Vision Fitness T9800 Series Manuals

PARTS BOX Water Bottle, Qty: 1 Handlebars, Qty: 2 Handlebar Covers, Qty: 2 Power Cord, Qty: 1 Color-coded Hardware Bags PINK BAG Quantity: 8 Quantity: 4 Quantity: 4 M8 x 15L Flat Head Quantity: 2 6.5x19x2T Flat Washer Quantity: 4 6.5x13x1T Arc Washer Quantity: 2 M6 x 15L Socket Head Quantity: 6 M5 x 12L Phillips Head Quantity: 2 HARDWARE INCLUDED Screwdriver TOOLS, HARDWARE, & PARTS INCLUDED PARTS BOX Water Bottle, Qty: 1 Handlebars, Qty: 2 Handlebar Covers, Qty: 2 Power Cord, Qty: 1 Color-coded Hardware Bags ORANGE BAG BLUE BAG M10 x 20L Bolt Quantity: 4 PINK BAG M8 x 15L Socket Head Quantity: 8 5mm L-Shaped Wrench 5 STEP DO NOT STAND ON THE BELT WHEN PERFORMING AUTO-CALIBRATION You need to access User Engineering Mode to run the auto-calibration. With the safety key in place, please hold down SPEED DOWN and ENTER for 5 seconds. When in the User mode, “USER ENG MODE” appears in the alphanumeric window. To access the data press the ELEVATION keys until “AUTO-CALIBRATION” appears. To begin auto-calibration, press ENTER. The treadmill will run through minimum and maximum speed and maximum incline. This will take 3-5 minutes. Let the treadmill perform this complete function before exiting the Engineering Mode. Elevation A/D appears in the left window. PWM value appears in the dot matrix window, and speed appears in the right window. “CALIBRATION PASSED” will appear in the alphanumeric window when the auto-calibration is complete. The treadmill will come to a complete stop and return to the start-up screen in the alphanumeric window. AUTO-CALIBRATION 8.2x19x2T Flat Washer Quantity: 8 10.2x19x2T Flat Washer Quantity: 4 M8 x 15L Socket Head Quantity: 4 8.2x19x2T Flat Washer Quantity: 4 M8 x 15L Flat Head Quantity: 2 6.5x19x2T Flat Washer Quantity: 4 6.5x13x1T Arc Washer Quantity: 2 M6 x 15L Socket Head Quantity: 6 6mm L-Shaped Wrench 8mm T-Shaped Wrench M5 x 12L Phillips Head Quantity: 2 A s s e m b l y G u i d e To avoid possible damage to this Platform Treadmill, please follow these assembly steps in the correct order. Before proceeding though, find your new Platform Treadmill’s 2 serial numbers, located on the underside of the main frame, and on the bottom of the console, and enter here: Refer to these numbers when calling for service, and also enter these serial numbers on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Platform Treadmill. If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12 NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Platform Treadmill, to prevent loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt. 1 STEP • Remove motor cover screws and take off the motor cover. • Insert the right console mast to the right console mast bracket. First, fasten the inside of the console mast to the console mast bracket by securing four bolts (M8x15L socket head) and four washers (8.2x19x2T). Fully tighten the bolts. Second, fasten the two bolts (M10x20L button head) and two washers (10.2x19x2T) on the front of the console mast and fully tighten. • Repeat on the left side ORANGE BAG 1 STEP 2 STEP 3 STEP • Insert the handlebar cover onto the handlebar. Insert the right handlebar by holding the handlebar sideways toward the treadmill and inserting the top into the console. Rotate the handlebar into the bracket located on the console mast. Fasten with a bolt (M5x12L), and a bolt (M6x15L socket head) & an arc washer (6.5x13x1T) into the two holes of the console plas- tic, and a bolt (M8x15L flat head) into the hole in the handlebar. Fasten a bolt (M6x15L socket head) and a flat washer (6.5x19x2T) into the hole in the handle- bar on the console mast. Do not fully tighten the bolts. • Slide the handlebar cover over the bracket and secure with a bolt (M6x15L socket head) and a flat washer (6.5x19x2T). Do not fully tighten the bolt. • Repeat on the left side. • Fully tighten the console and handlebar bolts. PINK BAG 6 STEP T9800 Series TREADMILLS 6 STEP • If the running belt slips when used, run the treadmill at 2.0 mph and use the supplied 8mm Allen wrench to turn the left and right tension bolts clockwise 1/4-turn at a time until the belt no longer slips. • If the running belt is too far to the right side, run the treadmill at 2.0 mph and use the supplied 8mm Allen wrench to turn the right tension bolt clockwise 1/4-turn at a time until the belt remains centered during use. If the running belt is too far to the left side, run the treadmill at 2.0 mph and turn the left tension bolt clockwise 1/4-turn at a time until the belt remains centered during use. BELT TENSION 4 STEP • Place the motor cover back on the frame and fasten with 6 screws. • Attach the power cord to the treadmill. • Plug the power cord into the power outlet. MOTOR COVER 3 STEP Frame Serial Number Console Serial Number 2 STEP • Tie the ribbon data cable, TV power cable, and coaxial cable to the cable wire tie on the top of the right console mast. Feed the cables down the console mast and through the hole at the lower part of the console mast. Remove protective plastic cover. Push any remaining cable into the console mast. • Mount the console onto the left and right console masts using four bolts (M8x15L socket head) and four washers (8.2x19x2T). Do not fully tighten. • Take the wire tie off the cables. Plug the large 20-pin ribbon connector into the 20-pin connector on the lower control board. Attach the two grounding wire connectors to the two grounding wires located in the motor pan near the front of the frame. Connect the TV power cable to the TV power connector and coaxial cable to the coaxial cable connector; both located on the inside of the motor compartment at the front of the treadmill. BLUE BAG 5 STEP Please refer to back cover for this procedure, then return to Step 6. AUTO-CALIBRATION 4 STEP TV Power Cable Coaxial Cable TV BRACKET WIRING

O w n e r’s G u i d e T9800 Series TREADMILLS ongratulations on the purchase of your VISION FITNESS T9800 Treadmill. You’ve taken an important step in offering your customers what they need to achieve their fitness goals with a Treadmill that is designed specifically to meet your facility’s needs. It is important to have complete knowledge of this piece of equipment before use. Please read this Owner’s Guide before using your new Treadmill. General Specifications: Height: 58” / 147 cm Length: 84” / 213 cm Width: 31” / 79 cm Weight: 355 lbs / 161 kg Maximum User Weight: 400 lbs / 180 kgs Belt Area: 22” x 63” / 56 cm x 160 cm Speed: 0.5 – 12 mph / 0.8 – 20 kph Elevation: 0 – 15% VISION FITNESS 500 South CP Avenue P.O. Box 280 Lake Mills, WI 53551 Ph: 1.800.335.4348 Fax: 1.920.648.3373 www.visionfitness.com C