Zte mf910l Manuals

1.� Log�in�to�the�4G�Mobile�Hotspot�configuration�page.
2. Select Settings > Wi-Fi Settings > Basic Settings.
3.� Change�the�Network Name (SSID)�or�the Pass
Phrase�(�Password)�in�the�Main�SSID/Guest�SSID�
area.
4. Click Apply.
4G Mode
After�a�client�device�is�successfully�connected�to�your�
device,�you�can�access�the�Internet�in Automatic�or�
Manual�mode.�The�default�mode�is�Automatic.
Mode
Operation
Automatic
Your�device�is�automatically�connected�
to�the�Internet,�and�you�can�surf�on�the�
Internet�through�the�client.
MF910L
Quick Start Guide
ZTE CORPORATION
NO.�55,�Hi-tech�Road�South,�ShenZhen,�P.R.China�
Postcode:�518057
Appearance
The�following�figure�is�for�your�reference�only.
1.�� Power�Key�
2.�� WPS�Key
•�
Press�and�hold�for�3�seconds�to�activate�the�
WPS�function.
•�
Press�to�view�the�Wi-Fi�SSID�and�password�on�
the�LCD�screen.
3.�� (U)SIM�Card�Cover�and�Reset�Hole
4.�� LCD�Screen
5.�� Charging/micro-USB�Jack
Indicators
When�the�device�is�powered�on,�the�following�icons�may�
be�displayed�on�the�LCD�screen.�For�a�description�of�the�
icons,�refer�to�the�following�table.
Icon
Description
Network�signal�strength.
2G, 3G, 4G
Network�system�type.�The�4G,�3G�
or�2G�icon�is�displayed�on�the�LCD�
screen�depending�on�the�connected�
network.
The�user�is�in�roaming�status.
Connected�to�the�Internet.
One�or�more�new�messages�are�
received.
Wi-Fi�status�and�the�number�of�
connected�users.
Battery�level.
Connection Scenarios
The�device�can�access�the�Internet�in�two�ways�and�it�
allows�multiple�clients�to�surf�on�the�Internet�at�the�same�
time.�The�following�figures�are�for�your�reference�only.�
•�
4G Mode: A�(U)SIM�card�can�be�used�to�access�the�������
Internet.
•�
Internet Wi-Fi Mode: Your�device�can�be�connected�
to�a�WLAN�device�(such�as�a�hotspot�device�or�
wireless�router)�through�Wi-Fi�to�access�the�Internet.�
The�WLAN�device�must�be�already�connected�to�the�
Internet.
      NOTE: Your�device�and�the�WLAN�device�must�be�in�
different�subnets.�
1.� Open�the�(U)SIM�card�cover.
       NOTE:
Do�not�remove�the�cover�rudely,�because�it�is�connected�
with�the�device.
2.� Install�a�(U)SIM�card�to�the�(U)SIM�card�slot.�
     WARNING! Your�device�does�not�support�the�micro-
SIM�card�and�nano-SIM�card�or�any�other�non-standard�
SIM�cards.�To�avoid�damage�to�the�device,�do�not�use�
those�cards�or�any�card�holders.
3.� Close�the�(U)SIM�card�cover.
Using Wi-Fi
1.� Power�on�your�device.
2.� Make�sure�your�computer�or�other�client�devices�
have� enabled� Wi-Fi,� and� search� for� available�
wireless�networks.����������������������������������������������������������������
    NOTE: Refer�to�your�Wi-Fi-enabled�client�device�
manual�for�further�details�on�how�to�search�for�
wireless�networks.�If�you�use�a�computer,�you�
need�to�set�your�computer�to�obtain�an�IP�address�
automatically.
3.� Select�the�Wi-Fi�name�(SSID)�of�your�device,�and�
click Connect.
4. Enter�the�Wi-Fi�password�if�necessary,�and�click�OK.
NOTE:�Refer�to�the�chapter Getting to Know the
Wi-Fi SSID and Password�to�get�the�default�Wi-Fi�
SSID�and�password.
5.� Wait�until�the�client�device�is�connected�to�your�
device�successfully.
Using a USB Cable
1.� Connect�a�computer�to�your�device�with�a�USB�
cable.
2.� Power�on�your�device.�The�operating�system�detects�
and�identifies�new�hardware,�and�automatically�
installs�the�hardware.
    NOTE:�If�the�system�does�not�automatically�launch�
installation,�you�can�run�the�installation�program�in�
the  My Computer / Smartbro PocketWifi��path.
3.� Wait�until�the�computer�is�connected�to�your�device�
successfully.
You�can�use�the�following�methods�to�get�the�default�Wi-
Fi�SSID�and�password.
•�
View�the�label�on�the�device.
•�
Press�the�WPS Key.�The�Wi-Fi�SSID�is�displayed�on�
the�screen.
    NOTE: Your�device�don’t�have�Wi-Fi�connection�
password,�it�will�keep�turning�on.
1.� Make�sure�the�connection�between�your�device�and�
the�client�device�is�correct.
2.� L a u n c h� t h e� I n t e r n e t� b r o w s e r� a n d� e n t e r�
http://192.168.1.1�or�
     http://www.smartbrosettings.net�in�the�address�bar.
    NOTE: It�is�recommended�that�you�use�IE�(7.0�or�
later),�Firefox�(15.0�or�later),�Opera�(10.0�or�later),�
Safari�(4.0�or�later),�or�Google�Chrome�(10.0�or�
later).
3.� Enter�the�password�to�log�in�to�the�4G�Mobile�
Hotspot�configuration�page.
NOTE: The�default�password�is smartbro.
Changing the Wi-Fi SSID or Pass-
word
Accessing the Internet
Getting to Know the Wi-Fi SSID and
Password
Logging in to the 4G Mobile Hotspot
Configuration Page
Connecting to Your Device
Installing Your Device
Getting to Know Your Device
Getting to Know Your Device
Getting to Know Your Device
Connecting to Your Device
Installing Your Device
Getting to Know Your Device

1
MF910L
Quick Start Guide
ZTE CORPORATION
NO. 55, Hi-tech Road South, Shenzhen, P.R.China
Postcode: 518057

1
MF910L
Қысқаша нұсқаулық