooktops, rangetops, slide-in ranges and free-standing ranges. It can be mounted in island, peninsula, or conventional wall loca- tion. The blower (purchase separately) and electrical panel can be mounted to the downdraft unit, inside the cabinet, or in a convenient remote location. This unit can be easily installed following these basic steps: • Cut out the countertop opening. • Mount the unit in the cabinet. • Install the blower and electrical panel. • Connect the ductwork and electrical. • Mount the trim/door. • Install the cooking appliance. Note: the high level of air fl ow of this appliance may effect the gas fl ame on some types of gas cooktops. This is NORMAL and will cause no harm, but can be corrected by lowering the speed of the blower. PLAN THE DUCTWORK 1. Refer to the cooktop installation instructions for dimensions of cooktop, countertop cut-out, and cabinet requirements. However, it is recommended that oversized cabinets be used for easier installation. 2. Cooktop depth can vary greatly from one to another. This may cause the fi t of these two appliances to be rather tight. Pay special attention to the areas of potential interference highlighted below. A countertop with (A) a raised lip and/or (B) a backsplash may not allow enough fl at countertop for a proper installation. Note that 2-3/4" of fl at countertop is required behind cooktop and that 1-3/4" is necessary between the back edge of the cooktop and the inside of cabinet back. A B C D E F HOUSING 1. The downdraft blower system is designed for use with 8" round ductwork using a fl ex blower or 10" Round ductwork using a remote blower. (Purchase blowers separately.) Six (6) different discharge connections are available - with side-to-side adjustment for accurate alignment of ductwork: A = 8" Round, Left Discharge out of Flex Blower B = 8" Round, Right Discharge out of Flex Blower C = 8" Round, Down Discharge out of Flex Blower (Electrical Box to be mounted remotely) D = 2" x 19¼", Left Discharge out of Housing to Remote Blower or Flex Blower in remote location. Use 2" x 19¼" to 8" round transition, 2" x 19¼" to 10" round transition, or 2" x 19¼" ductwork as appropriate. E = 2" x 19¼", Right Discharge out of Housing to Remote Blower or Flex Blower in remote location. Use 2" x 19¼" to 8" round transition, 2" x 19¼" to 10" round transition, or 2" x 19¼" ductwork as appropriate. F = 2" x 19¼", Rear Discharge out of Housing to Remote Blower or Flex Blower in remote location. Use 2" x 19¼" to 8" round transition, 2" x 19¼" to 10" round transition, or 2" x 19¼" ductwork as appropriate. 2. For best performance: Choose the ducting option which allows the shortest length of ductwork and a minimum number of elbows and transitions. Check location of fl oor joists, wall studs, electrical wiring or plumbing for possible interference. CONTENTS These parts are included with your downdraft housing: 1 - Parts Bag 1 - Trim Kit 4 - Support Legs 1 - Electrical Panel 2 - Support Brackets 2-3/4" 2-1/2" FLEX BLOWER * * Remote blowers use 8" or 10" round remote discharge plate instead of fl ex blower.