Viking E-1600 Manuals

K-1600-EHF E-1600-03 E-1600-02 E-1600 Using the 1600 Series Phones with Central Station Equipment VIKING© Application Note Telecommunication Peripheral Products 1600 Series Central Station Monitoring August 1, 1997 Once the receiver has issued the proper acknowledgement tone, the “CALL CONNECTED” indicator on the front of the emergency phone will light, and the 1600 phone will then switch to two-way voice. Programming A. Programming Features http://www.VikingElectronics.com [email protected] Sales...(715) 386-8861 The standard 1600 emergency phone is factory programmed to communicate using the Ademco “Contact I.D.”, “Ademco High Speed”, “DTMF 4+1 Express”, or the “DTMF 4+2 Express” formats. All formats use the programming memory location #20 to store the account code and alarm details. Note: This document must be used in combination with the 1600 Series Technical Practice (Fax Back Document 215). The 1600 series of emergency telephones have the capability to communicate directly with central station receivers. In this mode, the emergency phone will automatically relay vital information to compatible equipment at central alarm monitoring stations. The 1600 series emergency phone can be placed in the “central station mode” by entering a ,1 while programming. To cancel the “central station mode,” enter ,0 (see 1600 Series Technical Practice, section F). 1. Accessing the programming mode 2. Enabling/Disabling Central Station Mode Before programming, you must access the programming mode (see 1600 Series Technical Practice, section A). 3. Ring Delay When the 1600 series emergency phone is in the central station mode, it is best to have the ring delay set to a minimum of three. Some receivers send a long tone after answering the line that sounds like a ring back, and if the 1600 is set to a ring delay of two, the phone will disconnect (see 1600 Series Technical Practice, section G, setting D). Primary and Secondary Speed Dial Numbers 4. The 1600 series phone can be programmed to dial a central station receiver only, or dial a voice number first, and if no answer, then dial the central station receiver. When calling the first number (memory position 00), the phone stays in “two-way talk mode” allowing two-way conversation. When calling the second number (memory position 01), the phone is in a “listen only mode” in order to interpret the hand shake signal of the receiver (see 1600 Series Technical Practice, sections C and D). Note: If only a central station is to be dialed, the central station phone number must be preprogrammed in memory location 01 and memory location 00 must be cleared. Memory Location 00 01 Two-Way Voice Central Station Mode

The 1600A Series ADA Compliant Emergency Phones are designed to provide quick and reliable handsfree communi- cation for any standard analog telephone line or analog phone system station port. All 1600A Series phones meet ADA requirements for elevator/ emer- gency telephones, and can be programmed from any Touch Tone phone. The phones can dial up to 5 programmable emergency numbers, as well as 2 central station numbers. In addi- tion, the E-1600-20A and E-1600-52A feature a second "INFO" button that will dial up to 3 non-emergency numbers. The 1600A Series phones can be pro- grammed to automatically deliver a digital announcement to identify the location of the emergency call. Alternatively, a DTMF Touch Tone code may also be delivered. A “Call Connected” LED can be initiated manually or automatically. All programming parameters, including phone numbers and loca- tion numbers, are stored in non-volatile E2 memory. All units are phone line powered, requiring no batteries or external power and are compatible with common Central Station Monitoring equipment. For outdoor installations where the unit is exposed to precipitation or condensation, select 1600A Series phones are available with Enhanced Weather Protection (EWP). EWP products feature foam rubber gaskets and boots, sealed connections, gel-filled butt connectors, as well as urethane or thermal plastic potted circuit boards with internally sealed, field-adjustable trim pots and DIP switches for easy on-site programming. For more information, see DOD# 859. 1600A Series 1600A Series ADA Compliant Emergency Phones August 20, 2012 ADA* Compliant Emergency Phones with Built-In Digital Voice Announcer • Meets the latest ASME A17.1 code when used with the optional LV-1K Line Verification Panel, see DOD# 246 • Meets ADA requirements for Emergency Phones: - Can automatically light the “Call Connected” LED for the hearing impaired - Transmits a unique location I.D. code or voice announcement - Grade 2 Braille label for the visually impaired • Non-volatile digital voice announcer with 16 seconds of voice memory • Advanced call progress detection • Handsfree operation • Phone line powered • Non-volatile memory (no batteries required) • Marine grade 316 stainless steel prevents corrosion on stainless models • Dials up to 5 emergency numbers • E-1600-20A and E-1600-52A dial up to 3 non-emergency “INFO” numbers • Cycles through backup emergency and non-emergency numbers on busy or no-answer • Optional Enhanced Weather Protection (EWP), EWP products are designed to meet IP66 Ingress Protection Rating, see DOD# 859 • Hangs up on CPC, silence, busy signal, dial tone, time-out or touch tone command • Programmable to auto-answer on incoming calls • Remotely programmable • Extended temperature range (-15°F to 130°F) • 9 different chassis or board only available • Available in 42” tall tower phone model E-1600A-BLT-EWP (DOD# 217) • Central Station Monitoring capability (dials 2 numbers) • Optional PB-100 Polling System available (DOD# 232) • Optional BLK-3-EWP strobe light kit available (DOD# 653) • Optional LC-6 Six Port Concentrator available (DOD# 245) • Optional LV-1K Line Verification Panel available (DOD# 246) PPrraaccttiiccee TTEELLEECCO OM M SSO OLLUUTTIIO ONNSS FFO ORR TTHHEE 2211SSTT CCEENNTTUURRYY TECHNICAL TECHNICAL FFeeaattuurreess E-1600-45A K-1600-EHFA E-1600A E-1600-02A E-1600-03B E-1600-20A Power: Telephone line powered. Minimum 24V DC talk battery voltage, with a minimum loop current of 20mA loop. Loop current may be boosted on low current lines with a Viking Model TBB-1B talk battery booster, see DOD# 632. Dimensions: See Installation and Specifications Operating Temperature: -26° C to 54° C (-15° F to 130° F) Humidity - Standard Products: 5% to 95% non-condensing Humidity - EWP Products: Up to 100% SSppeecciiffiiccaattiioonnss * Americans with Disabilities Act of 1992 contains federal reg- ulations regarding elevator telephones (Public Law 101-336). • Elevators • Parking ramps/lots • ATM machines • Area of refuge locations • Lobbies • Entryways • Campus emergency stations • Roadside emergency stations • Stadiums • Convention centers AApppplliiccaattiioonnss CAUTION - When installing on an analog extension of a phone system: Some phone systems do not conform to analog telecom standards and might not be compatible with the 1600A Series emergency phones. For a detailed description of the telephone line specifications required for any of the 1600A Series phones, see DOD# 869. E-1600-55A E-1600-30A E-1600-60A

VE-LIGHT VE-LIGHT Enclosure Lighting Kit November 17, 2008 PPhhoonnee......771155..338866..88886611 iinnffoo@ @vviikkiinnggeelleeccttrroonniiccss..ccoom m hhttttpp::////wwwwww..vviikkiinnggeelleeccttrroonniiccss..ccoom m Power: 120V AC/12V DC 500mA, UL listed adapter provided or use any 12-24V AC or DC source @ 50mA Dimensions: 127mm x 8mm x 25mm (5” x 3” x 1”) Environmental: -26°C to 54°C (-15°F to 130°F) with 5% to 95% non-condensing humidity Shipping Weights: 0.45 kg (1 lb) Maximum Power Run: 304m (1000 ft) using 24 AWG wire Add Panel Lighting to Your Viking Doorbox or Entry Phone The VE-LIGHT kit adds bright LED illumination to any doorbox or entry phone that is housed in a Viking VE- 5x5, VE-6x7 or VE-5x10 enclosure. It can also be used on Viking’s E-1600A-BLT-EWP tower phone. The stainless steel bracket is easily mounted using existing holes and hardware. Two bright white LEDs are used as the light source, so there are no filaments to break or bulbs to burn out. If used with the W-1000, W-3000 or W-3005, the VE- LIGHT can be wired directly to the AC power input of the doorbox, or use the included 12 volt power sup- ply. Any power source between 12 and 24 volts, AC or DC can be used to supply the VE-LIGHT with power. PPrraaccttiiccee TTEELLEECCO OM M SSO OLLUUTTIIO ONNSS FFO ORR TTHHEE 2211SSTT CCEENNTTUURRYY TECHNICAL TECHNICAL SSppeecciiffiiccaattiioonnss FFeeaattuurreess • Ultra bright LEDs for long life • Easy retro-fit to existing entry phones • Can use the same power source as doorbox • Can be powered from 12 to 24 volts AC or DC AApppplliiccaattiioonnss VE-LIGHT shown above with Viking W-3000 and VE-5x5 (not included) • The VE-LIGHT is designed to be used in conjunction with the following products: Model E-10A/EWP E-30/EWP E-30-PT/EWP E-35/EWP E-1600-20A/EWP E-1600-30A/EWP E-1600A-BLT-EWP E-1600A-BLT2-EWP K-1500-7 K-1700-3/EWP K-1705-3/EWP K-1900-7/EWP K-1900-8/EWP W-1000/EWP W-3000/EWP W-3005 DOD# 210 212 214 178 215 215 217 217 352 157 159 364 362 170 180 181 VE Model VE-5x5 / SS VE-5x5 / SS VE-5x5 / SS VE-5x5 / SS VE-5x5 / SS VE-5x5 / SS (included) (included) VE-5x10 / SS VE-6x7 / SS VE-6x7 / SS VE-5x10 / SS VE-5x10 / SS VE-5x5 / SS VE-5x5 / SS VE-5x5 / SS